RBRobert W. Bielenberg

Robert W. Bielenberg

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Robert W. Bielenberg has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • MASH Evaluation of Minnesota Department of Transportation Bicycle and Pedestrian Bridge Rail and Hybrid Bridge Rail

    by Brandon Perry, Ronald Faller, Scott Rosenbaugh, Cody Stolle, Robert Bielenberg, Joshua Steelman

    The Minnesota Department of Transportation (MnDOT) currently uses two bridge rail systems that are configured with a concrete bridge rail and a steel beam and post rail. The first is a concrete bridge rail with an attached bicycle and pedestrian rail and the second is a hybrid concrete bridge rail with a lower brush curb and an upper steel beam and post railing structure. Both bridge railings were previously developed and successfully crash tested under the safety criteria of NCHRP Report 350. MnDOT desired to evaluate these bridge railings to the current safety standards of AASHTO’s Manual for Assessing Safety Hardware (MASH). The concrete railing with a bicycle and pedestrian rail was crash tested to MASH TL-3, and it satisfied all safety criteria for MASH test 3-11. The hybrid bridge railing was subjected to all three prescribed crash tests in the MASH TL-4 matrix. The two tests with passenger vehicles were conducted near the downstream end transition to a concrete end buttress to evaluate vehicle snag, while the single-unit truck test was conducted near the middle of the rail to evaluate the railing’s strength. The hybrid railing passed all safety performance criteria.

  • Attaching Steel Bridge Rail Posts Directly to Bridge Decks: Design Procedures, Best Practices, and Case Studies

    by Andrew E. Loken, Scott K. Rosenbaugh, Robert W. Bielenberg, Joshua S. Steelman, Ronald K. Faller

    Steel post-and-beam railings which attach directly to bridge decks are beneficial for a variety of reasons, including reduction of dead weight, unrestricted drainage, aesthetics, and rapid installation. However, because of a long-standing convention holding that the use of steel posts without curbs is likely to result in costly deck damage, steel bridge railings are used less frequently than concrete parapets and curbed steel railings. Under NCHRP Project 12-119, this convention was challenged, and an updated methodology for evaluating/designing bridge decks to support steel posts was developed. The method is compatible with both damage-mitigating and damage-permitting design philosophies. Failure of the deck slab is characterized as a trapezoidal yield-line mechanism, which can be adjusted to account for local punching shear damage below the post. To develop the methodology, in this research a physical impact test was performed on an instrumented steel post and bridge deck specimen. A calibrated LS-DYNA model was then developed and used to create a data pool consisting of simulated pushover tests of parametric variations and in-service railing models from which design guidance was extracted. General guidelines and best practices for attaching steel posts to bridge decks, which are consistent with the updated methodology, are presented in this paper alongside general recommendations for selecting appropriate post sizes for a common bridge deck designs.

  • Evaluation of the Compatibility of Battery Electric Vehicles With Roadside Hardware

    by Robert Bielenberg, Cody Stolle, Ronald Faller, Scott Rosenbaugh, Genevieve Pezzola, Jessica Vankirk

    Battery electric vehicles (BEVs) are rapidly becoming a significant part of the U.S. vehicle fleet. These vehicles possess significant design variations from conventional, gas-powered vehicles, including increased curb weight, altered mass distribution, different frame structures, and altered vehicle geometry that may adversely affect the safety performance of existing roadside hardware. The objective of this research was to perform full-scale crash testing of BEVs with common roadside hardware to identify potential compatibility issues. Four full-scale crash tests were conducted according to American Association of State Highway and Transportation Officials’ Manual for Assessing Safety Hardware (MASH) requirements as part of the study using Telsa Model 3 sedans and Rivian R1T pickup trucks. Testing was performed on the Midwest Guardrail System, a high-performance concrete parapet, and an F-shape portable concrete barrier. Two crash tests on the Midwest Guardrail System failed to meet safety requirements owing to the Telsa Model 3 underriding the guardrail and the Rivian R1T rupturing the guardrail. Full-scale crash testing on the concrete parapet using the Telsa Model 3 resulted in occupant risk criteria that exceeded acceptable limits. Testing on the F-shape portable concrete barrier using the Rivian R1T found that the barrier was able to contain and redirect the vehicle, but the performance of the barrier system was at its functional limit. The crash test results provide insights into the compatibility issues of BEVs with current roadside hardware, and recommendations for research needs and additional actions to address these issues are suggested.


