KAKwaku Antwi

Kwaku Antwi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kwaku Antwi has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Anti-Termite Efficacy of Selected Leaf Extracts on Pycnanthus Angolensis Wood: A Comparative Study

    by Kwaku Antwi, Michael Darko Minta, Francis Kofi Bih, Mark Bright Donkoh, Salimatu Salifu Umar

    Wood is widely used in construction and manufacturing but is highly prone to biodeterioration, particularly in humid tropical regions. Conventional preservatives such as chromated copper arsenate (CCA) are effective but pose environmental and health risks, creating interest in more sustainable and less hazardous alternatives. This study assessed the preservative performance of leaf extracts from Azadirachta indica (neem), Chromolaena odorata (Siam weed), and Cedrela odorata (Spanish cedar) on Pycnanthus angolensis, a non-durable Ghanaian hardwood. Extracts were prepared with ethanol and water at 5%, 10%, and 20% w/v concentrations, and untreated samples served as controls. An in-ground field test was conducted, and termite resistance was evaluated by percentage weight loss. Untreated samples recorded the highest weight loss (93%), confirming the high susceptibility of the wood. All extract treatments reduced degradation to varying degrees. Neem performed best, with an average weight loss of 79%, followed by Chromolaena odorata (85%) and Cedrela odorata (88%). Ethanol extracts were more effective than water extracts, particularly at higher concentrations, with the most notable relative reductions observed at 20%. ANOVA confirmed significant effects of leaf type, solvent, and concentration. Although the treatments resulted in only partial protection and substantial biodeterioration remained, the findings demonstrate relative improvements compared to untreated wood. Neem leaf extracts, particularly ethanol-based treatments at 20%, showed the strongest comparative performance under the conditions tested. However, the results are based on a 90-day, short-term, single-site field trial and do not assess toxicity, leachability, or long-term environmental behavior.

  • Open Access

    Fibre-Vessel Structure, Density and Moisture Content Analysis of Zanthoxylum gilletii Wood with Comparative Evaluation Against Enthandrophragma cylindricum for Furniture Use

    by Delle Desire Domekyiir, Emmanuel Appiah-Kubi, Antwi Kwaku, Michael Awotwe-Mensah

    The density of wood is among several factors that influence the strength and durability of wood. However, scanty research is carried out on the effect of anatomical characteristics of wood. Fibre and vessels were sampled from three Ghanaian timbers, Zanthoxylum gilletii (Okuo) and Enthandrophragma cylindricum (Sapele) each. The study performed is to assess some key measurements; fibre length (FL), vessel diameter (VD), fibre diameter (FD), fibre lumen width (FLW), and fibre wall thickness (FWT) and density of wood of the selected tree. Results indicated highly significant (p<0.05) (Table 2) Specific variations revealed that Z. gilletii has the greatest fibre-vessel content and high density than E. cylindricum but was less moisture content to E. cylindricum. In terms of density, Z. gilletii ranged from 716 to 842 kg/m³, exceeding E. cylindricum range of 640 to 758 kg/m³ (Fig. 1). Fibre diameter for E. cylindricum ranged from 19.35 to 24.12 µm, whereas Z. gilletii showed slightly narrower fibres between 18.99 and 19.58 µm (Table 1). Overall, the denser, vessel-rich anatomy of Z. gilletii indicated a its high strength to buttress its potentials as a durable and efficient substitute for E. cylindricum and some well-known timber species (WKS) in furniture and structural applications. The higher density of Z. gilletii, combined with its lower moisture content, suggests enhanced resistance to fungal and insect damage and mechanical strength.

