Yanzhong Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yanzhong Wang has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Delong Dou
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
3 shared publications - Bin Xie
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
2 shared publications - Shiyuan E
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
2 shared publications - Chao Guo
School of Mechanical Engineering and Automation Beihang University 100191 Beijing China
1 shared publication - Daxun Yue
Key Laboratory of Advanced Manufacturing and Intelligent Technology, Ministry of Education, Harbin University of Science and Technology, Harbin, People’s Republic of China
1 shared publication Fengxia Lu
National Key Laboratory of Science and Technology on Helicopter Transmission, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication
Latest Publications
- Open Access
Dynamic Characteristics of a Transmission System Based on Tooth Surface Modification of Double-Pressure-Angle Helical Face Gears
To investigate the dynamic characteristics of a double-pressure-angle helical face gear transmission system, a digital tooth surface of a double-pressure-angle helical face gear, considering tooth surface modification, was established based on the generation principle of a disk grinding wheel. The time-varying mesh stiffness (TVMS) of the gear pair was calculated using the loaded tooth contact analysis (LTCA) method. A dynamic model of the double-pressure-angle helical face gear transmission system was then developed using the lumped-mass method, and the corresponding dynamic equations were derived. The dynamic characteristics of the system, as well as the effects of input speed, drive-side pressure angle, and tooth surface modification, were analyzed. The results show that increasing the drive-side pressure angle reduces the peak displacement vibration along the line of action, with a reduction of 31% at 32° compared with 24°. The input speed has a significant effect on the system dynamic response; as the speed increases, the vibration response first increases and then decreases, reaching its maximum at 9600 rpm. Bidirectional tooth surface modification on the drive side of the helical face gear changes the geometric contact pattern of the gear pair from localized concentration to a more uniform distribution. Meanwhile, the scatter points on the Poincaré section change from dispersed to concentrated, and the main acceleration peak along the line of action is reduced by 45.8%. These results provide theoretical support for the dynamic design of helical face gear transmission systems.
Open AccessDynamic Characteristics of a Transmission System Based on Tooth Surface Modification of Double-Pressure-Angle Helical Face Gears
To investigate the dynamic characteristics of a double-pressure-angle helical face gear transmission system, a digital tooth surface of a double-pressure-angle helical face gear, considering tooth surface modification, was established based on the generation principle of a disk grinding wheel. The time-varying mesh stiffness (TVMS) of the gear pair was calculated using the loaded tooth contact analysis (LTCA) method. A dynamic model of the double-pressure-angle helical face gear transmission system was then developed using the lumped-mass method, and the corresponding dynamic equations were derived. The dynamic characteristics of the system, as well as the effects of input speed, drive-side pressure angle, and tooth surface modification, were analyzed. The results show that increasing the drive-side pressure angle reduces the peak displacement vibration along the line of action, with a reduction of 31% at 32° compared with 24°. The input speed has a significant effect on the system dynamic response; as the speed increases, the vibration response first increases and then decreases, reaching its maximum at 9600 rpm. Bidirectional tooth surface modification on the drive side of the helical face gear changes the geometric contact pattern of the gear pair from localized concentration to a more uniform distribution. Meanwhile, the scatter points on the Poincaré section change from dispersed to concentrated, and the main acceleration peak along the line of action is reduced by 45.8%. These results provide theoretical support for the dynamic design of helical face gear transmission systems.
- Open Access
- 1 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12707
Tooth Surface Contact Characteristics of Non-Circular Gear Based on Ease-off Modification
To address edge contact in non-circular gears arising from installation errors, a modification strategy represented by elliptical gears and driven by an ease-off topological surface is proposed. A tooth surface model for non-circular gears was first derived from meshing theory. The modification magnitude was defined using a second-order ease-off differential surface, and the modified surface is represented through non-uniform rational B-spline (NURBS) fitting. A tooth contact analysis (TCA) model is then built to evaluate how installation errors and modification amount influence contact behavior. The results indicate that an increase in center distance error reduces the contact ratio. For equal perturbations of axial horizontal and axial vertical mounting angles, the horizontal error has the stronger impact on the size and location of the contact patch. As the longitudinal modification coefficient grows, the contact path and peak pressure position shift from the tooth edge toward the mid-width; the contact ellipse first enlarges and then shrinks, while the contact pressure shows the opposite trend. The elastic deformation of the tooth surface increases with the mounting angle. Transmission tests confirm that the proposed modification lowers the transmission error relative to the unmodified gear pair.
