RSRandall Scott Seright

Randall Scott Seright

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Randall Scott Seright has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Kinetics of Polymer Adsorption in Transport Through Porous Media: Basic Theory

    by Kenneth S. Sorbie, Randall S. Seright, Alan Beteta, Dongmei Wang, Celia Melo da Silva

    A polymer transport and kinetic adsorption model is developed and applied to assist in the understanding of some recent results in polymer flow through porous media. The coupled equations in dimensionless form show that the system is governed by 3 dimensionless numbers, 2 of which are important: the Adsorption number (NAd) and the adsorption Damköhler number (NDa-A). This leads to a wide range of behaviours in terms of the polymer effluent profiles, which are in broad qualitative agreement with experimental observations. The hypothesis is that it is the kinetics of the system (principally NDa-A) that is strongly controlling the experimental observations. The model also predicts that the way to establish if this is true is to conduct a polymer core flood including “shut-in” stages where flow is stopped, then resumed after some period of time, depending on the kinetic adsorption timescale. Preliminary experiments support this, and a following paper will present these experimental results directly simulated using our model.

  • Testing an Improved Method to Determine Inaccessible Pore Volume

    by R. S. Seright

    Summary: Inaccessible pore volume (IAPV) is intended to characterize the fraction of aqueous pore space in a porous medium that is not accessible to flowing polymer. Previous IAPV literature is contradictory in that no correlation is evident between measured IAPV values and rock permeability or porosity or polymer molecular weight (Mw) or size in solution. Prior work by Gilman and MacMillan (1987) and Wang et al. (2020) demonstrated that much of the previous contradictory reports may result from the inadequacies of methods to measure IAPV. In particular, the “double-polymer/tracer bank” method incorporates a water flush between two polymer/tracer banks. The unfavorable mobility ratio as water displaces the second polymer bank causes viscous fingering and overestimation of IAPV if insufficient water is flushed. [At least 100 pore volumes (PV) of water may be needed for an adequate flush, depending on the water/polymer mobility ratio.] Dean et al. (2022) proposed a potentially improved method to determine IAPV, where a low-concentration polymer bank is displaced by a more-concentrated, more-viscous polymer bank—so the mobility ratio is always favorable during the displacement. The aim of this study is to test this method for determining IAPV. The tests performed for this study used sandstone cores and bead packs with permeabilities ranging from 113 md to 18,600 md, porosities ranging from 0.188 to 0.402, and core lengths ranging from 30.48 cm to 122 cm. Many tests involved 500-ppm partially hydrolyzed polyacrylamide [HPAM; with no potassium iodide (KI) tracer] displacing 250-ppm HPAM (with a KI tracer). However, three sets of the tests made five replicate determinations of IAPV using successive polymer banks with HPAM concentrations starting at 62.5 ppm and doubling in stages to 2,000 ppm. This procedure tested the reproducibility of the method and whether the IAPV measurement depended on HPAM concentration. With a given data set, multiple methods can be used to assign an IAPV value, including (1) the area between the polymer and tracer breakout curves, (2) the difference in PV throughput (between polymer and tracer) upon attaining an effluent concentration of 50% of the injected concentration, and (3) the difference in PV during the first breakout of polymer ahead of tracer. Significant differences in calculated IAPV values were noted for these different methods. In general, the method of Dean et al. (2022) provides a substantial improvement over previous methods when measuring IAPV. However, caution must be exercised when interpreting the results of these tests with respect to projecting polymer-flood performance. Important uncertainties arise from assessments of IAPV—notably, in rock with permeability above 200 md. These uncertainties arise partly because polymer retention can vary with polymer concentration—violating a key assumption of the method of Dean et al. From this work, it is arguable whether a significant IAPV exists in Berea sandstone or bead packs with permeability greater than 200 md (when using 18–20-million g/mol HPAM).