  • Design of Low-Tension Cable Barrier Adjacent to Steep Slopes

    by Robert Bielenberg, Cody Stolle, Ronald Faller

    In the early 2000s, successful crash testing was performed according to the National Cooperative Highway Research Program (NCHRP) Report 350 criteria on a low-tension cable barrier installed adjacent to 1.5H:1V slopes that utilized a 4 ft post spacing and a 4 ft offset from the slope break point (SBP). Recently, the Nebraska Department of Transportation (NDOT) desired to investigate alternative low-tension cable barrier configurations that could satisfy the Manual for Assessing Safety Hardware (MASH) test level 3 (TL-3) impact conditions and potentially improve cost-effectiveness for NDOT. Dynamic component testing of cable posts was conducted as part of the research. Tests were conducted on S3×5.7 steel posts to evaluate the propensity for penetration of a small car vehicle’s floor pan, and floor pan tearing was observed. Subsequent component tests of an HSS3×2×1/8 tubular post alternative mitigated floor pan tearing. Computer simulations were performed to investigate alternative barrier configurations. Various combinations of post spacing, barrier offset, and cable heights were evaluated. It was determined that systems with 3 ft offset from the slope with 4 ft post spacing, or 4 ft offset from the slope with 6 ft post spacing, may perform acceptably according to MASH TL-3 test designation no. 3-11.

  • Installation Guidelines for Midwest Guardrail System on Curbed Roadways for MASH TL-3 Applications

    by Scott K. Rosenbaugh, Robert W. Bielenberg, Ronald K. Faller, Cody S. Stolle

    The objective of this project was to develop installation guidelines for the placement of the Midwest Guardrail System (MGS) in combination with roadside curbs to satisfy the Manual for Assessing Safety Hardware (MASH) Test Level 3 (TL-3). A combination of vehicle trajectory tests, LS-DYNA simulations, and MASH crash testing were used to achieve this objective. Two vehicle trajectory tests, using a 2270P pickup and an 1100C small car, were conducted with the vehicles traversing over a 6 in. tall, American Association of State Highway and Transportation Officials Type B curb at impact conditions consistent with MASH TL-3. The suspensions of LS-DYNA models for these MASH vehicles were updated, and validated to match the vehicle trajectories measured during the curb traversal tests. The updated vehicle models were then used to simulate MASH TL-3 impacts with the MGS set at various offsets behind the curb. An offset of 6 ft was selected as the maximum offset for the MGS behind the curb. Two MASH crash tests were conducted on the MGS placed behind the curb. A MASH 3-11 test was conducted with the MGS offset 6 ft behind a 6 in. curb to evaluate override and instability concerns, while a MASH 3-10 test was conducted with a 1 ft offset to evaluate underride and snag. Both tests passed MASH TL-3 safety performance criteria. Additional simulations showed that reduced impact speeds and angles did not cause any vehicle containment or stability concerns. Thus, the MGS with a height of 31 in. relative to the top of the curb was considered MASH TL-3 crashworthy when installed at offsets between 1 and 6 ft behind a roadside curb.


