Marie Bøe Henriksen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marie Bøe Henriksen has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Adriënne Esmeralda Oudijk
Department of Engineering Cybernetics, Norwegian University of Science and Technology, NTNU, 7034 Trondheim, Norway
3 shared publications - Fermin Navarro-Medina
Universidad Politéchnica de Madrid, IDR/UPM, Plaza Cardenal Cisneros 3, 28040 Madrid, Spain
3 shared publications - Tor Arne Johansen
Norwegian University of Science and Technology
3 shared publications - Roger Birkeland
Norwegian University of Science and Technology (NTNU)
2 shared publications - Sivert Bakken
SINTEF Ocean AS, Trondheim, Norway
2 shared publications Tor Arne Johansen
Department of Engineering Cybernetics, Norwegian University of Science and Technology, Trondheim, Norway
2 shared publications
Latest Publications
- Open Access
- 1 October 2024
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 18 (04) , 047503-12
Performance comparison of COTS-based hyperspectral imagers using detailed point spread function measurements
Hyperspectral imaging is a rapidly growing field that utilizes a diverse range of camera designs. It has been demonstrated that hyperspectral cameras can be constructed from commercial off-the-shelf (COTS) components, offering the potential for low-cost and widespread use. However, these COTS-based systems may face performance limitations due to optics not being optimized for hyperspectral purposes. Characterizing and comparing the performance of hyperspectral cameras is complex, a challenge recognized by the ongoing development of the IEEE P4001 standard. Specifically, the spatial coregistration among different spectral bands is crucial for the quality and integrity of the recorded spectra in each pixel. The proper evaluation of coregistration and resolution necessitates the measurement of the point spread function for each band. We use measurements of the full 2D sampling point spread function (SPSF) to compare the performance of two hyperspectral imagers (HSIs) built from COTS components: the engineering model of the hyperspectral camera onboard the Hyperspectral Cubesat for Ocean Observation-1 cubesat and an extremely compact HSI developed for drone flights. In addition, the line spread functions across and along the track, keystone distortion, and coregistration errors are derived from the SPSFs. A simplified measurement scheme is also tried and found to provide fair accuracy for the tested cameras. The results highlight the importance of measuring the spatial SPSF for characterizing and comparing different hyperspectral cameras. Results also show that good spectral integrity can be achieved through spatial binning, which of course requires a tradeoff against spatial resolution. Nonetheless, it is evident that such low-cost systems can offer useful capabilities.
- 1 October 2024
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 18 (04) , 047503-12
Open AccessPerformance comparison of COTS-based hyperspectral imagers using detailed point spread function measurements
Hyperspectral imaging is a rapidly growing field that utilizes a diverse range of camera designs. It has been demonstrated that hyperspectral cameras can be constructed from commercial off-the-shelf (COTS) components, offering the potential for low-cost and widespread use. However, these COTS-based systems may face performance limitations due to optics not being optimized for hyperspectral purposes. Characterizing and comparing the performance of hyperspectral cameras is complex, a challenge recognized by the ongoing development of the IEEE P4001 standard. Specifically, the spatial coregistration among different spectral bands is crucial for the quality and integrity of the recorded spectra in each pixel. The proper evaluation of coregistration and resolution necessitates the measurement of the point spread function for each band. We use measurements of the full 2D sampling point spread function (SPSF) to compare the performance of two hyperspectral imagers (HSIs) built from COTS components: the engineering model of the hyperspectral camera onboard the Hyperspectral Cubesat for Ocean Observation-1 cubesat and an extremely compact HSI developed for drone flights. In addition, the line spread functions across and along the track, keystone distortion, and coregistration errors are derived from the SPSFs. A simplified measurement scheme is also tried and found to provide fair accuracy for the tested cameras. The results highlight the importance of measuring the spatial SPSF for characterizing and comparing different hyperspectral cameras. Results also show that good spectral integrity can be achieved through spatial binning, which of course requires a tradeoff against spatial resolution. Nonetheless, it is evident that such low-cost systems can offer useful capabilities.