- 1 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12707
Open AccessTooth Surface Contact Characteristics of Non-Circular Gear Based on Ease-off Modification
To address edge contact in non-circular gears arising from installation errors, a modification strategy represented by elliptical gears and driven by an ease-off topological surface is proposed. A tooth surface model for non-circular gears was first derived from meshing theory. The modification magnitude was defined using a second-order ease-off differential surface, and the modified surface is represented through non-uniform rational B-spline (NURBS) fitting. A tooth contact analysis (TCA) model is then built to evaluate how installation errors and modification amount influence contact behavior. The results indicate that an increase in center distance error reduces the contact ratio. For equal perturbations of axial horizontal and axial vertical mounting angles, the horizontal error has the stronger impact on the size and location of the contact patch. As the longitudinal modification coefficient grows, the contact path and peak pressure position shift from the tooth edge toward the mid-width; the contact ellipse first enlarges and then shrinks, while the contact pressure shows the opposite trend. The elastic deformation of the tooth surface increases with the mounting angle. Transmission tests confirm that the proposed modification lowers the transmission error relative to the unmodified gear pair.
- Open Access
- 16 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (16) , 9046
A Fourth-Order Moment Method Based on Back Propagation Neural Network for High-Dimensional Nonlinear Reliability Analysis
Reliability analysis of complex engineering products often involves high-dimensional nonlinear state functions, with random variable distributions hard to determine due to limited samples, restricting the fourth-order moment method that fails to link moments of variables and state functions. This study proposes a method combining a back propagation (BP) neural network and a fourth-order moment method: a BP neural network surrogates the mapping between the model approximation variables and the state function, generating samples for estimating the first-fourth-order moments of the state function, and thus performing reliability analyses based on the fourth-order moment method. Validation shows the BP model outperforms Kriging in predicting high-dimensional nonlinear functions; it aligns with Monte Carlo simulation (MCS) results in rolling bearing reliability analysis with higher efficiency and applies to time-varying fatigue analysis. This method overcomes limitations of the fourth-order moment method, offers higher accuracy than existing surrogate-based methods, and retains the efficiency of moment methods, suitable for limited-sample and time-varying scenarios.
- 16 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (16) , 9046
Open AccessA Fourth-Order Moment Method Based on Back Propagation Neural Network for High-Dimensional Nonlinear Reliability Analysis
Reliability analysis of complex engineering products often involves high-dimensional nonlinear state functions, with random variable distributions hard to determine due to limited samples, restricting the fourth-order moment method that fails to link moments of variables and state functions. This study proposes a method combining a back propagation (BP) neural network and a fourth-order moment method: a BP neural network surrogates the mapping between the model approximation variables and the state function, generating samples for estimating the first-fourth-order moments of the state function, and thus performing reliability analyses based on the fourth-order moment method. Validation shows the BP model outperforms Kriging in predicting high-dimensional nonlinear functions; it aligns with Monte Carlo simulation (MCS) results in rolling bearing reliability analysis with higher efficiency and applies to time-varying fatigue analysis. This method overcomes limitations of the fourth-order moment method, offers higher accuracy than existing surrogate-based methods, and retains the efficiency of moment methods, suitable for limited-sample and time-varying scenarios.
- Open Access
The Dynamic Comprehensive Evaluation of the Importance of Cutting Parameters in the Side Milling TC4 Process Using an Integrated End Mill
In the cutting process, there are many parameters that affect the cutting effect, and the same parameter has different degrees of influence on different performance indicators, which makes it difficult to select key parameters for parameter optimization and parameter combination evaluation while considering multiple performance indicators at the same time. The process of titanium alloy milling with an integrated end mill is studied herein. The values of cutting tool flank face wear and material removal rates are obtained with experimental and analytical methods. Numerical characteristics and causes of the cutting tool flank face wear at different stages are also analyzed. The dynamic, comprehensive evaluation method based on the double incentives model is used to evaluate the dynamic, comprehensive importance of cutting parameters in view of the problem of considering multiple performance indicators and the characteristics of the dynamic change in performance indicators in the cutting process. According to the result of a dynamic, comprehensive evaluation, the cutting parameters with the highest comprehensive importance are selected. Finally, the radar map is used to plot the comprehensive importance of the cutting parameters. The overall comprehensive importance of each cutting parameter is intuitively displayed as well. As a result of the research, the dynamic, comprehensive evaluation method based on the double incentives model has a good application value in the evaluation of tool performance in the cutting process and can quickly select the best tool performance parameter combination; it is established that the most comprehensive parameter is the cutting speed, and the cutting width is the second most important. In turn, the comprehensive importance of the cutting depth is the lowest.
