Meigui Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Meigui Yin has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Jiangqi Long
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou, China
4 shared publicationsHui Qiu
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou, China
2 shared publicationsLongxiang Huang
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou 325035, People’s Republic of China
2 shared publicationsWei Guan
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou, China
2 shared publicationsXingxin Yang
Jinhua Technician College, Jinhua, 321016, People’s Republic of China
2 shared publicationsYue Yang
Jinhua Technician College, Jinhua, 321016, People’s Republic of China
2 shared publications
Latest Publications
- 5 September 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (3) , 035016
Effect of normal load on the tribo-corrosion behaviors of 20CrMnTi alloy steel
Tribo-corrosion behaviors had greatly affected the service performance of 20CrMnTi gear alloy steel. Experimental tests and finite element analysis methods were applied to investigate the influence of normal load on the damage behaviors of 20CrMnTi gear alloy steel under dry and oil-lubricated conditions, respectively. The tribological behaviors, electrochemical corrosion response, and damage evolution rule were discussed in detail. Results showed that the increased of normal load can enhance the tribological damage and electrochemical corrosion degree of 20CrMnTi gear alloy steel under both dry and oil-lubricated conditions. Meanwhile, the aggravating effect in the oil-lubricated condition is lower than that in the dry condition. The main damage mechanisms under dry wear conditions are mainly adhesive wear, abrasive wear, and fatigue spalling. Meanwhile, abrasive wear and pitting corrosion are the main failure mechanisms under oil-lubricated condition.
- 5 September 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (3) , 035016
Effect of normal load on the tribo-corrosion behaviors of 20CrMnTi alloy steel
Tribo-corrosion behaviors had greatly affected the service performance of 20CrMnTi gear alloy steel. Experimental tests and finite element analysis methods were applied to investigate the influence of normal load on the damage behaviors of 20CrMnTi gear alloy steel under dry and oil-lubricated conditions, respectively. The tribological behaviors, electrochemical corrosion response, and damage evolution rule were discussed in detail. Results showed that the increased of normal load can enhance the tribological damage and electrochemical corrosion degree of 20CrMnTi gear alloy steel under both dry and oil-lubricated conditions. Meanwhile, the aggravating effect in the oil-lubricated condition is lower than that in the dry condition. The main damage mechanisms under dry wear conditions are mainly adhesive wear, abrasive wear, and fatigue spalling. Meanwhile, abrasive wear and pitting corrosion are the main failure mechanisms under oil-lubricated condition.
- 15 January 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (1) , 015004
Effect of surface roughness on the fretting corrosion behavior of Inconel 690 alloy tube
Surface roughness which is an important index to evaluate a material’s surface properties, can strongly influence the service performance of steam generator tubes in nuclear power plants. This study used experimental tests and finite element analysis to investigate the fretting corrosion mechanisms of Inconel 690 alloy tubes of three roughness surfaces (Sa ‘Surface Roughness Average’ ≈ 0.09, 0.25, and 0.50 μm) under 25 °C and 100 °C artificial sea water (3.5% NaCl solution) conditions. Results showed that surface roughness affected the fretting damage and electrochemical corrosion behavior of the alloy tubes significantly. This is mainly due to surface roughness also belongs to a kind of micro-defects, which would influence the fretting contact state and corrosive medium effect, and temperature influenced oxidation. All these conditions led to different fretting corrosion damage.
- 15 January 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (1) , 015004
Effect of surface roughness on the fretting corrosion behavior of Inconel 690 alloy tube
Surface roughness which is an important index to evaluate a material’s surface properties, can strongly influence the service performance of steam generator tubes in nuclear power plants. This study used experimental tests and finite element analysis to investigate the fretting corrosion mechanisms of Inconel 690 alloy tubes of three roughness surfaces (Sa ‘Surface Roughness Average’ ≈ 0.09, 0.25, and 0.50 μm) under 25 °C and 100 °C artificial sea water (3.5% NaCl solution) conditions. Results showed that surface roughness affected the fretting damage and electrochemical corrosion behavior of the alloy tubes significantly. This is mainly due to surface roughness also belongs to a kind of micro-defects, which would influence the fretting contact state and corrosive medium effect, and temperature influenced oxidation. All these conditions led to different fretting corrosion damage.
