Kaushik Das
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Kaushik Das has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Abhishek Bhattacharjee
Department of Electronics and Communication Engineering, National Institute of Technology, Agartala, Tripura, India
1 shared publication - Abhishek Nag
Department of ECE, National Institute of Technology, Agartala, Agartala, India
1 shared publication - Amit Das
Department of ECE, GLA University, Mathura, India
1 shared publication - Anjana Bhardwaj
GLA University
1 shared publication Debanjali Nath
Electronics and Communication Engineering Department National Institute of Technology Agartala India
1 shared publication- Preeti Goyal
Maharaja Agrasen Institute of Technology
1 shared publication
Latest Publications
- 11 August 2025
- Published by Springer Nature
- p. 39-55
Fundamentals of Photonics and Optoelectronics in Modern Industrial Processes
- 11 August 2025
- Published by Springer Nature
- p. 39-55
Fundamentals of Photonics and Optoelectronics in Modern Industrial Processes
- 1 February 2022
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 38 (1) , 91-105
Design of Power Gated SRAM Cell for Reducing the NBTI Effect and Leakage Power Dissipation During the Hold Operation
- 1 February 2022
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 38 (1) , 91-105
Design of Power Gated SRAM Cell for Reducing the NBTI Effect and Leakage Power Dissipation During the Hold Operation
- Open Access
- 20 July 2020
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 14 (6) , 741-749
FPGA and ASIC realisation of EMD algorithm for real‐time signal processing
In this study, the authors have proposed both field‐programmable gate array (FPGA) and application specific integrated circuit (ASIC) based realisation of the empirical mode decomposition (EMD) algorithm for the real‐time signal processing. Here, a single module is used for the calculation of maxima and minima, and another single module is used for the calculation of upper and lower envelopes instead of using separate modules for each calculation. In this work, the traditional cubic spline interpolation has been replaced with sawtooth transform followed by a smoothing module called moving average. In this study firstly, Verilog‐HDL code for the EMD is written using Xilinx Vivado and tested in the simulation phase, later dumped into Digilentinc Basys 3 FPGA board to do the hardware verification. For ASIC, the code is synthesised using Cadence Genus tool with the semi‐conductor laboratory 180 nm cell library and the layout is made in the Cadence Innovus tool. The proposed EMD can work with a clock/sampling rate up to 25 MHz and has a layout area of 3.9 mm 2 . For the reduction of power consumption of the overall system, clock gating has been used which helps to reduce the dynamic power of the modules, when they are not in use.
- 20 July 2020
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 14 (6) , 741-749
Open AccessFPGA and ASIC realisation of EMD algorithm for real‐time signal processing
In this study, the authors have proposed both field‐programmable gate array (FPGA) and application specific integrated circuit (ASIC) based realisation of the empirical mode decomposition (EMD) algorithm for the real‐time signal processing. Here, a single module is used for the calculation of maxima and minima, and another single module is used for the calculation of upper and lower envelopes instead of using separate modules for each calculation. In this work, the traditional cubic spline interpolation has been replaced with sawtooth transform followed by a smoothing module called moving average. In this study firstly, Verilog‐HDL code for the EMD is written using Xilinx Vivado and tested in the simulation phase, later dumped into Digilentinc Basys 3 FPGA board to do the hardware verification. For ASIC, the code is synthesised using Cadence Genus tool with the semi‐conductor laboratory 180 nm cell library and the layout is made in the Cadence Innovus tool. The proposed EMD can work with a clock/sampling rate up to 25 MHz and has a layout area of 3.9 mm 2 . For the reduction of power consumption of the overall system, clock gating has been used which helps to reduce the dynamic power of the modules, when they are not in use.