Open AccessThe Dynamic Comprehensive Evaluation of the Importance of Cutting Parameters in the Side Milling TC4 Process Using an Integrated End Mill
In the cutting process, there are many parameters that affect the cutting effect, and the same parameter has different degrees of influence on different performance indicators, which makes it difficult to select key parameters for parameter optimization and parameter combination evaluation while considering multiple performance indicators at the same time. The process of titanium alloy milling with an integrated end mill is studied herein. The values of cutting tool flank face wear and material removal rates are obtained with experimental and analytical methods. Numerical characteristics and causes of the cutting tool flank face wear at different stages are also analyzed. The dynamic, comprehensive evaluation method based on the double incentives model is used to evaluate the dynamic, comprehensive importance of cutting parameters in view of the problem of considering multiple performance indicators and the characteristics of the dynamic change in performance indicators in the cutting process. According to the result of a dynamic, comprehensive evaluation, the cutting parameters with the highest comprehensive importance are selected. Finally, the radar map is used to plot the comprehensive importance of the cutting parameters. The overall comprehensive importance of each cutting parameter is intuitively displayed as well. As a result of the research, the dynamic, comprehensive evaluation method based on the double incentives model has a good application value in the evaluation of tool performance in the cutting process and can quickly select the best tool performance parameter combination; it is established that the most comprehensive parameter is the cutting speed, and the cutting width is the second most important. In turn, the comprehensive importance of the cutting depth is the lowest.
- Open Access
- 25 June 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (13) , 2843
A Reliability-Based Robust Design Optimization Method for Rolling Bearing Fatigue under Cyclic Load Spectrum
Reliability-based robust design methods have been widely used in the field of product design; however, they are difficult to apply to the fatigue reliability design process of rolling bearings due to the problems of determining fatigue accumulated damage caused by the internal cyclic time-varying load distribution of rolling bearings and the computational cost of time-varying reliability. Therefore, a reliability-based robust design method for rolling bearing fatigue failure is proposed, which derives the formula for fatigue accumulated damage of a rolling bearing under cyclic load spectrum and significantly reduces the computational cost of rolling bearing time-varying reliability compared with existing methods. First, the state response of a rolling bearing under random design parameters is obtained by finite element simulation. Then, the adaptive kriging method is used to characterize the correlation between the random parameters and the state response. The Miner fatigue cumulative damage theory is improved and the rolling bearing fatigue time-varying equation of state under cyclic load spectrum is derived. Subsequently, a fatigue time-varying reliability model based on an improved fourth-order moment method is developed, and a reliability robust optimization design method is proposed. Finally, a rolling bearing example is presented to demonstrate that the method achieves time-varying fatigue reliability design under cyclic load spectrum and effectively improves the reliability and robustness of the product design.
- 25 June 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (13) , 2843
Open AccessA Reliability-Based Robust Design Optimization Method for Rolling Bearing Fatigue under Cyclic Load Spectrum
Reliability-based robust design methods have been widely used in the field of product design; however, they are difficult to apply to the fatigue reliability design process of rolling bearings due to the problems of determining fatigue accumulated damage caused by the internal cyclic time-varying load distribution of rolling bearings and the computational cost of time-varying reliability. Therefore, a reliability-based robust design method for rolling bearing fatigue failure is proposed, which derives the formula for fatigue accumulated damage of a rolling bearing under cyclic load spectrum and significantly reduces the computational cost of rolling bearing time-varying reliability compared with existing methods. First, the state response of a rolling bearing under random design parameters is obtained by finite element simulation. Then, the adaptive kriging method is used to characterize the correlation between the random parameters and the state response. The Miner fatigue cumulative damage theory is improved and the rolling bearing fatigue time-varying equation of state under cyclic load spectrum is derived. Subsequently, a fatigue time-varying reliability model based on an improved fourth-order moment method is developed, and a reliability robust optimization design method is proposed. Finally, a rolling bearing example is presented to demonstrate that the method achieves time-varying fatigue reliability design under cyclic load spectrum and effectively improves the reliability and robustness of the product design.
