KWKongyang Wang

Kongyang Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kongyang Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on Erosion Model Optimization and Damage Law of Coiled Tubing

    by Binqi Zhang, Jingen Deng, Hai Lin, Jie Xu, Guiping Wang, Wei Yan, Kongyang Wang, Fuli Li

    Coiled tubing (CT) is used as a velocity string to transport high-velocity gas in drainage gas recovery technology. Sand particles flowing at high speed can cause serious erosion of the pipe wall. Long-term erosion wear leads to the degradation of the string strength and can even cause local perforation. In order to study the erosion wear problem of CT, a gas–solid erosion experimental device was established for a full-size pipe with different radii of curvature. A 3D laser confocal technique was used to examine and characterize the microscopic erosion morphology of the inner wall of the CT. The CFD erosion model was selected based on the erosion test data of the inner wall of the CT, and the erosion results of the Finnie model show minimal error and good agreement compared with other models. The average value of the error of the maximum erosion rate at different radii of curvature is 8.3%. The effect of the radius of curvature, gas velocity and solid particle size on the maximum erosion rate of the inner wall of the CT was analyzed based on the Finnie model. The results reveal that erosion wear occurs on the inner wall of the CT’s outer bend. As the radius of curvature is reduced, the maximum erosion rate and area increase, and the position of the maximum erosion rate gradually shifts toward the inlet. The maximum erosion rate is positively correlated with the gas flow rate. However, as the particle size increases, the maximum erosion rate shows a trend of first increasing, then decreasing and finally stabilizing, with a critical particle size of 200 μm. This study can provide theoretical guidance and methods for improving the service life of CT. The erosion rate of the tubing in old wells can be reduced by controlling production and employing appropriate sand control methods, while the erosion rate of tubing in new wells can be reduced by adjusting the wellbore trajectory.


  • Open Access

    Study on Geometric Characteristics and Quantitative Description Method of Casing Deformation during Shale Reservoir Hydraulic Fracturing

    by Kongyang Wang, Jingen Deng, Wei Yan, Dickson Muchiri Nguu, Qiwu Yin, Shengsong Huang

    Casing deformation is a common but serious problem experienced during hydraulic fracturing operations in shale reservoirs. The Multi-Finger Imaging Tool is used to measure the casing deformation where the casing inner diameter is the only parameter used to characterize the deformation. Many deformed casing geometric details are often ignored, and these geometric characteristics are helpful for revealing the casing deformation mechanism. In this study, we established a quantitative method to describe the casing deformation using methods of judging the similarity of curves. By comparing the field casing deformation sections and the initial casing section, we categorized the casing deformation sections into concave and elliptical types. Furthermore, using the centroid calculation, elliptical type was sub-divided into symmetric ellipse type and eccentric ellipse type. On the basis of the Weiyuan and Guandong oil field’s fault distribution maps, we demonstrated that the fault slip could be the main cause of concave type and eccentric ellipse type. A numerical study was then carried out to ascertain whether fault slip can cause concave type and eccentric ellipse type casing deformations and to establish the relationship between fault slip magnitude and casing deformation. The results support the idea that concave type and eccentric ellipse type casing deformation are caused by the fault slip. Sensitivity analysis showed that the shape of the casing section was largely influenced by the dip angle, while the change of the casing inner diameter was largely influenced by the strike angle. The method proposed herein presents a useful step towards the prediction of the causes of casing deformation and provides a relationship between casing inner diameter change and fault slip.