  • Open Access

    Investigating Physical and Mechanical Properties of Mahogany Root Wood (Khaya ivorensis) for its Utilization

    by Justine Wepia Apungu, Kwaku Antwi, Emmanuel Appiah-Kubi, Francis Kofi Bih, Joseph Zakaria

    The growing need for wood in construction and furniture production has led to a gradual increase for interest in other tree components, such as the use of root wood. However, to evaluate the quality of wood, one must consider its mechanical, anatomical, and physical characteristics. African mahogany (Khaya ivorensis) is a hard and durable wood that has been over-exploited. However, its other tree components, such as root wood, are available and considered waste left to rot. This study investigated the physical and mechanical properties of mahogany root wood and known properties of other wood species as an alternative base for wood resources. Root samples were extracted from three trees with three roots each, with average diameters of 54.3 cm, 23.3 cm, and 20.6 cm for trees 1, 2, and 3, respectively, and prepared according to BS 373 standard. All tests were investigated at the Kumasi CSRI (FORIG) laboratory. The results indicated that the root wood of the species dried at 17 - 20 % MC proved to be as good a material as its stem wood and branch wood counterparts in terms of physical and mechanical properties. Basic density values averaged 508 kg/m3, 531 kg/m3, and 569 kg/m3 across the roots. The green moisture content was 80 %, 76 % and 70 % for tree 1, 2, and 3, respectively. Average shrinkage was 0.84 %, 4.58 %, and 6.28 %, respectively, in longitudinal, tangential, and radial direction. MOE recorded 6724.4 MPa, 9276.0 MPa and 10010.0 MPa, MOR was 54.3 MPa, 76.1 MPa, and 78.5 MPa, compressive strength parallel to the grain was 41.8 MPa, 54.4 MPa, and 59.2 MPa, shear strength values ranged from 14.3 MPa, 15.4 MPa, to 17.2 and Janka hardness from 3.81 kN to 4.01 kN for tree 1, 2, and 3. Most of the recorded root wood results weresimilar to those of the stem and branch wood, indicating that it was equally fit for structural purposes.


  • Open Access

    VARIATION OF THE ANATOMIC CHARACTERISTICS OF Anthocleista grandiflora WOOD AS A FUNCTION OF TREE AGE AND TRUNK POSITION

    by Frank Kofi Dorwu, Kwaku Antwi, Prosper Mensah, Edgley Alves de Oliveira Paula, Fernando Rusch, Alexandre Santos Pimenta, Rafael Rodolfo de Melo