- Open Access
Dynamic Features of Non-Return Mechanism in Hatch Door of Amphibious Aircraft
The non-return mechanism is the key device that plays the role of braking in the opening-and-closing electric actuator of an amphibious aircraft hatch door. The ball-and-socket contact pair, providing the pressing force, and the multi-disc friction pair, supplying the braking torque, are two core components in the non-return mechanism. In this paper, the dynamic model of the non-return mechanism is established considering the freedom of rotation-translation. Based on MATLAB/Simulink, the solution framework of the overall dynamic model is built. The dynamic response characteristics of the non-return mechanism in the process of reverse load braking, forward load braking, and continuous closing are analyzed. The braking time and the angular displacement of the output shaft in the braking phase have been presented. Compared with forward load braking, reverse load braking has a longer braking time and smaller angular displacement of the output shaft. In addition, the compaction function of the ball-and-socket contact pair is verified by experiment, and the influence of the cone angle, distribution radius of the ball socket, and the steel ball diameter on the pressing force has been discussed. This study provides a theoretical basis and parametric design platform for the design and optimization of non-return mechanisms, which can shorten the product development time.
Open AccessDynamic Features of Non-Return Mechanism in Hatch Door of Amphibious Aircraft
The non-return mechanism is the key device that plays the role of braking in the opening-and-closing electric actuator of an amphibious aircraft hatch door. The ball-and-socket contact pair, providing the pressing force, and the multi-disc friction pair, supplying the braking torque, are two core components in the non-return mechanism. In this paper, the dynamic model of the non-return mechanism is established considering the freedom of rotation-translation. Based on MATLAB/Simulink, the solution framework of the overall dynamic model is built. The dynamic response characteristics of the non-return mechanism in the process of reverse load braking, forward load braking, and continuous closing are analyzed. The braking time and the angular displacement of the output shaft in the braking phase have been presented. Compared with forward load braking, reverse load braking has a longer braking time and smaller angular displacement of the output shaft. In addition, the compaction function of the ball-and-socket contact pair is verified by experiment, and the influence of the cone angle, distribution radius of the ball socket, and the steel ball diameter on the pressing force has been discussed. This study provides a theoretical basis and parametric design platform for the design and optimization of non-return mechanisms, which can shorten the product development time.
- 18 February 2023
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 66 (3) , 1-15
A novel reliability analysis method combining adaptive relevance vector machine and subset simulation for small failure probability
- 18 February 2023
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 66 (3) , 1-15
A novel reliability analysis method combining adaptive relevance vector machine and subset simulation for small failure probability
- 6 December 2022
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 15 (3) , 1-15
Thermal Behavior of Conical Friction Element Under Different Contact Pressure Boundaries
The high temperature generated on the contact interfaces of the conical friction element in clutches due to the sliding frictional heat should be responsible for the synchronization failure. In this study, an analytic model taking account of the capsizing moment and stress singularity at the end of the contact interface is established to solve the contact pressure distribution. Then, a three-dimensional finite element model has been developed to analyze the transient thermal behavior of the conical friction element. The contact pressure and temperature distribution generated along the contact interfaces are investigated and compared between the proposed new model, the combined wear assumption, and the uniform pressure assumption. Furthermore, the variations in temperature obtained from the new model and the other two assumptions are compared to the experimental results. The results show that the temperature simulated by the new model has a good agreement with reality. The maximum temperatures obtained by the new model are 95.53 °C and 71.67 °C, and the measured values are respectively 84.98 °C and 65.46 °C at the measuring position under the given two working conditions.
- 6 December 2022
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 15 (3) , 1-15
Thermal Behavior of Conical Friction Element Under Different Contact Pressure Boundaries
The high temperature generated on the contact interfaces of the conical friction element in clutches due to the sliding frictional heat should be responsible for the synchronization failure. In this study, an analytic model taking account of the capsizing moment and stress singularity at the end of the contact interface is established to solve the contact pressure distribution. Then, a three-dimensional finite element model has been developed to analyze the transient thermal behavior of the conical friction element. The contact pressure and temperature distribution generated along the contact interfaces are investigated and compared between the proposed new model, the combined wear assumption, and the uniform pressure assumption. Furthermore, the variations in temperature obtained from the new model and the other two assumptions are compared to the experimental results. The results show that the temperature simulated by the new model has a good agreement with reality. The maximum temperatures obtained by the new model are 95.53 °C and 71.67 °C, and the measured values are respectively 84.98 °C and 65.46 °C at the measuring position under the given two working conditions.