- Open Access
- 6 November 2023
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 173
Structural thermal optical performance (STOP) analysis and experimental verification of an hyperspectral imager for the HYPSO CubeSat
- 6 November 2023
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 173
Open AccessStructural thermal optical performance (STOP) analysis and experimental verification of an hyperspectral imager for the HYPSO CubeSat
- Open Access
- 20 June 2023
- Published by Springer Nature in CEAS Space Journal
- Vol. 16 (4) , 393-409
Experimental set-up of a thermal vacuum chamber for thermal model in-house correlation and characterization of the HYPSO hyperspectral imager
Space environment with changing temperatures and vacuum can affect the performance of optics instruments onboard satellites. Thermal models and tests are typically done to understand the optics performance within large space projects, but less often in nanosatellites projects. It is even more rarer for an optics payload inside a CubeSat platform, made by a third provider, to do functional tests on their optics during space environment test campaign. In this research, an in-house made vacuum chamber with the possibility to warm up (TVAC) the devices under tests, and wall-through transparency for optics experiments is set-up. In parallel, a thermal model of the HYPerspectral Small satellite for ocean Observation (HYPSO) Hyperspectral Imager (HSI) is developed. The HSI, which is a transmissive grating hyperspectral instrument ranged in the visible to near infrared wavelength, has been tested in TVAC. As thermal control is based on heating the device under test, a new method for fitting the thermal models inside vacuum chambers with only heating capability is proposed. Finally, the TVAC set-up and the thermal model fitting method have been demonstrated to be appropriate to validate the HSI thermal model, and to characterize the optics performance of HSI in vacuum and in the range of temperatures found inside the in-orbit HYPSO-1 CubeSat.
- 20 June 2023
- Published by Springer Nature in CEAS Space Journal
- Vol. 16 (4) , 393-409
Open AccessExperimental set-up of a thermal vacuum chamber for thermal model in-house correlation and characterization of the HYPSO hyperspectral imager
Space environment with changing temperatures and vacuum can affect the performance of optics instruments onboard satellites. Thermal models and tests are typically done to understand the optics performance within large space projects, but less often in nanosatellites projects. It is even more rarer for an optics payload inside a CubeSat platform, made by a third provider, to do functional tests on their optics during space environment test campaign. In this research, an in-house made vacuum chamber with the possibility to warm up (TVAC) the devices under tests, and wall-through transparency for optics experiments is set-up. In parallel, a thermal model of the HYPerspectral Small satellite for ocean Observation (HYPSO) Hyperspectral Imager (HSI) is developed. The HSI, which is a transmissive grating hyperspectral instrument ranged in the visible to near infrared wavelength, has been tested in TVAC. As thermal control is based on heating the device under test, a new method for fitting the thermal models inside vacuum chambers with only heating capability is proposed. Finally, the TVAC set-up and the thermal model fitting method have been demonstrated to be appropriate to validate the HSI thermal model, and to characterize the optics performance of HSI in vacuum and in the range of temperatures found inside the in-orbit HYPSO-1 CubeSat.
- Open Access
- 28 January 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (3) , 755
HYPSO-1 CubeSat: First Images and In-Orbit Characterization
The HYPSO-1 satellite, a 6U CubeSat carrying a hyperspectral imager, was launched on 13 January 2022, with the Goal of imaging ocean color in support of marine research. This article describes the development and current status of the mission and payload operations, including examples of agile planning, captures with low revisit time and time series acquired during a campaign. The in-orbit performance of the hyperspectral instrument is also characterized. The usable spectral range of the instrument is in the range of 430 nm to 800 nm over 120 bands after binning during nominal captures. The spatial resolvability is found empirically to be below 2.2 pixels in terms of Full-Width at Half-Maximum (FWHM) at 565 nm. This measure corresponds to an inherent ground resolvable resolution of 142 m across-track for close to nadir capture. In the across-track direction, there are 1216 pixels available, which gives a swath width of 70 km. However, the 684 center pixels are used for nominal captures. With the nominal pixels used in the across-track direction, the nadir swath-width is 40 km. The spectral resolution in terms of FWHM is estimated to be close to 5 nm at the center wavelength of 600 nm, and the Signal-to-Noise Ratio (SNR) is evaluated to be greater than 300 at 450 nm to 500 nm for Top-of-Atmosphere (ToA) signals. Examples of images from the first months of operations are also shown.