    This paper presents significant findings on the variation in the anatomical properties of Anthocleista grandiflora wood, which could greatly influence its utilization in various products. Cubic-shaped heartwood and sapwood specimens were extracted at the base, middle, and top of boles from 38-, 43-, and 47-year-old trees. The variations in cell morphology and anatomical characteristics were meticulously assessed. The specimens were prepared into 3 mm x 10 mm fragments, macerated, and viewed under a microscope using Motic Image plus 2.0 ML software. The following parameters were determined: average values of fiber length, fiber diameter, lumen width, double fiber wall thickness, Runkel ratio, aspect ratio, coefficient of rigidity, and coefficient of flexibility of trees at the base, middle, and top. Notably, there were more vessels in sapwood than in heartwood, and the vessel areas increased with increasing vessel lengths. The results also revealed that in the heartwood region, the fraction of vessel lumen increases with tree age in the base, middle, and top sections. These findings are significant as they provide a comprehensive understanding of the anatomical properties of A. grandiflora wood, which is classified as wood from numerous vessels, a common characteristic of noble woods. The wood exhibited anatomical properties suitable for cellulose, paper, and fiber-based products, highlighting its potential in various industries. Keywords: wood quality; fibers; morphological characterization; timber industry. Variação das características anatômicas da madeira de Anthocleista grandiflora em função da idade e da posição no troco RESUMO: Objetivou-se avaliar as propriedades anatômicas da madeira de Anthocleista grandiflora e as suas possíveis aplicações. Amostras do cerne e alburno foram extraídas na base, meio e topo de árvores com 38, 43 e 47 anos de idade. Em seguida, foram avaliadas variações na morfologia celular e nas características anatômicas, por meio de fragmentos de 3 mm x 10 mm, macerados e visualizados em microscópio utilizando o software Motic Image plus 2.0 ML. Foram avaliados: comprimento da fibra, diâmetro da fibra, largura do lúmen, espessura da parede dupla da fibra, razão de Runkel, razão de aspecto, coeficiente de rigidez e coeficiente de flexibilidade das árvores na base, meio e topo. Verificou-se mais vasos no alburno do que no cerne, e as áreas dos vasos aumentaram com o aumento de seu comprimento. Os resultados obtidos também indicaram que na região do cerne a fração do lúmen dos vasos aumenta com a idade árvores nas seções da base, intermediária e topo, sendo os valores de 14.76, 11.38 e 20.73 mm para 38 anos; 23.74, 22.13 e 23.09 mm para 43 anos; 28.62, 12.89 e 25.01 mm para 47 anos. A A. grandiflora foi classificada como madeira de numerosos vasos, característica comum para madeiras nobres. A madeira apresentou propriedades anatômicas adequadas para celulose, papel e produtos à base de fibras. Palavras-chave: qualidade da madeira; fibras; caracterização morfológica; indústria madeireira. This paper presents significant findings on the variation in the anatomical properties of Anthocleista grandiflora wood, which could greatly influence its utilization in various products. Cubic-shaped heartwood and sapwood specimens were extracted at the base, middle, and top of boles from 38-, 43-, and 47-year-old trees. The variations in cell morphology and anatomical characteristics were meticulously assessed. The specimens were prepared into 3 mm x 10 mm fragments, macerated, and viewed under a microscope using Motic Image plus 2.0 ML software. The following parameters were determined: average values of fiber length, fiber diameter, lumen width, double fiber wall thickness, Runkel ratio, aspect ratio, coefficient of rigidity, and coefficient of flexibility of trees at the base, middle, and top. Notably, there were more vessels in sapwood than in heartwood, and the vessel areas increased with increasing vessel lengths. The results also revealed that in the heartwood region, the fraction of vessel lumen increases with tree age in the base, middle, and top sections. These findings are significant as they provide a comprehensive understanding of the anatomical properties of A. grandiflora wood, which is classified as wood from numerous vessels, a common characteristic of noble woods. The wood exhibited anatomical properties suitable for cellulose, paper, and fiber-based products, highlighting its potential in various industries. Keywords: wood quality; fibers; morphological characterization; timber industry. Variação das características anatômicas da madeira de Anthocleista grandiflora em função da idade e da posição no troco RESUMO: Objetivou-se avaliar as propriedades anatômicas da madeira de Anthocleista grandiflora e as suas possíveis aplicações. Amostras do cerne e alburno foram extraídas na base, meio e topo de árvores com 38, 43 e 47 anos de idade. Em seguida, foram avaliadas variações na morfologia celular e nas características anatômicas, por meio de fragmentos de 3 mm x 10 mm, macerados e visualizados em microscópio utilizando o software Motic Image plus 2.0 ML. Foram avaliados: comprimento da fibra, diâmetro da fibra, largura do lúmen, espessura da parede dupla da fibra, razão de Runkel, razão de aspecto, coeficiente de rigidez e coeficiente de flexibilidade das árvores na base, meio e topo. Verificou-se mais vasos no alburno do que no cerne, e as áreas dos vasos aumentaram com o aumento de seu comprimento. Os resultados obtidos também indicaram que na região do cerne a fração do lúmen dos vasos aumenta com a idade...

  • Open Access

    Utilisation of Waste Shea Nutshell Fine-Grained Particles to Enhanced Strength and Durability Behaviour of Concrete

    by Patrick Zievie, Peter Paa-Kofi Yalley, Humphrey Danso, Kwaku Antwi

    Shea nutshells possess properties that stabilise soil enough to resist water penetration. It is a waste material and incorporating it as an additive material in concrete will be a means by which it can be recycled. With this projection, the study incorporated shea nutshell particles (SSP) as fine aggregates in concrete. The aim was to determine their influence on strength and durability properties. Fine aggregates were partially replaced with 0%, 10%, 20%, 30%, and 40% SSP based on the weight of the aggregate, and labelled as A0, S10, S20, S30 and S40 respectively. Concrete cubes of size 150 mm and cylinders of diameter 150 mm and height of 300 mm were prepared and cured for 7, 14, 28, and 90 days. The concrete was tested for density, compressive strength, split tensile strength, water absorption, and sulphate attack. The inclusion of the SSP did not improve the compressive and split tensile strengths. However, water absorption and sulphate attack decreased with further addition. Though, strength properties did not appreciate, values at 10%, 20% and 30% additions in 28 and 90 days satisfied the 28 days minimum requirement of 25 N/mm2. Hence, the study recommends the use of SSP in concrete production up to 30%.

