Afshan Khaleghi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Afshan Khaleghi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
David Risk
11 shared publications- Mathias Göckede
Max Planck Institute for Biogeochemistry, Jena, Germany
7 shared publications - Evelise Bourlon
St. Francis Xavier University
6 shared publications Nicholas Nickerson
Eosense Inc, Nova Scotia, Canada
6 shared publicationsMartin Lavoie
3 shared publications- Andrea Darlington
Air Quality Research Division, Environment and Climate Change Canada, Toronto, ON, Canada
2 shared publications
Latest Publications
- Open Access
- 14 March 2026
- Published by Copernicus GmbH
Truck-Based Methane Detection, Attribution, and Quantification in Upstream Oil and Gas: Controlled Release Validation and Field Case Study
The oil and gas (O&G) sector is a significant source of global anthropogenic methane (CH4) emissions, prompting increased regulatory oversight and the rapid development of new methane measurement and mitigation technologies. While screening technologies such as optical gas imaging (OGI) are widely used for regulatory compliance due to their ability to visually identify component-level leaks, there is emerging evidence from regulatory effectiveness studies in Canada that OGI surveys do not detect all sources, with remote sensing surveys often identifying significantly higher site-level emissions. Complementary methods with low detection thresholds may be necessary to improve regulatory compliance and fully represent low-level emission distributions in measurement inventories. In this study, we characterize the performance of a truck-based measurement system using controlled release data, and present results from a field case study in which this method was applied alongside aerial LiDAR and quantitative OGI surveys.Truck-based measurement systems are a relatively inexpensive and efficient option for site-level screening and emission quantification. This method integrates a vehicle-mounted gas analyzer, anemometer, and GPS to collect atmospheric CH4 concentrations and wind characteristics along the driven route. This data is processed via an automated framework in which CH4 plumes are identified, attributed to a source based on wind characteristics and source geometry, and quantified using a Gaussian plume dispersion model. We assess detection, attribution, and quantification performance using data collected by Eotrac Incorporated during controlled release experiments (0.025 - 11 kg/h) at test sites simulating realistic O&G emission scenarios. While release rates and locations were blind to the measurement team during testing, the analysis presented here was conducted after the releases were unblinded.The truck-based system achieved a true positive detection rate exceeding 95 % with no false positives. We find that increasing the number of downwind measurement transects can significantly reduce the 90 % detection limit, from 0.45 kg/h with one transect to 0.03 kg/h with five transects. During single-source release scenarios, source attribution accuracy was 100 % at the facility level, 99.7 % at the equipment group-level, and 50 % at the individual source-level, indicating strong performance for identifying emitting equipment groups (7-15 m radius) despite challenges in pinpointing exact leak locations.In the field case study, the site-level emission frequency was 74.3 % for the truck-based method, compared to 8.6 % for QOGI and 31.8 % for aerial LiDAR. This suggests that OGI misses a significant fraction of emitting sites. Truck-based methods therefore offer a reliable complement to existing detection approaches and have the potential to improve both regulatory compliance and the representation of low-level emitters in inventories.