- 28 January 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (3) , 755
Open AccessHYPSO-1 CubeSat: First Images and In-Orbit Characterization
The HYPSO-1 satellite, a 6U CubeSat carrying a hyperspectral imager, was launched on 13 January 2022, with the Goal of imaging ocean color in support of marine research. This article describes the development and current status of the mission and payload operations, including examples of agile planning, captures with low revisit time and time series acquired during a campaign. The in-orbit performance of the hyperspectral instrument is also characterized. The usable spectral range of the instrument is in the range of 430 nm to 800 nm over 120 bands after binning during nominal captures. The spatial resolvability is found empirically to be below 2.2 pixels in terms of Full-Width at Half-Maximum (FWHM) at 565 nm. This measure corresponds to an inherent ground resolvable resolution of 142 m across-track for close to nadir capture. In the across-track direction, there are 1216 pixels available, which gives a swath width of 70 km. However, the 684 center pixels are used for nominal captures. With the nominal pixels used in the across-track direction, the nadir swath-width is 40 km. The spectral resolution in terms of FWHM is estimated to be close to 5 nm at the center wavelength of 600 nm, and the Signal-to-Noise Ratio (SNR) is evaluated to be greater than 300 at 450 nm to 500 nm for Top-of-Atmosphere (ToA) signals. Examples of images from the first months of operations are also shown.
- Open Access
- 14 September 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (18) , 4584
Pre-Launch Assembly, Integration, and Testing Strategy of a Hyperspectral Imaging CubeSat, HYPSO-1
Assembly, Integration, and Verification/Testing (AIV or AIT) is a standardized guideline for projects to ensure consistency throughout spacecraft development phases. The goal of establishing such a guideline is to assist in planning and executing a successful mission. While AIV campaigns can help reduce risk, they can also take years to complete and be prohibitively costly for smaller new space programs, such as university CubeSat teams. This manuscript outlines a strategic approach to the traditional space industry AIV campaign through demonstration with a 6U CubeSat mission. The HYPerspectral Smallsat for Ocean observation (HYPSO-1) mission was developed by the Norwegian University of Science and Technology’s (NTNU) SmallSatellite Laboratory in conjunction with NanoAvionics (the platform provider). The approach retains critical milestones of traditional AIV, outlines tailored testing procedures for the custom-built hyperspectral imager, and provides suggestions for faster development. A critical discussion of de-risking and design-driving decisions, such as imager configuration and machining custom parts, highlights the consequences that helped, or alternatively hindered, development timelines. This AIV approach has proven key for HYPSO-1’s success, defining further development within the lab (e.g., already with the second-generation, HYPSO-2), and can be scaled to other small spacecraft programs throughout the new space industry.