  • Development of a MASH TL-4 Open Concrete Bridge Rail

    by Scott K. Rosenbaugh, Robert W. Bielenberg, Ronald K. Faller

    A new open concrete bridge rail was developed to satisfy the safety performance criteria of AASHTO’s (American Association of State Highway and Transportation Official’s) Manual for Assessing Safety Hardware (MASH) Test Level 4 (TL-4). The railing design was optimized to minimize vehicle snag, contain large openings for drainage and aesthetics, minimize installation costs, and have the capacity to withstand MASH TL-4 impacts. Additionally, the railing was designed to be crashworthy before and after roadway overlays up to 3 in. thick. The new barrier was designed with a height of 39 in. and a width of 14 in. Posts were 36 in. long, by 10 in. deep, by 12 in. tall, and were set back 4 in. from the face of the railing to minimize the risk of vehicle snag. The inelastic post-and-beam method found in Section 13 of AASHTO LRFD Bridge Design Specifications was modified to account for differences in failure shapes between steel and concrete post and beam railings. The modified method also adjusted the height for the applied design load to match the recommended 30 in. height for tall TL-4 barriers. This modified analysis method was used to optimize the barrier geometry and reinforcement. The new open concrete bridge rail was then subjected to crash testing in accordance with MASH TL-4. All three tests, MASH Tests 4-10, 4-11, and 4-12, resulted in successful capture and safe redirection of the vehicles. Thus, the new open concrete bridge railing was deemed MASH TL-4 crashworthy.


  • Investigation and Evaluation of a MASH TL-4 Precast Concrete Bridge Railing

    by Tewodros Y. Yosef, Ronald K. Faller, Behrouz Shafei, Robert W. Bielenberg, Scott K. Rosenbaugh, Dikshant Saini, Sri Sritharan, Brent Phares, Jennifer D. Rasmussen, Amirhosein Vakili, et al.

    Recently, a precast concrete bridge railing with unique connection details for barrier-to-deck and barrier-to-barrier interfaces was developed at the Institute of Transportation (InTrans)-Iowa State University (ISU). Successful laboratory experiments led to the current study, in which the primary objectives were to determine if the bridge railing system complied with the American Association of State Highway and Transportation Officials (AASHTO) Manual for Assessing Safety Hardware (MASH) Test-Level 4 (TL-4) impact safety standards through a sequence of stages, including pre-crash simulations and one full-scale crash test with a 10000S single-unit truck (SUT). Initial analyses incorporated LS-DYNA computer simulations emulating MASH TL-4 impacts on two prototype barrier configurations: a single-slope shape and a near-vertical shape. These simulations facilitated the discernment of the bridge rail length, reinforcement details, crashworthiness for passenger vehicles, selection of the single-slope shape for crash testing, and determination of a critical impact point for the 10000S SUT crash test. Subsequent modifications to the single-slope barrier system with inclined bar connections were predicated on these computational findings. A full-scale crash test assessed the bridge railing and the loading to the inclined steel anchor bars under MASH test designation no. 4-12, focusing on its impact safety performance and potential damage to the barrier and bridge deck. In test no. ABCBRM-1, the single-unit truck, was successfully contained and redirected, with the barrier and deck sustaining negligible damage, and all safety performance criteria were within acceptable limits as defined in MASH. The study findings demonstrated that the modified single-slope, precast concrete bridge rail system met the MASH TL-4 impact safety criteria.


  • Vehicle Collision Load Design Demands for Deck Overhangs with Parapet Railings

    by Andrew E. Loken, Joshua S. Steelman, Robert W. Bielenberg, Scott K. Rosenbaugh, Ronald K. Faller