  • Open Access

    The Kinetics of Polymer Adsorption in Transport Through Porous Media: Basic Theory

    by K. S. Sorbie, R. S. Seright, A. Beteta, D. Wang, C. da Silva

    A polymer transport and kinetic adsorption model is developed and applied to assist in the understanding of some recent results in polymer flow though porous media. The coupled equations in dimensionless form show that the system is governed by 3 dimensionless numbers, 2 of which are important, the Adsorption number (NAd) and the adsorption Damköhler number (NDa-A). This leads to a wide range of behaviours in terms of the polymer effluent profiles which are in broad qualitative agreement with experimental observations. The hypothesis is that it is the kinetics of the system (principally NDa-A) that is strongly controlling the experimental observations. The model also predicts that the way to establish if this is true, is to conduct polymer core flood including “shut-in” stages where flow is stopped, then resumed after some period of time, depending on the kinetic adsorption timescale. Preliminary experiments support this and a following paper will present these experimental results directly simulated using our model.

  • Does the Viscoelasticity of Low- and High-Salinity Polymers Desaturate the True Residual Oil from the Carbonates at Harsh Reservoir Conditions?

    by Dirie Dhahir, Madhar Sahib Azad, Subhash Ayirala, Randall S. Seright, Dhafer Al-Shehri, Mohammed Alotaibi

    Summary: Over the last two decades, high interest has been shown in exploring whether viscoelastic polymer solutions can reduce the capillary-trapped residual oil saturation (Sor) under practical sandstone reservoir conditions. Recently, efforts were dedicated to comparing the potential of biopolymer and synthetic polymers’ viscosity and viscoelasticity to reduce Sor at fluxes ranging from shear thinning to shear thickening from homogeneous and heterogeneous carbonate rocks (Dafaalla et al. 2025; Jain et al. 2026). Considering the prevailing lower fluxes of 0.02–0.05 ft/D (typically the Newtonian fluxes) in most of the polymer flood projects (Azad and Seright 2025) and the recently recognized importance of imposing bump waterflooding and glycerin flooding to arrive at true Sor (Ahmed et al. 2026), we explore pragmatically in this study the field-scale potential of low- and high-salinity viscoelastic polymer solutions to desaturate the true residual oil at harsh carbonate reservoir conditions. To do so, we measured capillary desaturation curves (CDCs) for viscoelastic polymer solutions, along with their ability to alter wettability. During this study, we conducted a combination of bulk and in-situ rheological measurements, contact angle experiments, and desaturation experiments. Desaturation experiments were performed using 2,500-ppm and 4,000-ppm acrylamide-ATBS-copolymer solutions prepared in 5,767-ppm total dissolved solids (TDS) and 57,670-ppm-TDS brines in 105–111-md oil-wet limestone cores saturated with 2.8-cp oil and 213,734-ppm-TDS formation brine at 95°C. The desaturation experiments involved (a) performing a bump waterflood up to 64 ft/D and a subsequent sequential glycerin flood to ensure that the residual oil was highly discontinuous and strongly trapped, and the core was well-swept; and (b) initiating the desaturation process with polymer solutions using an imposed flux of 0.05 ft/D and continuing up to 100 ft/D. Bump waterflooding and glycerin flooding reduced the oil saturation by 25–30% in both experiments. At low flux rates (from 0.05 ft/D to 1 ft/D), both low- and high-salinity polymer solutions did not reduce the oil saturation further. Such behavior is observed even though (a) the shear thickening onset was noted at 0.25 ft/D for both solutions, and (b) a slight reduction in contact angle (2–7°) was observed. At 5 ft/D, both low- and high-polymer solutions showed a noticeable reduction in Sor at computed critical capillary numbers of 4.0×10−5 and 4.82×10−5, respectively. Increasing the flux up to 100 ft/D resulted in significant desaturation, yielding additional residual oil recoveries of ~13% for the low-salinity polymer solution and ~11% for the high-salinity polymer solution. Although Sor reduction was observed at 5 ft/D in the laboratory, calculations indicate that achieving a flux above 5 ft/D in the target reservoir application and a significant Sor reduction would only be accomplished within ~30 ft from the wellbore. CDC curves for low- and high-salinity viscoelastic polymer solutions were reported for the first time under high-salinity and high-temperature oil-wet carbonate conditions. Examinations of the developed CDC curves indicate that the observed Sor reduction in the laboratory cannot be expected in the carbonate reservoirs for the typical well spacings used in polymer flood projects.