- 14 January 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (6) , 3063-3079
Effect of laser shock peening on the tribo-corrosion behavior of 20CrMnTi alloy steel
- 14 January 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (6) , 3063-3079
Effect of laser shock peening on the tribo-corrosion behavior of 20CrMnTi alloy steel
- 26 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11349-11360
Effect of CrAlTiN Coating on Fretting Wear Behavior of Inconel 690 Alloy in Dry and Seawater Conditions
- 26 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11349-11360
Effect of CrAlTiN Coating on Fretting Wear Behavior of Inconel 690 Alloy in Dry and Seawater Conditions
- 20 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (24) , 14150-14160
Synergistic Effect of Steam and Sand Grains on Sliding Wear Properties of Metal-Impregnated Pantograph Strip
- 20 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (24) , 14150-14160
Synergistic Effect of Steam and Sand Grains on Sliding Wear Properties of Metal-Impregnated Pantograph Strip
- Open Access
- 1 August 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2566 (1) , 012118
The Effect of Temperature and Load on the Current Carrying and Erosion Behavior of Metal-Impregnated Pantograph Strip
As an important current-collecting component of the electric locomotive, the pantograph strip may increase its surface temperature due to catenary vibration, friction heat generation, arc burning, catenary hard spots, and other reasons during actual operation. Given the action of electric current, an electrochemical reaction is unavoidable on the contact surface. Under low voltage DC conditions, the influence of temperature and load on relevant electrical and tribological parameters of the pantograph strip was studied using self-developed multi-functional friction and wear tester and changing forward load, surface temperature, etc. The electrochemical reaction was performed at 3.5 wt% NaCl. The results showed that with the increase in temperature, the initial contact resistance, friction coefficient, wear, and corrosion resistance of the surface material of the sample decreased, and the wear amount increased significantly.
- 1 August 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2566 (1) , 012118
Open AccessThe Effect of Temperature and Load on the Current Carrying and Erosion Behavior of Metal-Impregnated Pantograph Strip
As an important current-collecting component of the electric locomotive, the pantograph strip may increase its surface temperature due to catenary vibration, friction heat generation, arc burning, catenary hard spots, and other reasons during actual operation. Given the action of electric current, an electrochemical reaction is unavoidable on the contact surface. Under low voltage DC conditions, the influence of temperature and load on relevant electrical and tribological parameters of the pantograph strip was studied using self-developed multi-functional friction and wear tester and changing forward load, surface temperature, etc. The electrochemical reaction was performed at 3.5 wt% NaCl. The results showed that with the increase in temperature, the initial contact resistance, friction coefficient, wear, and corrosion resistance of the surface material of the sample decreased, and the wear amount increased significantly.
- 4 April 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (14) , 6313-6328
The fretting tribocorrosion properties of CrAlTiN coating on the Inconel 690 alloy
- 4 April 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (14) , 6313-6328
The fretting tribocorrosion properties of CrAlTiN coating on the Inconel 690 alloy
- 24 May 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10 (2) , 025022
Effect of ultrasonic surface rolling process on the impact wear behavior of Inconel 690 alloy at 25 °C and 300 °C
As an important nuclear power material, Inconel 690 alloy always need to suffer various harsh impact wear behaviors during its service period. Therefore, how to further enhance its surface wear resistance and objectively reveal its fretting wear mechanism under various conditions have vital scientific values for improving its service performance. This study first applies specific ultrasonic surface rolling process (USRP) to treat the Inconel 690 alloy surface with two and four times separately. And then a controllable impact kinetic energy wear test rig is used to comparative investigate the impact wear behaviors of as-received and USRP treated samples at 25 °C and 300 °C temperature. Results indicate that USRP can effectively improve the near surface Nano-hardness, residual compressive stress and other mechanical properties of Inconel 690 alloy, thereby increasing its impact wear resistance. The impact wear mechanism at 25 °C is plastic deformation causes fatigue spalling, and some adhesion wear are found at the 300 °C wear condition.
- 24 May 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10 (2) , 025022
Effect of ultrasonic surface rolling process on the impact wear behavior of Inconel 690 alloy at 25 °C and 300 °C
As an important nuclear power material, Inconel 690 alloy always need to suffer various harsh impact wear behaviors during its service period. Therefore, how to further enhance its surface wear resistance and objectively reveal its fretting wear mechanism under various conditions have vital scientific values for improving its service performance. This study first applies specific ultrasonic surface rolling process (USRP) to treat the Inconel 690 alloy surface with two and four times separately. And then a controllable impact kinetic energy wear test rig is used to comparative investigate the impact wear behaviors of as-received and USRP treated samples at 25 °C and 300 °C temperature. Results indicate that USRP can effectively improve the near surface Nano-hardness, residual compressive stress and other mechanical properties of Inconel 690 alloy, thereby increasing its impact wear resistance. The impact wear mechanism at 25 °C is plastic deformation causes fatigue spalling, and some adhesion wear are found at the 300 °C wear condition.