- 14 September 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (18) , 4584
Open AccessPre-Launch Assembly, Integration, and Testing Strategy of a Hyperspectral Imaging CubeSat, HYPSO-1
Assembly, Integration, and Verification/Testing (AIV or AIT) is a standardized guideline for projects to ensure consistency throughout spacecraft development phases. The goal of establishing such a guideline is to assist in planning and executing a successful mission. While AIV campaigns can help reduce risk, they can also take years to complete and be prohibitively costly for smaller new space programs, such as university CubeSat teams. This manuscript outlines a strategic approach to the traditional space industry AIV campaign through demonstration with a 6U CubeSat mission. The HYPerspectral Smallsat for Ocean observation (HYPSO-1) mission was developed by the Norwegian University of Science and Technology’s (NTNU) SmallSatellite Laboratory in conjunction with NanoAvionics (the platform provider). The approach retains critical milestones of traditional AIV, outlines tailored testing procedures for the custom-built hyperspectral imager, and provides suggestions for faster development. A critical discussion of de-risking and design-driving decisions, such as imager configuration and machining custom parts, highlights the consequences that helped, or alternatively hindered, development timelines. This AIV approach has proven key for HYPSO-1’s success, defining further development within the lab (e.g., already with the second-generation, HYPSO-2), and can be scaled to other small spacecraft programs throughout the new space industry.
- Open Access
- 27 March 2022
- Published by Copernicus GmbH
Potential of SIOS’s airborne imaging sensors in Svalbard
Svalbard Integrated Arctic Earth Observing System (SIOS) is an international partnership of 26 scientific institutions from 9 countries studying the environment and climate in and around Svalbard. The key aims of SIOS are: (1) to develop an efficient observing system, (2) to share technology, experience, and data, (3) to close knowledge gaps, and (4) to decrease the environmental footprint of science. SIOS encourages the usage of airborne remote sensing platforms for research activities in Svalbard to complement in situ measurements and reduce the environmental footprint of research. SIOS member institution Norwegian Research Centre (NORCE) has installed and tested a suite of optical imaging sensors on the Lufttransport Dornier aircraft stationed in Longyearbyen as part of the SIOS-InfraNor project. Two optical sensors are installed onboard the Dornier aircraft (1) the PhaseOne IXU-180 RGB camera and (2) the HySpex VNIR-1800 hyperspectral sensor. The aircraft with these cameras is configured to acquire aerial RGB imagery and hyperspectral remote sensing data in addition to its regular transport operation in Svalbard. To date, SIOS has supported around 50 hours of flight time to acquire airborne data using Dornier aircraft in Svalbard for more than 20 scientific projects. Airborne imaging sensors include a variety of applications within glaciology, biology, hydrology, and other fields of Earth system science to understand the state of the environment of Svalbard. Mapping glacier crevasses, generating DEMs for glaciological applications, mapping and characterising earth (e.g., minerals, vegetation), ice (e.g., sea ice, icebergs, glaciers and snow cover) and ocean surface features (e.g. colour, chlorophyll) are examples of implementation. Aerial photos are also useful for monitoring the seasonal changes in snow, sea ice cover, and ocean colour. In 2021, SIOS conducted capacity building activities to train the next generation of polar scientists to use airborne imaging sensor data for their projects as part of the SIOS hyperspectral remote sensing training course (HSRS). This study presents a few selected applications from this course to demonstrate the potential of airborne imaging sensors in Svalbard. These include mapping water bodies (e.g. fjords, rivers), estimation of snow grain size, land cover classification, deriving chlorophyll, and mapping terrestrial vegetation. Preliminary results from these studies will be used to develop operational scientific applications and complement measurements from in-situ observations acquired by SIOS infrastructure in Svalbard. Eventually, these datasets will be valuable resources for calibration and validation activities for upcoming satellite hyperspectral missions, for example, the Copernicus Hyperspectral Imaging Mission for the Environment (CHIME).