    The majority of bridge rails used in the U.S.A. and Canada are solid concrete parapets. However, the design procedure included in the AASHTO LRFD Bridge Design Specifications (BDS) for deck overhangs supporting parapets has not been modified for nearly 50 years. The specifications currently recommend that the deck overhang moment demand is taken as the cantilever bending strength of the parapet at its base. This recommendation results in uneconomical deck designs if the parapet is overdesigned. In this research effort, which was performed under National Cooperative Highway Research Program Project 12-119, the distribution of vehicle impact loads through the parapet and overhang was characterized, new equations were proposed to calculate overhang design demands, and the effect of deck understrength on parapet capacity was quantified. To develop updated design guidance, physical testing of instrumented specimens was performed, and validated LS-DYNA models were used to evaluate a variety of in-service railing and overhang designs. Results indicated that deck moments from lateral vehicle impact loads can be reliably estimated by assuming they distribute at 45 degrees with downward travel through the parapet and at 60 degrees with inward travel through the overhang. These angles are used to calculate effective lengths at critical sections, and overhang design moments are calculated by dividing the total applied moment over these lengths. Distribution of tensile loads was found to be minimal. The overhang design guidance developed in this project, which is currently under review for adoption into the BDS, routinely results in more economical deck designs than the existing method.


  • MASH TL-3 Evaluation of the Hawaii Department of Transportation 34 in. Tall Aesthetic Bridge Rail with Pedestrian Rail and Sidewalk Options

    by Cody Stolle, Robert W. Bielenberg, Ronald K. Faller, Sina Changizian, Dean Takiguchi, Kimberly M. Okamura, James Fu

    Recommended guidelines were provided for the shape and size of aesthetic features added to roadside barriers in National Cooperative Highway Research Program Report No. 554, but limited full-scale crash testing has been performed on barriers with aesthetic features, especially in combination with sidewalks and pedestrian railings, each of which may contribute to increased propensity for vehicle snag, vehicle instabilities, and occupant risk metrics. A Hawaii Department of Transportation (HDOT) bridge rail design with vertical faces and aesthetic recessed panels was evaluated to Manual for Assessing Safety Hardware (MASH) TL-3 impact conditions in three configurations: stand-alone; in combination with a pedestrian handrail installed on the back side of the barrier system; and in combination with a pedestrian rail and 6 ft long x 6 in. tall sidewalk. The 34 in. tall aesthetic concrete bridge rail consisted of segments measuring 11 ft long at upstream and downstream ends and three 22 ft long, consecutive interior segments. MASH test designation Nos. 3-10 and 3-11 were performed on the stand-alone system and with the sidewalk and pedestrian rail, and test designation 3-11 was performed on the system on level terrain with handrail. Results indicated that the HDOT 34 in. tall aesthetic concrete bridge rail was crashworthy in all of the configurations evaluated.

  • Analysis and Evaluation of Slip Base Aluminum Single-Post Sign Supports under Manual for Assessing Safety Hardware Safety Performance Criteria

    by Chen Fang, Joshua S. Steelman, Robert W. Bielenberg, Ronald K. Faller, Brandon J. Perry

    Single-post sign supports are commonly used near to roadways. Signs can assume various configurations, yet few full-scale crash tests have been conducted to date to investigate crash performance of sign supports under current American Association of State Highway and Transportation Officials (AASHTO) Manual for Assessing Safety Hardware (MASH) criteria. This study investigated crash performance for aluminum, slip base, single-post signs under MASH criteria to determine critical configurations and develop prospective assessments of crashworthiness. These systems were supported by a four-bolt slip base and mounted on a 4 in. diameter aluminum post. Two full-scale crash tests were performed to evaluate performance of a system with a 4 × 4 ft sign panel under MASH test Nos. 3-61 and 3-62, in which the slip base activated and released the sign in a predictable manner. Safety concerns for the tested signs were raised by sign penetration through the rear window and excessive roof crush during MASH test No. 3-61. LS-DYNA models were developed and validated against test results. LS-DYNA simulations were conducted on four sign configurations to represent a range of sign panel sizes and design heights to analyze critical characteristics of single-post signs. Simulations were also conducted with increased design height to explore preliminary options for improving the performance of sign supports. Generally, signs with centroid heights at least 10 ft were deemed to have high potential of passing MASH Test Level 3 (TL-3) criteria, but it was recommended that the critical sign configuration be modified to raise the sign cluster centroid from a design height of 9 ft to 11.5 ft or greater.