Lei Ji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lei Ji has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Demin Liu
Dongfang Electric Machinery Co., Ltd., Dongfang Electric Corporation, Deyang 618000, China
2 shared publications - Wanquan Deng
Key Laboratory of Fluid Machinery and Engineering, Xihua University, Chengdu 610039, China
2 shared publications - Wei Han
School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Xiaobing Liu
Key Laboratory of Fluid and Power Machinery, Ministry of Education, Xihua University, Chengdu 610039, China
2 shared publications - Zhen Li
Key Laboratory of Fluid and Power Machinery, Ministry of Education, Xihua University, Chengdu 610039, China
2 shared publications - Hongfa Huang
Natural Gas Research Institute, Petro China Southwest Oil & Gas Field Company, Chengdu 610213, China
1 shared publication
Latest Publications
- Open Access
Optimization of Inlet Flow Pattern and Performance Enhancement in Oil-Gas Multiphase Pumps Using Helical Static Mixer
With increasing global energy demand and depletion of onshore oil–gas resources, deep-sea hydrocarbon exploration and development have become strategically vital. As core subsea transportation equipment, the performance of helico-axial multiphase pumps directly determines the efficiency and economic feasibility of deep-sea extraction. However, non-uniform inflow patterns caused by uneven gas–liquid distribution in pipelines degrade pressure-boosting capability and reduce pump efficiency under actual operating conditions. To address this, an optimization method employing helical static mixers was developed. A mixer with a 180° helical angle was designed and installed upstream of the pump inlet. Numerical simulations demonstrate that the mixer enhances gas-phase distribution uniformity in stratified flow, improving efficiency and head across varying gas void fractions (GVFs). At a stratification height ratio (Ψ) of 0.32, efficiency increased by 15.41% and head rose by 15.64 m, while turbulent kinetic energy (TKE) at the impeller outlet decreased by up to 50%. For slug flow conditions, the mixer effectively suppressed gas volume fraction fluctuations, consistently improving efficiency under different slug flow coefficients (φ) with a maximum head increase of 9.82%. The optimized flow field exhibits uniform gas–liquid velocity distribution, stable pressure boosting, and significantly reduced TKE intensity within impeller passages.
Open AccessOptimization of Inlet Flow Pattern and Performance Enhancement in Oil-Gas Multiphase Pumps Using Helical Static Mixer
With increasing global energy demand and depletion of onshore oil–gas resources, deep-sea hydrocarbon exploration and development have become strategically vital. As core subsea transportation equipment, the performance of helico-axial multiphase pumps directly determines the efficiency and economic feasibility of deep-sea extraction. However, non-uniform inflow patterns caused by uneven gas–liquid distribution in pipelines degrade pressure-boosting capability and reduce pump efficiency under actual operating conditions. To address this, an optimization method employing helical static mixers was developed. A mixer with a 180° helical angle was designed and installed upstream of the pump inlet. Numerical simulations demonstrate that the mixer enhances gas-phase distribution uniformity in stratified flow, improving efficiency and head across varying gas void fractions (GVFs). At a stratification height ratio (Ψ) of 0.32, efficiency increased by 15.41% and head rose by 15.64 m, while turbulent kinetic energy (TKE) at the impeller outlet decreased by up to 50%. For slug flow conditions, the mixer effectively suppressed gas volume fraction fluctuations, consistently improving efficiency under different slug flow coefficients (φ) with a maximum head increase of 9.82%. The optimized flow field exhibits uniform gas–liquid velocity distribution, stable pressure boosting, and significantly reduced TKE intensity within impeller passages.