- 14 March 2026
- Published by Copernicus GmbH
Open AccessTruck-Based Methane Detection, Attribution, and Quantification in Upstream Oil and Gas: Controlled Release Validation and Field Case Study
The oil and gas (O&G) sector is a significant source of global anthropogenic methane (CH4) emissions, prompting increased regulatory oversight and the rapid development of new methane measurement and mitigation technologies. While screening technologies such as optical gas imaging (OGI) are widely used for regulatory compliance due to their ability to visually identify component-level leaks, there is emerging evidence from regulatory effectiveness studies in Canada that OGI surveys do not detect all sources, with remote sensing surveys often identifying significantly higher site-level emissions. Complementary methods with low detection thresholds may be necessary to improve regulatory compliance and fully represent low-level emission distributions in measurement inventories. In this study, we characterize the performance of a truck-based measurement system using controlled release data, and present results from a field case study in which this method was applied alongside aerial LiDAR and quantitative OGI surveys.Truck-based measurement systems are a relatively inexpensive and efficient option for site-level screening and emission quantification. This method integrates a vehicle-mounted gas analyzer, anemometer, and GPS to collect atmospheric CH4 concentrations and wind characteristics along the driven route. This data is processed via an automated framework in which CH4 plumes are identified, attributed to a source based on wind characteristics and source geometry, and quantified using a Gaussian plume dispersion model. We assess detection, attribution, and quantification performance using data collected by Eotrac Incorporated during controlled release experiments (0.025 - 11 kg/h) at test sites simulating realistic O&G emission scenarios. While release rates and locations were blind to the measurement team during testing, the analysis presented here was conducted after the releases were unblinded.The truck-based system achieved a true positive detection rate exceeding 95 % with no false positives. We find that increasing the number of downwind measurement transects can significantly reduce the 90 % detection limit, from 0.45 kg/h with one transect to 0.03 kg/h with five transects. During single-source release scenarios, source attribution accuracy was 100 % at the facility level, 99.7 % at the equipment group-level, and 50 % at the individual source-level, indicating strong performance for identifying emitting equipment groups (7-15 m radius) despite challenges in pinpointing exact leak locations.In the field case study, the site-level emission frequency was 74.3 % for the truck-based method, compared to 8.6 % for QOGI and 31.8 % for aerial LiDAR. This suggests that OGI misses a significant fraction of emitting sites. Truck-based methods therefore offer a reliable complement to existing detection approaches and have the potential to improve both regulatory compliance and the representation of low-level emitters in inventories.
- Open Access
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Reply on RC3
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Open AccessReply on RC3
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Reply on RC2
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Open AccessReply on RC2
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Reply on CC1
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 6 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Open AccessReply on CC1
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 19 June 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Comment on egusphere-2025-644
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 19 June 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Open AccessComment on egusphere-2025-644
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 16 June 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Comment on egusphere-2025-644
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 16 June 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-27
Open AccessComment on egusphere-2025-644
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 3 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-27
Optimizing Methane Emission Source Localization in Oil and Gas Facilities Using Lagrangian Stochastic Models and Gradient-Based Detection Tools
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- 3 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-27
Open AccessOptimizing Methane Emission Source Localization in Oil and Gas Facilities Using Lagrangian Stochastic Models and Gradient-Based Detection Tools
Oil and gas facilities are responsible for approximately 35 % of global emissions of methane (CH4), a potent greenhouse gas, posing significant environmental and regulatory challenges. While Continuous Emission Monitoring Systems (CEMS) are widely implemented to track real-time emissions, their effectiveness in localizing specific CH4 emission sources remains limited, particularly under complex environmental conditions. This study integrates CEMS technologies with a Lagrangian Stochastic Back-Trajectory Model, along with an automated Gradient Indicator (GI) tool to improve methane source localization accuracy in oil and gas settings. The model was then applied to a real-world gas distribution site to validate its performance in accurately localizing methane emissions under operational conditions. Using synthetic data simulations, we evaluated the performance of this integrated system under various atmospheric stability conditions, sensor-source height differences, and source proximity. Our results indicate that this combined approach significantly enhances localization performance, achieving a 90 % probability of detection (POD) within a 25–75 meter source-sensor distance under optimal conditions. However, detection performance varied across configurations, with false positive rates (FPF) ranging from 22 % to 86 %, and localization accuracy (LA) ranging from 14 % to 78 %, depending on atmospheric stability, source-sensor geometry, and height differences. The Localization Accuracy (LA) improves when sensor placements are exactly downwind of the emission sources (alignment). The system meets Canadian regulatory requirements for CEMS applications by maintaining localization accuracy above 90 % for unstable and slightly neutral atmospheric conditions, ensuring that emissions are correctly attributed. However, neutral atmospheric conditions and large height differentials between sensors and sources reduce localization accuracy, making optimized sensor configurations important. Findings of the research can be useful for upgrading CEMS systems and help them to overcome some difficulties from regulations associated with methane emission reporting and mitigation efforts.