- 27 March 2022
- Published by Copernicus GmbH
Open AccessPotential of SIOS’s airborne imaging sensors in Svalbard
Svalbard Integrated Arctic Earth Observing System (SIOS) is an international partnership of 26 scientific institutions from 9 countries studying the environment and climate in and around Svalbard. The key aims of SIOS are: (1) to develop an efficient observing system, (2) to share technology, experience, and data, (3) to close knowledge gaps, and (4) to decrease the environmental footprint of science. SIOS encourages the usage of airborne remote sensing platforms for research activities in Svalbard to complement in situ measurements and reduce the environmental footprint of research. SIOS member institution Norwegian Research Centre (NORCE) has installed and tested a suite of optical imaging sensors on the Lufttransport Dornier aircraft stationed in Longyearbyen as part of the SIOS-InfraNor project. Two optical sensors are installed onboard the Dornier aircraft (1) the PhaseOne IXU-180 RGB camera and (2) the HySpex VNIR-1800 hyperspectral sensor. The aircraft with these cameras is configured to acquire aerial RGB imagery and hyperspectral remote sensing data in addition to its regular transport operation in Svalbard. To date, SIOS has supported around 50 hours of flight time to acquire airborne data using Dornier aircraft in Svalbard for more than 20 scientific projects. Airborne imaging sensors include a variety of applications within glaciology, biology, hydrology, and other fields of Earth system science to understand the state of the environment of Svalbard. Mapping glacier crevasses, generating DEMs for glaciological applications, mapping and characterising earth (e.g., minerals, vegetation), ice (e.g., sea ice, icebergs, glaciers and snow cover) and ocean surface features (e.g. colour, chlorophyll) are examples of implementation. Aerial photos are also useful for monitoring the seasonal changes in snow, sea ice cover, and ocean colour. In 2021, SIOS conducted capacity building activities to train the next generation of polar scientists to use airborne imaging sensor data for their projects as part of the SIOS hyperspectral remote sensing training course (HSRS). This study presents a few selected applications from this course to demonstrate the potential of airborne imaging sensors in Svalbard. These include mapping water bodies (e.g. fjords, rivers), estimation of snow grain size, land cover classification, deriving chlorophyll, and mapping terrestrial vegetation. Preliminary results from these studies will be used to develop operational scientific applications and complement measurements from in-situ observations acquired by SIOS infrastructure in Svalbard. Eventually, these datasets will be valuable resources for calibration and validation activities for upcoming satellite hyperspectral missions, for example, the Copernicus Hyperspectral Imaging Mission for the Environment (CHIME).
- 15 February 2022
- Published by Optica Publishing Group in Optics Continuum
- Vol. 1 (2) , 427-441
Do-it-yourself VIS/NIR pushbroom hyperspectral imager with C-mount optics
This paper describes a new optomechanical design based on a previously presented do-it-yourself pushbroom hyperspectral imager (HSI) using commercial off-the-shelf (COTS) components. The new design uses larger aperture C-mount at F/2.8 instead of S-mount optics at F/4 to increase the throughput, which allows imaging at lower light levels. This is especially useful for dark surfaces like the deep ocean. The improved throughput is 6.77 higher at the center wavelength of 600 nm, which is shown both by theoretical calculations and experimental data. The measured full width at half maximum (FWHM) at 546.1 nm is 3.69 nm, which is close to the theoretical value of 3.3 nm, and smile and keystone are shown to be reduced in the new design. A method to characterize and remove second order effects using a cut-off filter is also presented and discussed.
- 15 February 2022
- Published by Optica Publishing Group in Optics Continuum
- Vol. 1 (2) , 427-441
Do-it-yourself VIS/NIR pushbroom hyperspectral imager with C-mount optics
This paper describes a new optomechanical design based on a previously presented do-it-yourself pushbroom hyperspectral imager (HSI) using commercial off-the-shelf (COTS) components. The new design uses larger aperture C-mount at F/2.8 instead of S-mount optics at F/4 to increase the throughput, which allows imaging at lower light levels. This is especially useful for dark surfaces like the deep ocean. The improved throughput is 6.77 higher at the center wavelength of 600 nm, which is shown both by theoretical calculations and experimental data. The measured full width at half maximum (FWHM) at 546.1 nm is 3.69 nm, which is close to the theoretical value of 3.3 nm, and smile and keystone are shown to be reduced in the new design. A method to characterize and remove second order effects using a cut-off filter is also presented and discussed.