- Open Access
Solid–Liquid Two-Phase Flowmeter Flow-Passage Wall Erosion Evolution Characteristics and Calibration of Measurement Accuracy
Solid–liquid two-phase flowmeters are widely used in critical sectors, such as petrochemicals, energy, manufacturing, the environment, and various other fields. They are indispensable devices for measuring flow. Currently, research has primarily focused on gas–liquid two-phase flow within the flowmeter, giving limited attention to the impact of solid phases. In practical applications, crude oil frequently contains solid particles and other impurities, leading to equipment deformation and a subsequent reduction in measuring accuracy. This paper investigates how particle dynamic parameters affect the erosion evolution characteristics of flowmeters operating in solid–liquid two-phase conditions, employing the dynamic boundary erosion prediction method. The results indicate that the erosion range and peak erosion position on the overcurrent wall of the solid–liquid two-phase flowmeter vary with different particle dynamic parameters. Erosion mainly occurs at the contraction section of the solid–liquid two-phase flowmeter. When the particle inflow velocity increases, the erosion range shows no significant change, but the peak erosion position shifts to the right, primarily due to the evolution of the erosion process. With an increase in particle diameter, the erosion range expands along the inlet direction due to turbulent diffusion, as particles with lower kinetic energy exhibit better followability. There is no significant change in the erosion range and peak erosion position with an increase in particle volume fraction and particle sphericity. With a particle inflow velocity of 8.4 m/s, the maximum erosion depth reaches 750 μm. In contrast, at a particle sphericity of 0.58, the minimum erosion depth is 251 μm. Furthermore, a particle volume fraction of 0.5 results in a maximum flow coefficient increase of 1.99 × 10−3.
Open AccessSolid–Liquid Two-Phase Flowmeter Flow-Passage Wall Erosion Evolution Characteristics and Calibration of Measurement Accuracy
Solid–liquid two-phase flowmeters are widely used in critical sectors, such as petrochemicals, energy, manufacturing, the environment, and various other fields. They are indispensable devices for measuring flow. Currently, research has primarily focused on gas–liquid two-phase flow within the flowmeter, giving limited attention to the impact of solid phases. In practical applications, crude oil frequently contains solid particles and other impurities, leading to equipment deformation and a subsequent reduction in measuring accuracy. This paper investigates how particle dynamic parameters affect the erosion evolution characteristics of flowmeters operating in solid–liquid two-phase conditions, employing the dynamic boundary erosion prediction method. The results indicate that the erosion range and peak erosion position on the overcurrent wall of the solid–liquid two-phase flowmeter vary with different particle dynamic parameters. Erosion mainly occurs at the contraction section of the solid–liquid two-phase flowmeter. When the particle inflow velocity increases, the erosion range shows no significant change, but the peak erosion position shifts to the right, primarily due to the evolution of the erosion process. With an increase in particle diameter, the erosion range expands along the inlet direction due to turbulent diffusion, as particles with lower kinetic energy exhibit better followability. There is no significant change in the erosion range and peak erosion position with an increase in particle volume fraction and particle sphericity. With a particle inflow velocity of 8.4 m/s, the maximum erosion depth reaches 750 μm. In contrast, at a particle sphericity of 0.58, the minimum erosion depth is 251 μm. Furthermore, a particle volume fraction of 0.5 results in a maximum flow coefficient increase of 1.99 × 10−3.
- Open Access
Experimental Study on a New Combined Gas–Liquid Separator
Gas–liquid separation at natural gas wellheads has always been a key technical problem in the fields of natural gas transportation and storage. Developing a gas–liquid separation device that is both universal and highly efficient is the current challenge. A new type of combined gas–liquid separation device was designed in this study, and the efficiency of the separator was studied using a laser Doppler anemometer and phase Doppler particle analyzer at a flow rate of 10–60 Nm3/h. The results showed that the separation efficiency of the combined separator was above 95% at each experimental flow rate, verifying the strong applicability of the combined separator. Moreover, the separation efficiency was as high as 99% at the flow rates of 10 and 60 Nm3/h, thereby realizing efficient separation. This study is significant to the development of gas–liquid separation devices.