  • A Multiscale Evaluation of Polymer Injectivity and Fracture Behavior in the Wara Reservoir in the Burgan Field

    by Mohammad B. AlAbdullah, Meshal Algharaib, Randall S. Seright, Abbas Sanaseeri

    Summary: This paper provides a comprehensive analysis of polymer injectivity in the Wara reservoir in the Burgan field in Kuwait. Polymer flooding in the Wara reservoir is a strategic objective for the field plan to reach the Kuwait oil production target. The study presents and analyzes corefloods, rheological polymer measurements, fracture pressure field measurements, and long-term polymer field injectivity tests. All the data have been critically evaluated using analytical models to assess the polymer injectivity and potential fracture initiation and extension. Laboratory measurements of polymer bulk and in-situ viscosity were conducted using viscometers, while corefloods assessed the viscoelasticity of hydrolyzed polyacrylamide (HPAM) polymers under reservoir conditions [55°C, 162,000 ppm total dissolved solids (TDS)]. Step-rate tests in the field determined fracture initiation pressures, and long-term injectivity tests were performed at multiple rates. Field pressure responses were analyzed alongside coreflood results using the unified viscoelastic injectivity model (UVIM) coupled with a Perkins-Kern-Nordgren (PKN) fracture model. Geomechanical studies provided insights into fracture direction. This integrated approach ensured a thorough understanding of fracture initiation and polymer behavior. Initial predictions suggested that no fractures would occur during polymer injection. However, detailed analyses revealed that (assuming that severe mechanical degradation of the polymer did not occur) fractures were indeed present. This conclusion was drawn by comparing the polymer injectivity at various polymer concentrations with that of water injectivity. Polymer injectivity was found to be independent of polymer concentration, indicating potential in-situ fracture formation/extension due to polymer viscoelasticity. Laboratory coreflood experiments confirmed these findings, demonstrating that when the injection velocity exceeds 6–10 ft/day, the polymer’s extensional viscosity increases due to viscoelastic effects. As a result, the calculated pressure increases toward surpassing the fracture pressure of 2,500 psi (as measured in step-rate tests). The UVIM fracture model estimated a fracture extension of approximately 90 ft from the well. These findings are crucial for the effective planning of field-scale polymer flooding. The analysis indicates a need to clearly define the objective and design of polymer flooding within the high-permeability contrast Wara formation. This study provides critical insights into polymer injectivity and fracture management in the world’s largest sandstone oil field. It offers a novel, data-driven workflow for optimizing polymer flooding, addressing fracture risks from laboratory to field scale. The results suggest a correlation between rheo-thickening at elevated velocities and the onset of polymer-induced fracture behavior, offering a basis for improved understanding and potential optimization of polymer flooding practices.

  • Effect of Salinity and Hardness on Hydrolyzed Polyacrylamide Rheology in Sandstone