- Open Access
- 4 May 2025
- Published by California Digital Library (CDL) in EarthArXiv
Most Landfill Methane Emissions Escape Detection in EPA21 Surface Emission Monitoring Surveys
We measured emissions from ten landfills using mobile surveys and Surface Emission Monitoring (SEM) to determine what fraction of emissions that be identified by SEM surveys. Using mobile methane measurements and a back-trajectory attribution and rate estimation method, we measured overall site emissions and those of individual landfill components (active face, closed cells, leachate, etc). We evaluated each component’s contribution to the total emissions and compared how much of emissions captured by mobile surveys could be covered by the walking SEM survey. We found that SEM was effective for closed sites, achieving on-average 67% rate coverage. However, SEM missed relevant emission sources at open landfill sites, most notably from the active face, reducing its rate percent coverage to 17%. The limited rate coverage of SEM suggests that using SEM alone is insufficient for measurement-informed management of landfill emissions. We recommend that SEM be augmented by other methods to fill monitoring gaps and provide a more comprehensive assessment of landfill methane emissions.
- 4 May 2025
- Published by California Digital Library (CDL) in EarthArXiv
Open AccessMost Landfill Methane Emissions Escape Detection in EPA21 Surface Emission Monitoring Surveys
We measured emissions from ten landfills using mobile surveys and Surface Emission Monitoring (SEM) to determine what fraction of emissions that be identified by SEM surveys. Using mobile methane measurements and a back-trajectory attribution and rate estimation method, we measured overall site emissions and those of individual landfill components (active face, closed cells, leachate, etc). We evaluated each component’s contribution to the total emissions and compared how much of emissions captured by mobile surveys could be covered by the walking SEM survey. We found that SEM was effective for closed sites, achieving on-average 67% rate coverage. However, SEM missed relevant emission sources at open landfill sites, most notably from the active face, reducing its rate percent coverage to 17%. The limited rate coverage of SEM suggests that using SEM alone is insufficient for measurement-informed management of landfill emissions. We recommend that SEM be augmented by other methods to fill monitoring gaps and provide a more comprehensive assessment of landfill methane emissions.
- Open Access
- 5 April 2025
- Published by California Digital Library (CDL) in EarthArXiv
Active Face Emissions: An Opportunity for Reducing Methane Emissions in Global Waste Management
This study used mobile surveys of ten Canadian landfills to assess how methane emissions varied across different landfill sources and operational conditions. The studied landfills included two closed landfills, four open landfills equipped with Gas Collection and Control Systems (GCCS), and four open landfills operating without GCCS. We employed the Gaussian dispersion model to estimate emissions fluxes using on site and off site transect data. We observed high spatial variability of methane emissions and identified the sources that contributed significantly to overall landfill emissions, sources such as the active face, closed cells, compost areas, leachate systems, and GCCS. Overall, we found that the active face of landfills is a major emitter of methane, contributing 76% of the methane emissions for landfills with GCCS and 38% for landfills without GCCS. The results underscore the importance of improved monitoring and management strategies at landfill active faces to more effectively mitigate methane emissions from landfills.