Open AccessExperimental Study on a New Combined Gas–Liquid Separator
Gas–liquid separation at natural gas wellheads has always been a key technical problem in the fields of natural gas transportation and storage. Developing a gas–liquid separation device that is both universal and highly efficient is the current challenge. A new type of combined gas–liquid separation device was designed in this study, and the efficiency of the separator was studied using a laser Doppler anemometer and phase Doppler particle analyzer at a flow rate of 10–60 Nm3/h. The results showed that the separation efficiency of the combined separator was above 95% at each experimental flow rate, verifying the strong applicability of the combined separator. Moreover, the separation efficiency was as high as 99% at the flow rates of 10 and 60 Nm3/h, thereby realizing efficient separation. This study is significant to the development of gas–liquid separation devices.
- Open Access
Laser Doppler Velocimetry Test of Flow Characteristics in Draft Tube of Model Pump Turbine
For Francis pump turbines, the pressure pulsation characteristics of the draft tube are some of the key concerns during the operation of the units. The pressure pulsation characteristics of the draft tube are directly related to the draft tube spiral cavitating vortex rope. In this paper, the velocity distribution in the draft tube of a Francis pump turbine is tested by means of laser Doppler velocimetry. The velocity pulsation was found to be directly related to the pressure pulsation, while the velocity pulsation was also influenced by the cavitation coefficient. The main frequency of the velocity pulsation was close to the main frequency of the pressure pulsation and became larger as the cavitation factor increased.
Open AccessLaser Doppler Velocimetry Test of Flow Characteristics in Draft Tube of Model Pump Turbine
For Francis pump turbines, the pressure pulsation characteristics of the draft tube are some of the key concerns during the operation of the units. The pressure pulsation characteristics of the draft tube are directly related to the draft tube spiral cavitating vortex rope. In this paper, the velocity distribution in the draft tube of a Francis pump turbine is tested by means of laser Doppler velocimetry. The velocity pulsation was found to be directly related to the pressure pulsation, while the velocity pulsation was also influenced by the cavitation coefficient. The main frequency of the velocity pulsation was close to the main frequency of the pressure pulsation and became larger as the cavitation factor increased.
- Open Access
Experimental and Numerical Simulation Study on the Flow Characteristics of the Draft Tube in Francis Turbine
The flow characteristics of the draft tube of a Francis turbine have a significant influence on turbine stability. Numerical simulations were performed for a Francis turbine under three different output conditions of 20%, 100%, and 120% at the rated and maximum heads. Laser Doppler velocimetry (LDV) tests were conducted to test the flow characteristics of the draft tube of the Francis turbine model. The flow characteristics in the draft tube, the mechanism of the flow characteristics change, and the effect of the opening on the vortex rope were analyzed. The results showed that the large and invisible vortex in the conical cross-section at the inlet of the draft tube gradually changed to a tangible vortex rope as the guide vane opening (GVO) increased. The pressure and velocity are significantly influenced by the GVO, and the flow characteristics in the draft tube improve as the GVO increases. Simultaneously, the influence range of the vortex rope increased as the head increased.
Open AccessExperimental and Numerical Simulation Study on the Flow Characteristics of the Draft Tube in Francis Turbine
The flow characteristics of the draft tube of a Francis turbine have a significant influence on turbine stability. Numerical simulations were performed for a Francis turbine under three different output conditions of 20%, 100%, and 120% at the rated and maximum heads. Laser Doppler velocimetry (LDV) tests were conducted to test the flow characteristics of the draft tube of the Francis turbine model. The flow characteristics in the draft tube, the mechanism of the flow characteristics change, and the effect of the opening on the vortex rope were analyzed. The results showed that the large and invisible vortex in the conical cross-section at the inlet of the draft tube gradually changed to a tangible vortex rope as the guide vane opening (GVO) increased. The pressure and velocity are significantly influenced by the GVO, and the flow characteristics in the draft tube improve as the GVO increases. Simultaneously, the influence range of the vortex rope increased as the head increased.