    by R. S. Seright, Stephane Jouenne, Carl Aften

    Summary: In this paper, we clarify the impact of salinity and hardness on partially hydrolyzed polyacrylamide (HPAM) rheology in sandstones with permeability greater than 200 md. For modelers/simulators of polymer flooding, the experimental findings should be of high relevance when projecting HPAM injectivity, fracture initiation, and whether viscoelasticity is significant in oil recovery of capillary-trapped residual oil with or without the presence of fractures. The literature review summarizes the effects of polymer concentration, molecular weight (Mw), rock permeability, and oil saturation on HPAM rheology in sandstones. The experimental work examines HPAM (18–20 million g/mol Mw, 30% degree of hydrolysis) rheology in sandstones with permeabilities ranging from 252 md to 838 md, salinities ranging from 0.1% to 10.5% total dissolved solids (TDS), and hardness levels ranging from 0% to 0.1% calcium chloride (CaCl2). As expected, the magnitude of resistance factors increased with increased HPAM concentration but decreased with increased salinity. The maximum resistance factor in the shear-thickening regime correlated well with C[µ]/(k/ϕ)0.5. The velocity dependence of the rheology (in sandstone) was largely unchanged by salinity between 0.1% and 5% TDS. At 1% TDS, the velocity dependence of rheology (in sandstone) was very weakly dependent on CaCl2 concentration between 0% and 0.1%. We examine the relationship between the onset of shear thickening and the inverse of the polymer solution relaxation time determined from bulk rheological data. The level of mechanical degradation was fairly unaffected by HPAM concentration between 25 ppm and 2,000 ppm [in brine with 1% sodium chloride (NaCl) and 0.05% CaCl2]. These findings should simplify the job of modelers when projecting the performance of polymer flooding.


  • Are Field Polymer Enhanced Oil Recovery Projects Reaping the Benefits of Residual Oil Saturation Reduction Due to Polymer Viscoelasticity?

    by Madhar Sahib Azad, Randall S. Seright

    Summary: For polymer solutions used in enhanced oil recovery (EOR), viscoelasticity is a rheological phenomenon that has a strong flux dependency and has been tied to significant reductions in residual oil saturation (Sor) during laboratory corefloods at high flux conditions. However, an unanswered question is whether the polymer’s viscoelastic effects reduce Sor over a significant portion of a polymer-flooded reservoir. In this paper, two methodologies are used to answer this question for polymer-flood projects across nine countries (Argentina, Austria, Canada, China, India, Oman, Russia, Suriname, and USA). In Method 1, the average Darcy velocity in each field is compared with the corresponding predicted velocity for the onset of shear thickening. Then, the effects of variables on Darcy velocity are examined, such as radial distance from the wellbore, well-spacing, horizontal well length, and thickness. In Method 2, the Sor reduction potential of the field polymer solutions used is evaluated by analyzing relevant coreflood experiments conducted in various laboratories. The observations from the laboratory results are considered in view of the fluid velocity, oil viscosity, permeability, mode of flooding, and pressure gradient of the various field projects. For most polymer floods with horizontal injectors, the highest possible Darcy velocity for various combinations of thickness, injection rate, horizontal well length, and well spacing is too low (in the range of ~0.01–0.2 ft/D) and unlikely to reach the onset velocity for viscoelastic behavior (i.e., >1 ft/D for most field conditions). For most vertical polymer injectors, less than 1% of the reservoir will experience fluid velocities high enough for viscoelasticity to potentially be important. Less-permeable reservoirs (<200 md) could experience the onset of shear thickening viscoelasticity at low rates (e.g., ~0.17 ft/D), but even so, a very small fraction of the reservoir is expected to achieve this onset flux. At a very short well spacing of 100 ft in the Pelican Lake polymer flood, the average velocity is ~1.7 ft/D. For an extreme case of a low thickness (10 ft), short horizontal well length (1,210 ft), and a small well spacing of 656 ft, an average velocity of ~1.2 ft/D and a pressure gradient of ~7.7 psi/ft were estimated for the Matzen field polymer flood. Although the average velocity is higher than the average onset flux rate, Sor reduction appears unlikely based on the macroscopic pressure gradients. This paper conveys the improbability of shear-thickening induced-viscoelasticity causing Sor reduction in field applications. It also discusses the potential role of other effects for Sor reduction in existing polymer floods, including wettability alteration by the polymer and secondary-vs.-tertiary polymer-flooding effects. EOR researchers are advised to use realistic field-relevant fluxes during laboratory assessments while studying Sor reduction.