  • Open Access

    NATURAL DURABILITY OF Acacia mangium WOOD

    by Thomas Tetteh Olaga, Kwaku Antwi, Francis Kofi Bih, Mark Bright Donkor

    Expanding the base of wood resources, adoption, and effective use of wood species depend primarily on the knowledge of the properties of the wood and the source from which the wood was obtained. The Acacia mangium wood, whose natural durability was determined to establish its practical uses, was extracted from Ada Technical Institute's compound in the Ada East District of the Greater Accra Region of Ghana. The study adopted an experimental research design. The natural durability test was done using the accelerated laboratory method based on standard. Seventy-two (72) samples were taken from the six billets (base, middle, and top). The analyses were carried out within each section, established from portions of the trees close to the pith or cascade. The resistance values indicated that the wood studied has a high resistance to rot. In this way, this wood can be used for various uses that require high resistance to interference, such as using parts in direct contact with the ground. Keywords: serviceable life; decay resistance; Xylophagous fungus. Durabilidade natural da madeira de Acacia mangium RESUMO: A expansão da base de recursos madeireiros, a adoção e o uso eficaz de espécies madeireiras dependem principalmente do conhecimento das propriedades da madeira e da fonte de onde a madeira foi obtida. As madeiras de Acacia mangium Willd, cuja durabilidade natural foi determinada para estabelecer seus usos práticos, foram avaliadas pelo Instituto Técnico Ada, no Distrito Leste de Ada, da Região da Grande Accra, em Gana. O estudo adotou um desenho de pesquisa experimental. O teste de durabilidade natural foi realizado utilizando o método laboratorial acelerado baseado em norma. Setenta e duas (72) amostras foram retiradas dos seis toras (base, meio e topo). As análises foram realizadas dentro de cadaa seção, sendo estabelecidos a partir de porções das árvores próximas à medula ou a casca. Os valores de resistência indicaram que a madeira estudada alta resistência ao apodrecimento. Desta forma, essa madeira pode ser utilizadas para diversos usos que exijam uma elevada resistência a deterioração, como o uso de peças em contato direto com solo. Palavras-chave: vida útil; resistência a deterioração; fungo xilófago.


  • Open Access

    Influence of age and trunk positions on physicomechanical properties of Anthocleista grandiflora Gilg wood

    by Frank Kofi Dorwu, Prosper Mensah, Kwaku Antwi, Rafael Rodolfo de Melo, Alexandre Santos Pimenta, Edgley Alves de Oliveira Paula, Fernando Rusch

    Population growth and the high demand for the use of wood already consolidated on the market have caused a high demand for forestry resources. This factor motivated the search for other species with properties that satisfy everyday needs in industrial applications. The research aims to characterize the physical-mechanical properties of Anthocleista grandiflora wood. Samples were taken to determine the properties of the three trunks’ base, middle, and top regions at 38, 43, and 47-year-old. Physical (density, moisture content, and volumetric increase) and mechanical tests (flexural strength, elasticity resistance, shear strength, and Janka hardness) were used to characterize the material. The results confirmed that the lowest average moisture content was presented at the base of 38-year-old trees, with values varying from 12.2 to 13.3% in the heartwood and sapwood regions. For density, the base of 47-year-old trees obtained the highest values, with a variation of 434.3–477.3 kg m–3 in the heartwood and sapwood regions. Mechanical flexural strength tests demonstrated that the highest value for the modulus of rupture was 63 MPa, indicated by samples taken from the heartwood of 43-year-old trees. The results show that A. Grandiflora wood can be used for various value-added purposes (construction, furniture, and other equipment).