José Félix Guil-Pedrosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
José Félix Guil-Pedrosa has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Soria-Verdugo
Thermal and Fluids Engineering Department, University Carlos III of Madrid, Avda. de la Universidad 30, 28911 Leganés, Madrid, Spain
8 shared publications - Luis Miguel Garcia-Gutierrez
Department of Thermal and Fluids Engineering, University Carlos III of Madrid, Av. Universidad 30, Leganés, Madrid, Spain
6 shared publications - Eduardo Cano-Pleite
Department of Thermal and Fluids Engineering, University Carlos III of Madrid, Av. Universidad 30, Leganés, Madrid, Spain
4 shared publications - Nestor Garcia-Hernando
ISE Research Group, Department Thermal and Fluids Engineering, UC3M, 28911 Madrid, Spain
3 shared publications - Andrés Anca-Couce
Thermal and Fluids Engineering Department, Carlos III University of Madrid, Avda. de la Universidad 30, 28911 Leganés, Madrid, Spain
2 shared publications - Sylvie Lorente
Mechanical Engineering Department, Villanova University, Villanova, USA
2 shared publications
Latest Publications
- Open Access
- 28 October 2026
- Published by Elsevier in Combustion and Flame
- Vol. 295
Accurate modelling of biomass char particle oxidation with a novel external heat and mass transfer correlation and an appropriate CO/CO2 ratio
- 28 October 2026
- Published by Elsevier in Combustion and Flame
- Vol. 295
Open AccessAccurate modelling of biomass char particle oxidation with a novel external heat and mass transfer correlation and an appropriate CO/CO2 ratio
- Open Access
- 19 February 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 261
Analysis of single-channel and canopy-to-canopy cold plate cooling systems under cyclic operation
- 19 February 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 261
Open AccessAnalysis of single-channel and canopy-to-canopy cold plate cooling systems under cyclic operation
- Open Access
- 11 August 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 279
Numerical and experimental study of the optimum size of flat plate cooling systems with different channel shapes
- 11 August 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 279
Open AccessNumerical and experimental study of the optimum size of flat plate cooling systems with different channel shapes
- Open Access
- 7 April 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 214
Experimental and numerical analysis of a novel constructal design for canopy-to-canopy liquid cooling systems
- 7 April 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 214
Open AccessExperimental and numerical analysis of a novel constructal design for canopy-to-canopy liquid cooling systems
- 1 November 2024
- Published by IATED Academy
- Vol. 1, 6877-6881
EXPLORING THE INTEGRATION OF AN AI-ASSISTED MIDTERM EXAM IN A THERMAL ENGINES COURSE
- 1 November 2024
- Published by IATED Academy
- Vol. 1, 6877-6881
EXPLORING THE INTEGRATION OF AN AI-ASSISTED MIDTERM EXAM IN A THERMAL ENGINES COURSE
- 6 October 2023
- Published by Elsevier in Journal of Energy Storage
- Vol. 73, 109173
Experimental study of the discharge process of a thermal energy storage system based on granular material operated as a fluidized or confined bed
- 6 October 2023
- Published by Elsevier in Journal of Energy Storage
- Vol. 73, 109173
Experimental study of the discharge process of a thermal energy storage system based on granular material operated as a fluidized or confined bed
- Open Access
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
The influence of an outer bath on the dewetting of an ultrathin liquid film
We report a theoretical and numerical investigation of the linear and nonlinear dynamics of a thin liquid film of viscosity μ sandwiched between a solid substrate and an unbounded liquid bath of viscosity λμ. In the limit of negligible inertia, the flow depends on two non-dimensional parameters, namely, λ and a dimensionless measure of the relative strengths of the stabilizing surface tension force and the destabilizing van der Waals force between the substrate and the film. We first analyze the linear stability of the film, providing an analytical dispersion relation. When the viscosity of the outer bath is much larger than that of the film, λ≫1, the most amplified wavenumber decreases as km∼λ−1/3, indicating that very slender dewetting structures are expected when λ becomes large. We then perform fully nonlinear simulations of the complete Stokes equations to investigate the spatial structure of the flow close to rupture revealing that the flow becomes self-similar with the minimum film thickness scaling as hmin=K(λ)τ1/3 when τ→0, where τ is the time remaining before the singularity. It is demonstrated that the presence of an outer liquid bath affects the self-similar structure obtained by Moreno-Boza et al. [“Stokes theory of thin-film rupture,” Phys. Rev. Fluids 5, 014002 (2020)] through the prefactor of the film thinning law, K(λ), and the opening angle of the self-similar film shape, which is shown to decrease with λ.