- 12 November 2021
- Published by ASME International in Journal of Tribology
- Vol. 144 (4) , 1-17
Fretting Wear Behavior of Micro-Arc Oxidation Coating Fabricated on AZ91 Magnesium Alloy
In this study, the effect mechanisms between the fretting wear behavior and properties of micro-arc oxidation (MAO) coatings fabricated by different anodic voltages (AVs) on AZ91 magnesium alloy were investigated. The microstructure and macroscopic mechanical properties of the MAO coatings were analyzed by various characterization means. The evolution rule of fretting wear behaviors was carried out through sliding fretting wear experiment under different test parameters. The results showed that the increase in AV increased the MAO coating surface roughness and elastic modulus. The fretting wear resistance of magnesium alloy also enhanced after treatment by MAO, and the improvement effect was positively correlated to AV. Further studies revealed that the wear mechanisms of AZ91 magnesium alloy were oxidation wear and fatigue spalling, and that of MAO coating was mixed abrasive wear and fatigue spalling.
- 12 November 2021
- Published by ASME International in Journal of Tribology
- Vol. 144 (4) , 1-17
Fretting Wear Behavior of Micro-Arc Oxidation Coating Fabricated on AZ91 Magnesium Alloy
In this study, the effect mechanisms between the fretting wear behavior and properties of micro-arc oxidation (MAO) coatings fabricated by different anodic voltages (AVs) on AZ91 magnesium alloy were investigated. The microstructure and macroscopic mechanical properties of the MAO coatings were analyzed by various characterization means. The evolution rule of fretting wear behaviors was carried out through sliding fretting wear experiment under different test parameters. The results showed that the increase in AV increased the MAO coating surface roughness and elastic modulus. The fretting wear resistance of magnesium alloy also enhanced after treatment by MAO, and the improvement effect was positively correlated to AV. Further studies revealed that the wear mechanisms of AZ91 magnesium alloy were oxidation wear and fatigue spalling, and that of MAO coating was mixed abrasive wear and fatigue spalling.
- Open Access
- 19 October 2021
- Published by Tsinghua University Press in Friction
- Vol. 10 (3) , 473-490
Impact-sliding wear response of 2.25Cr1Mo steel tubes: Experimental and semi-analytical method
The impact-sliding wear behavior of steam generator tubes in nuclear power plants is complex owing to the dynamic nature of the mechanical response and self-induced tribological changes. In this study, the effects of impact and sliding velocity on the impact-sliding wear behavior of a 2.25Cr1Mo steel tube are investigated experimentally and numerically. In the experimental study, a wear test rig that can measure changes in the impact and friction forces as well as the compressive displacement over different wear cycles, both in real time, is designed. A semi-analytical model based on the Archard wear law and Hertz contact theory is used to predict wear. The results indicate that the impact dynamic effect by the impact velocity is more significant than that of the sliding velocity, and that both velocities affect the friction force and wear degree. The experimental results for the wear depth evolution agree well with the corresponding simulation predictions.
- 19 October 2021
- Published by Tsinghua University Press in Friction
- Vol. 10 (3) , 473-490
Open AccessImpact-sliding wear response of 2.25Cr1Mo steel tubes: Experimental and semi-analytical method
The impact-sliding wear behavior of steam generator tubes in nuclear power plants is complex owing to the dynamic nature of the mechanical response and self-induced tribological changes. In this study, the effects of impact and sliding velocity on the impact-sliding wear behavior of a 2.25Cr1Mo steel tube are investigated experimentally and numerically. In the experimental study, a wear test rig that can measure changes in the impact and friction forces as well as the compressive displacement over different wear cycles, both in real time, is designed. A semi-analytical model based on the Archard wear law and Hertz contact theory is used to predict wear. The results indicate that the impact dynamic effect by the impact velocity is more significant than that of the sliding velocity, and that both velocities affect the friction force and wear degree. The experimental results for the wear depth evolution agree well with the corresponding simulation predictions.