  • Polymer Solution Preparation, Quality Control, and Produced Fluid Analysis at Milne Point

    by Almas Aitkulov, Connor Redwine, Jeremy Alvord, Reid Edwards, R. S. Seright

    Summary: This paper focuses on solution preparation and quality control activities associated with the Milne Point polymer flood on the North Slope of Alaska. This project uses 10 different polymer injection locations with a variety of skid types and configurations, which had a notable impact on polymer quality control and dissolution operations. Compared with bulk 500-kg to 750-kg polymer bags, silos greatly improved the storage capacity and increased the overall quality of the polymer solutions. Silos required less physical effort when transferring polymer. Polymer hydration skids that were made in-house by the polymer supplier were more reliable and experienced fewer polymer solution quality and startup issues than those that were outsourced. These in-house skids also used a uniform programming software that made it relatively easy to train the operators on new hydration skids. For pumping polymer mother solution, triplex pumps provided the best runtime and were most maintenance-friendly, compared with diaphragm or triple screw pumps. Because of the soluble iron present in the polymer makeup water, nitrogen blanketing was preferred to minimize corrosion and oxidative degradation. Inline static mixers were ineffective in mixing mother solution with dilution water when the mixing occurred close to the wellhead. Mixing the two streams too close to the wellhead led to substantial variations in wellhead viscosity measurements. Dedicating individual pumps for injection into a given well provided desirable flexibility in controlling rates and concentrations of polymer for the well. Monitoring produced salinity and polymer concentration provided useful insights about improved sweep and polymer retention associated with the polymer flood. The observed field behavior was consistent with laboratory studies, indicating a “tailing” phenomenon associated with polymer retention at Milne Point.


  • Open Access

    A Review of Polymer Gel Utilization in Carbon Dioxide Flow Control at the Core and Field Scale

    by Bergit Brattekås, Randall Seright

    Summary: Polymer gel has been used for water conformance control for several decades and may have significant potential in remediating unfavorable carbon dioxide (CO2) flow in the subsurface. High-mobility CO2 may channel quickly through sedimentary reservoirs, where unfavorable displacements are worsened in the presence of heterogeneities. Flow diversion technology targeting and withstanding CO2 is therefore essential to improving sweep efficiency and increasing storage potential. Polymer gel treatments have been demonstrated to remediate CO2 channeling in several enhanced oil recovery (EOR) field applications and have been proposed as a means to remediate wellbore and seal leakage during carbon sequestration. The goal of this review is to assess CO2 conformance control by polymer gel in published laboratory work related to both storage and EOR operations. Although field implementation of polymer gel has been successful in reducing CO2 flow, supporting experimental work on the laboratory scale is scattered, with both results and parameters varied. This paper summarizes the available literature and proposes a framework for future experimental work to aid more systematic assessment.


  • Literature Review and Experimental Observations of the Effects of Salinity, Hardness, Lithology, and ATBS Content on HPAM Polymer Retention for the Milne Point Polymer Flood

    by Randall S. Seright, Dongmei Wang

    Summary: At the Milne Point polymer flood (North Slope of Alaska), polymer retention is dominated by the clay, illite. Illite, and kaolinite cause no delay in polymer propagation in Milne Point core material, but they reduce the effective polymer concentration and viscosity by a significant amount (e.g., 30%), thus reducing the efficiency of oil displacement until the full injected polymer concentration is regained [which requires several pore volumes (PVs) of throughput]. This work demonstrates that polymer retention on illite is not sensitive to monovalent ion concentration, but it increases significantly with increased divalent cation concentration. The incorporation of a small percentage of acrylamido tertiary butyl sulfonic acid (ATBS) monomers into hydrolyzed polyacrylamide (HPAM) polymers is shown to dramatically reduce retention. The results are discussed in context with previous literature reports. Bridging adsorption was proposed as a viable mechanism to explain our results. Interestingly, an extensive literature review reveals that polymer retention (on sands and sandstones) is typically only modestly sensitive to the presence of oil. Extensive examination of the literature on inaccessible pore volume (IAPV) suggests the parameter was commonly substantially overestimated, especially in rock/sand more permeable than 500 md (which comprises the vast majority of existing field polymer floods).