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
Open AccessThe influence of an outer bath on the dewetting of an ultrathin liquid film
We report a theoretical and numerical investigation of the linear and nonlinear dynamics of a thin liquid film of viscosity μ sandwiched between a solid substrate and an unbounded liquid bath of viscosity λμ. In the limit of negligible inertia, the flow depends on two non-dimensional parameters, namely, λ and a dimensionless measure of the relative strengths of the stabilizing surface tension force and the destabilizing van der Waals force between the substrate and the film. We first analyze the linear stability of the film, providing an analytical dispersion relation. When the viscosity of the outer bath is much larger than that of the film, λ≫1, the most amplified wavenumber decreases as km∼λ−1/3, indicating that very slender dewetting structures are expected when λ becomes large. We then perform fully nonlinear simulations of the complete Stokes equations to investigate the spatial structure of the flow close to rupture revealing that the flow becomes self-similar with the minimum film thickness scaling as hmin=K(λ)τ1/3 when τ→0, where τ is the time remaining before the singularity. It is demonstrated that the presence of an outer liquid bath affects the self-similar structure obtained by Moreno-Boza et al. [“Stokes theory of thin-film rupture,” Phys. Rev. Fluids 5, 014002 (2020)] through the prefactor of the film thinning law, K(λ), and the opening angle of the self-similar film shape, which is shown to decrease with λ.
- Open Access
- 25 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3350
Design of Novel Cooling Systems Based on Metal Plates with Channels of Shapes Inspired by Nature
The effect of the channel shape of aluminum plates on cooling capacity was evaluated by studying different configurations. Common shapes of the channel, such as square and fork shapes, were compared with novel configurations inspired by shapes found in nature, specifically the shape of the outline of flowers, inspired these new configurations, consisting of channels with crateriform, salverform, and cruciform shapes. The aim of the study is to evaluate the effect of the channel shape on the cooling capacity of the metal plate. To that end, all the configurations were analyzed from a geometrical point of view, determining the minimum distance of each point across the plate to the channel. A finite difference method was implemented to study both transient and steady state heat dissipation across the plates for each configuration. Even though the effect of the channel shape on the average temperature of the plate is slight, the maximum temperature, the size and location of hot spots, and the temperature homogeneity of the plate are strongly affected by the shape of the channel through which the cooling fluid is circulated. A reduction in the maximum temperature of the plate during transient cooling of around 2 °C for the crateriform and salverform channels and approximately 4.5 °C for the cruciform channel can be attained, compared to the standard configurations. The steady state heat dissipation analysis concluded that the crateriform and salverform configurations reduced the maximum variation in temperature of the common configurations by roughly 15%, whereas a reduction of approximately 28% could be reached by the cruciform configuration. Regarding the homogeneity of temperature across the plate, a reduction up to 34.5% of the index of uniform temperature can be attained using the novel configurations during the steady state refrigeration of the plate. The cruciform channel is the optimal configuration for both transient and steady state cooling processes, reducing the size and temperature of hot spots and improving the temperature homogeneity of the plate, a result already anticipated by the geometrical analysis. In fact, the main conclusions attained from the cooling study are in good agreement with the results of the geometrical analysis. Therefore, the geometrical analysis was found to be a simple and reliable method to design the shape of channels of a cooling system.
- 25 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3350
Open AccessDesign of Novel Cooling Systems Based on Metal Plates with Channels of Shapes Inspired by Nature
The effect of the channel shape of aluminum plates on cooling capacity was evaluated by studying different configurations. Common shapes of the channel, such as square and fork shapes, were compared with novel configurations inspired by shapes found in nature, specifically the shape of the outline of flowers, inspired these new configurations, consisting of channels with crateriform, salverform, and cruciform shapes. The aim of the study is to evaluate the effect of the channel shape on the cooling capacity of the metal plate. To that end, all the configurations were analyzed from a geometrical point of view, determining the minimum distance of each point across the plate to the channel. A finite difference method was implemented to study both transient and steady state heat dissipation across the plates for each configuration. Even though the effect of the channel shape on the average temperature of the plate is slight, the maximum temperature, the size and location of hot spots, and the temperature homogeneity of the plate are strongly affected by the shape of the channel through which the cooling fluid is circulated. A reduction in the maximum temperature of the plate during transient cooling of around 2 °C for the crateriform and salverform channels and approximately 4.5 °C for the cruciform channel can be attained, compared to the standard configurations. The steady state heat dissipation analysis concluded that the crateriform and salverform configurations reduced the maximum variation in temperature of the common configurations by roughly 15%, whereas a reduction of approximately 28% could be reached by the cruciform configuration. Regarding the homogeneity of temperature across the plate, a reduction up to 34.5% of the index of uniform temperature can be attained using the novel configurations during the steady state refrigeration of the plate. The cruciform channel is the optimal configuration for both transient and steady state cooling processes, reducing the size and temperature of hot spots and improving the temperature homogeneity of the plate, a result already anticipated by the geometrical analysis. In fact, the main conclusions attained from the cooling study are in good agreement with the results of the geometrical analysis. Therefore, the geometrical analysis was found to be a simple and reliable method to design the shape of channels of a cooling system.