Hui Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hui Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
B Xia
1 shared publication- Bin Xia
School of Mechanical Technology, Wuxi Institute of Technology, Wuxi, China
1 shared publication Bin Xu
1 shared publicationDesheng Zhang
1 shared publicationF Y Kong
1 shared publicationFanyu Kong
National Research Center of Pumps, Jiangsu University, Zhenjiang, China
1 shared publication
Latest Publications
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Interaction between non-uniform inflow and rotor–stator interference in a centrifugal pump
An unsteady numerical calculation method was performed to investigate the hydraulic excitation suppression mechanism in volute centrifugal pumps with non-uniform inflow. The propagation characteristics of hydraulic excitation interaction, influence of non-uniform inflow, and rotor–stator interference were systematically analyzed. Results reveal that non-uniform inflow primarily originates from three dominant vertical structures: secondary flow vortices in the elbow inlet, baffle-separated vortices, and high-curvature side-separated vortices. By the way, non-uniform inflow exhibits three periodic pressure peaks within a single rotation cycle: the first from the reverse vortex disturbance of the secondary flow vortices in the elbow inlet pipe, the second from the rotor–stator interaction between the blade trailing edge and the volute tongue; and the third from the flow separation induced by the high-curvature side-separated vortices in the elbow inlet pipe. By adjusting the elbow inlet deflection angle to modulate phase differences between adjacent pressure peaks, mutual energy cancelation was achieved, notably filling the first pressure valley with the second peak. This phase modulation reduced the maximum amplitude of the second peak by up to 33%, effectively suppressing hydraulic excitation and enhancing flow stability. It provides valuable theoretical support for the design and application of centrifugal pumps with non-uniform inflow.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Interaction between non-uniform inflow and rotor–stator interference in a centrifugal pump
An unsteady numerical calculation method was performed to investigate the hydraulic excitation suppression mechanism in volute centrifugal pumps with non-uniform inflow. The propagation characteristics of hydraulic excitation interaction, influence of non-uniform inflow, and rotor–stator interference were systematically analyzed. Results reveal that non-uniform inflow primarily originates from three dominant vertical structures: secondary flow vortices in the elbow inlet, baffle-separated vortices, and high-curvature side-separated vortices. By the way, non-uniform inflow exhibits three periodic pressure peaks within a single rotation cycle: the first from the reverse vortex disturbance of the secondary flow vortices in the elbow inlet pipe, the second from the rotor–stator interaction between the blade trailing edge and the volute tongue; and the third from the flow separation induced by the high-curvature side-separated vortices in the elbow inlet pipe. By adjusting the elbow inlet deflection angle to modulate phase differences between adjacent pressure peaks, mutual energy cancelation was achieved, notably filling the first pressure valley with the second peak. This phase modulation reduced the maximum amplitude of the second peak by up to 33%, effectively suppressing hydraulic excitation and enhancing flow stability. It provides valuable theoretical support for the design and application of centrifugal pumps with non-uniform inflow.
- 26 September 2023
- Published by Elsevier in Ocean Engineering
- Vol. 287
Numerical investigation on the evolution of cavitating dynamics and energy loss around a hydrofoil in fluoroketone under different temperatures
- 26 September 2023
- Published by Elsevier in Ocean Engineering
- Vol. 287
Numerical investigation on the evolution of cavitating dynamics and energy loss around a hydrofoil in fluoroketone under different temperatures
- Open Access
- 18 March 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (3)
Experimental investigation of cavitation characteristics for a high-speed inducer with a great flow rate
Cavitation performance is a key parameter for a mine high-speed rescue pump, which reduces the stability and reliability of the entire unit. In this study, an experimental method was used to investigate the cavitation characteristics of an inducer installed on the impeller upstream. Hydraulic performance without cavitation was determined along with the cavitation performance, and a visualization experiment was implemented. The inducer head slightly decreased when the cavitation number started to decline; however, it dropped significantly thereafter. At 4200 r/min, anti-cavitation ability of the inducer had no connection with the blade numbers. The anti-cavitation performance of the inducer with three blades was superior than that of the inducer with two blades. The law governing shaft power, cavitation number, and rotating speed disagreed with the similarity law theory. Moreover, the inducer efficiency was higher at greater speeds. The evolution of cavitation bubbles was categorized into the inception, developing, and developed stages. When the cavitation number decreased, vortex cavitation was induced along with the tip leakage vortex; subsequently, wedge-shaped sheet cavitation occurred, which was followed by back-flow vortex cavitation. The areas associated with wedge-shape sheet cavitation and back-flow vortex cavitation increased gradually, extending spirally along the axial direction until the entire flow passage was blocked. Overall, the heads declined by 1.1%–1.9% for the inducer with three and two blades, respectively.