- Open Access
- 25 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3345
Investigation of Load Capacity of High-Contact-Ratio Internal Spur Gear Drive with Arc Path of Contact
Tooth root bending stress and surface contact stress are two major determinants of the load carrying capacity of gear drives. Generally, a high contact ratio has the potential to enhance the gear strength. In this paper, the basic procedures and methods for constructing a high-contact-ratio (HCR) internal spur gear pair with the arc path of the contact are presented. The effects of design and modification parameters such as deflection angle, modification angle, and addendum coefficient on gear drive are analyzed in detail based on 2D finite-element models (FEMs). A comparison of experimental and finite-element analyses (FEA) of the bending stress, contact stress, and contact ratio between HCR and involute internal spur gear drives was conducted to demonstrate the advantages of the HCR gear drive in terms of load capacity. The results show that appropriately increasing the deflection angle and addendum coefficient is beneficial for reducing bending and contact stresses. It was also observed that the bending and contact stresses of a HCR pinion are lower than those of an involute one. Moreover, the contact ratio increases with input torque.
- 25 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3345
Open AccessInvestigation of Load Capacity of High-Contact-Ratio Internal Spur Gear Drive with Arc Path of Contact
Tooth root bending stress and surface contact stress are two major determinants of the load carrying capacity of gear drives. Generally, a high contact ratio has the potential to enhance the gear strength. In this paper, the basic procedures and methods for constructing a high-contact-ratio (HCR) internal spur gear pair with the arc path of the contact are presented. The effects of design and modification parameters such as deflection angle, modification angle, and addendum coefficient on gear drive are analyzed in detail based on 2D finite-element models (FEMs). A comparison of experimental and finite-element analyses (FEA) of the bending stress, contact stress, and contact ratio between HCR and involute internal spur gear drives was conducted to demonstrate the advantages of the HCR gear drive in terms of load capacity. The results show that appropriately increasing the deflection angle and addendum coefficient is beneficial for reducing bending and contact stresses. It was also observed that the bending and contact stresses of a HCR pinion are lower than those of an involute one. Moreover, the contact ratio increases with input torque.
- 6 November 2017
- Published by Emerald Publishing in Engineering Computations
- Vol. 34 (8) , 2877-2898
Parametric finite element modeling and tooth contact analysis of spur and helical gears including profile and lead modifications
Purpose The finite element method has been increasingly applied in stress, thermal and dynamic analysis of gear transmissions. Preparing the models with different design and modification parameters for the finite element analysis is a time-consuming and highly skilled burden. Design/methodology/approach To simplify the preprocessing work of the analysis, a parametric finite element modeling method for spur and helical gears including profile and lead modification is developed. The information about the nodes and elements is obtained and exported into the finite element software to generate the finite element model of the gear automatically. Findings By using the three-dimensional finite element tooth contact analysis method, the effects of tooth modifications on the transmission error and contact stress of spur and helical gears are presented. Originality/value The results demonstrate that the proposed method is useful for verifying the modification parameters of spur and helical gears in the case of deformations and misalignments.
- 6 November 2017
- Published by Emerald Publishing in Engineering Computations
- Vol. 34 (8) , 2877-2898
Parametric finite element modeling and tooth contact analysis of spur and helical gears including profile and lead modifications
Purpose The finite element method has been increasingly applied in stress, thermal and dynamic analysis of gear transmissions. Preparing the models with different design and modification parameters for the finite element analysis is a time-consuming and highly skilled burden. Design/methodology/approach To simplify the preprocessing work of the analysis, a parametric finite element modeling method for spur and helical gears including profile and lead modification is developed. The information about the nodes and elements is obtained and exported into the finite element software to generate the finite element model of the gear automatically. Findings By using the three-dimensional finite element tooth contact analysis method, the effects of tooth modifications on the transmission error and contact stress of spur and helical gears are presented. Originality/value The results demonstrate that the proposed method is useful for verifying the modification parameters of spur and helical gears in the case of deformations and misalignments.