- 5 April 2025
- Published by California Digital Library (CDL) in EarthArXiv
Open AccessActive Face Emissions: An Opportunity for Reducing Methane Emissions in Global Waste Management
This study used mobile surveys of ten Canadian landfills to assess how methane emissions varied across different landfill sources and operational conditions. The studied landfills included two closed landfills, four open landfills equipped with Gas Collection and Control Systems (GCCS), and four open landfills operating without GCCS. We employed the Gaussian dispersion model to estimate emissions fluxes using on site and off site transect data. We observed high spatial variability of methane emissions and identified the sources that contributed significantly to overall landfill emissions, sources such as the active face, closed cells, compost areas, leachate systems, and GCCS. Overall, we found that the active face of landfills is a major emitter of methane, contributing 76% of the methane emissions for landfills with GCCS and 38% for landfills without GCCS. The results underscore the importance of improved monitoring and management strategies at landfill active faces to more effectively mitigate methane emissions from landfills.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
Mitigating Methane Emissions: A Comprehensive Measurement Study of Canadian Landfills
Canada’s waste sector contributes 23% toward national methane emission totals. Recently Canada committed to a 50% reduction in waste sector methane emissions by 2030 from 2020 levels, as part of its Global Methane Pledge action plan. Achieving this ambitious goal will certainty requires that regulators to be armed with an accurate and measurement-informed understanding of landfill methane emissions. In 2022 we carried out a snapshot methane emissions quantification campaign targeting 125 landfills across Canada, followed in 2023 by more detailed source-level measurements across seasons at selected landfills in various climate zones. Snapshot measurements were carried out by vehicle-based surveying coupled with Gaussian and Lagrangian flux inversion, and aircraft mass balance measurements. Repeating source-based measurements were conducted in 2023 across seasons at 12 landfills for 3 climatic regions using vehicle-based surveys, stationary tripod deployments, and drone measurements of plumes, from on-site and off-site locations. Source-specific flux rates were generated based on triangulation, Lagrangian backtrajectory analysis, and a Gaussian dispersion model, and were assessed for magnitude and temporal variability. In snapshot measurement campaigns across the country, we saw generally good agreement between aircraft mass balance and truck measurements, with a moderate but consistent low bias in the truck emission rate estimates. Lagrangian methods to derive flux rate were comparable as long as input data was limited to exclude highly enriched onsite samples. Throughout a varied population of landfills across Canada, we found that emission rate estimates from measurement campaigns were generally in-line with operator-submitted values to the Canadian Greenhouse Gas Reporting Program, whereas a First Order Decay model used by the federal government for planning purposes tended to over-estimate landfill emissions. Climate zone was a clear predictor of methane generated per waste in place. In more detailed source studies, we found that numerous features on landfill operations could emit methane, most expected, but some unexpected. Management practice was a strong predictor of whether source types emitted significantly, or not. Meteorology and seasonal changes in climate were also strong predictor of emissions over time. These large-scale studies provide a wealth of data upon which Canada can base regulatory development and will be beneficial to countries with similar waste sector patterns and climates.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessMitigating Methane Emissions: A Comprehensive Measurement Study of Canadian Landfills
Canada’s waste sector contributes 23% toward national methane emission totals. Recently Canada committed to a 50% reduction in waste sector methane emissions by 2030 from 2020 levels, as part of its Global Methane Pledge action plan. Achieving this ambitious goal will certainty requires that regulators to be armed with an accurate and measurement-informed understanding of landfill methane emissions. In 2022 we carried out a snapshot methane emissions quantification campaign targeting 125 landfills across Canada, followed in 2023 by more detailed source-level measurements across seasons at selected landfills in various climate zones. Snapshot measurements were carried out by vehicle-based surveying coupled with Gaussian and Lagrangian flux inversion, and aircraft mass balance measurements. Repeating source-based measurements were conducted in 2023 across seasons at 12 landfills for 3 climatic regions using vehicle-based surveys, stationary tripod deployments, and drone measurements of plumes, from on-site and off-site locations. Source-specific flux rates were generated based on triangulation, Lagrangian backtrajectory analysis, and a Gaussian dispersion model, and were assessed for magnitude and temporal variability. In snapshot measurement campaigns across the country, we saw generally good agreement between aircraft mass balance and truck measurements, with a moderate but consistent low bias in the truck emission rate estimates. Lagrangian methods to derive flux rate were comparable as long as input data was limited to exclude highly enriched onsite samples. Throughout a varied population of landfills across Canada, we found that emission rate estimates from measurement campaigns were generally in-line with operator-submitted values to the Canadian Greenhouse Gas Reporting Program, whereas a First Order Decay model used by the federal government for planning purposes tended to over-estimate landfill emissions. Climate zone was a clear predictor of methane generated per waste in place. In more detailed source studies, we found that numerous features on landfill operations could emit methane, most expected, but some unexpected. Management practice was a strong predictor of whether source types emitted significantly, or not. Meteorology and seasonal changes in climate were also strong predictor of emissions over time. These large-scale studies provide a wealth of data upon which Canada can base regulatory development and will be beneficial to countries with similar waste sector patterns and climates.