- 18 March 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (3)
Open AccessExperimental investigation of cavitation characteristics for a high-speed inducer with a great flow rate
Cavitation performance is a key parameter for a mine high-speed rescue pump, which reduces the stability and reliability of the entire unit. In this study, an experimental method was used to investigate the cavitation characteristics of an inducer installed on the impeller upstream. Hydraulic performance without cavitation was determined along with the cavitation performance, and a visualization experiment was implemented. The inducer head slightly decreased when the cavitation number started to decline; however, it dropped significantly thereafter. At 4200 r/min, anti-cavitation ability of the inducer had no connection with the blade numbers. The anti-cavitation performance of the inducer with three blades was superior than that of the inducer with two blades. The law governing shaft power, cavitation number, and rotating speed disagreed with the similarity law theory. Moreover, the inducer efficiency was higher at greater speeds. The evolution of cavitation bubbles was categorized into the inception, developing, and developed stages. When the cavitation number decreased, vortex cavitation was induced along with the tip leakage vortex; subsequently, wedge-shaped sheet cavitation occurred, which was followed by back-flow vortex cavitation. The areas associated with wedge-shape sheet cavitation and back-flow vortex cavitation increased gradually, extending spirally along the axial direction until the entire flow passage was blocked. Overall, the heads declined by 1.1%–1.9% for the inducer with three and two blades, respectively.
- Open Access
- 20 December 2013
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 52 (2) , 022007
Numerical calculation and optimal design of a hot water circulation pump
The problem of hot water circulation pump head shortage is common. In this paper, numerical simulation technology, combined with orthogonal experimental design, was used to research optimal designs to improve the hot water circulation pump's head. CFX software was used to calculate the flow field in the pump, and the head-flow rate curve could be achieved. The accuracy of CFD was validated through comparison between numerical and experimental data. According to the experience, the number of impeller blades, thickness and width of impeller outlet were changed to improve the hot water circulation pump's head. A three factors and level values of model pump orthogonal experiment was designed, and numerical simulation of whole flow field based on CFX was adopted to implement the orthogonal experiment. Finally, the best designed scheme for model pump was obtained. The analysis of results indicates that the head of hot water circulation pump has increased by 7.77% at rated conditions. The distribution in impellers' internal flow field is symmetrical, and accords with the law of fluids flow in the common centrifugal pump.
- 20 December 2013
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 52 (2) , 022007
Open AccessNumerical calculation and optimal design of a hot water circulation pump
The problem of hot water circulation pump head shortage is common. In this paper, numerical simulation technology, combined with orthogonal experimental design, was used to research optimal designs to improve the hot water circulation pump's head. CFX software was used to calculate the flow field in the pump, and the head-flow rate curve could be achieved. The accuracy of CFD was validated through comparison between numerical and experimental data. According to the experience, the number of impeller blades, thickness and width of impeller outlet were changed to improve the hot water circulation pump's head. A three factors and level values of model pump orthogonal experiment was designed, and numerical simulation of whole flow field based on CFX was adopted to implement the orthogonal experiment. Finally, the best designed scheme for model pump was obtained. The analysis of results indicates that the head of hot water circulation pump has increased by 7.77% at rated conditions. The distribution in impellers' internal flow field is symmetrical, and accords with the law of fluids flow in the common centrifugal pump.