Ahmed S. Alsaman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmed S. Alsaman has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Ehab S. Ali
Interdisciplinary Research Center for Sustainable Energy Systems, KFUPM, Dhahran, Saudi Arabia
12 shared publications - Ahmed A. Askalany
Mechanical Department, Faculty of Technology and Education, Sohag University, Sohag, Egypt
7 shared publications - A. M. Farid
Mechanical Engineering Department, Tabbin Institute for Metallurgical Studies, Cairo, Egypt
6 shared publications Ehab S. Ali
Interdisciplinary Research Center for Sustainable Energy Systems, KFUPM, Dhahran, Saudi Arabia
6 shared publicationsRidha Ben Mansour
Interdisciplinary Research Center for Sustainable Energy Systems, KFUPM, Dhahran, Saudi Arabia
6 shared publications- Ridha Ben Mansour
Interdisciplinary Research Center for Sustainable Energy Systems (IRC-SES), King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
6 shared publications
Latest Publications
- Open Access
Review on Thermal Vacuum Desalination: Technologies, Challenges and Sustainable Pathways
Global water scarcity and the energy demand of conventional desalination motivate the development of thermal vacuum desalination (VD), which lowers the boiling temperature of saline water and can use low-grade heat from solar, waste-heat, ocean-thermal, and geothermal sources. This review traces the progression from passive natural-vacuum systems to forced-vacuum, ejector, spray-flash, falling-film, and membrane configurations. Reported headline values are case-specific. A reviewed multistage solar natural-vacuum configuration reported thermal efficiency up to 86%, and one experimental variable-geometry radial ejector reported an average entrainment-ratio improvement of 107% relative to its tested reference geometry. An experimental solar Venturi prototype produced 7.01–9.02 kg/(m2·d), depending on its operating cycle. Separately, a validated Aspen Plus simulation of a 14-effect MED-HV system reported a GOR of 13.49, while an experimental DCMD-crystallization study reported 98.9% water recovery for hypersaline produced water. Despite these promising results, the large-scale deployment of vacuum desalination technologies remains hindered by operational instabilities, intermittent thermal inputs, and membrane scaling. This review critically evaluates vacuum desalination technologies by distinguishing modeled, laboratory, pilot-scale, and review-derived evidence. It assesses energy consumption, techno-economic feasibility, and environmental performance on a case-specific basis. This review highlights major challenges in vacuum desalination (VD), such as vacuum stability, intermittent operation, scaling, irreversible membrane wetting, and long-term performance validation, and suggests research priorities for the future. Through this assessment of key findings, this review outlines a strategic approach to advancing thermal VD technologies toward sustainable, practical applications by integrating water treatment, energy efficiency, and mineral recovery through water–energy–mineral synergies.
Open AccessReview on Thermal Vacuum Desalination: Technologies, Challenges and Sustainable Pathways
Global water scarcity and the energy demand of conventional desalination motivate the development of thermal vacuum desalination (VD), which lowers the boiling temperature of saline water and can use low-grade heat from solar, waste-heat, ocean-thermal, and geothermal sources. This review traces the progression from passive natural-vacuum systems to forced-vacuum, ejector, spray-flash, falling-film, and membrane configurations. Reported headline values are case-specific. A reviewed multistage solar natural-vacuum configuration reported thermal efficiency up to 86%, and one experimental variable-geometry radial ejector reported an average entrainment-ratio improvement of 107% relative to its tested reference geometry. An experimental solar Venturi prototype produced 7.01–9.02 kg/(m2·d), depending on its operating cycle. Separately, a validated Aspen Plus simulation of a 14-effect MED-HV system reported a GOR of 13.49, while an experimental DCMD-crystallization study reported 98.9% water recovery for hypersaline produced water. Despite these promising results, the large-scale deployment of vacuum desalination technologies remains hindered by operational instabilities, intermittent thermal inputs, and membrane scaling. This review critically evaluates vacuum desalination technologies by distinguishing modeled, laboratory, pilot-scale, and review-derived evidence. It assesses energy consumption, techno-economic feasibility, and environmental performance on a case-specific basis. This review highlights major challenges in vacuum desalination (VD), such as vacuum stability, intermittent operation, scaling, irreversible membrane wetting, and long-term performance validation, and suggests research priorities for the future. Through this assessment of key findings, this review outlines a strategic approach to advancing thermal VD technologies toward sustainable, practical applications by integrating water treatment, energy efficiency, and mineral recovery through water–energy–mineral synergies.
- Open Access
- 10 August 2026
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 31
Experimental and environmental assessment of a photovoltaic/thermal-PEM electrolyzer system for hydrogen and low-grade heat cogeneration in a hot-arid climate
- 10 August 2026
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 31
Open AccessExperimental and environmental assessment of a photovoltaic/thermal-PEM electrolyzer system for hydrogen and low-grade heat cogeneration in a hot-arid climate
- Open Access
Techno-Economic and Environmental Assessment of Solar-Driven Hybrid Adsorption Desalination–HDH Using Silica Gel/Cacl2 Under Saudi Arabian Climate
This study explores a solar-driven hybrid desalination approach developed for Saudi Arabian climatic conditions, combining adsorption desalination (AD) based on a silica gel/CaCl2 composite with an ejector (EJ) and a HDH system. The proposed integration aims to enhance vapor utilization and reuse condenser heat to generate additional distillate. Two operating modes are examined, including a productivity-focused strategy that activates evaporator/condenser heat recovery (HR) when cooling is not required. Compared to raw silica gel (SG), the composite adsorbent improves adsorption cycle performance, raising the COP from about 0.38–0.43 to 0.55–0.63, and increasing SCP from roughly 130–240 W/kg to 320–675 W/kg. Without HR, the full AD–EJ–HDH system achieves SDWP of 52–100 m3/ton·day with GOR of 2.40–2.75 over the year. In HR-enabled operation, SDWP increases to 81–140 m3/ton·day and GOR rises to 2.7–2.95, reflecting stronger internal heat reuse and improved vapor management. Techno-economic results show that the solar-driven unit cost for AD–EJ–HDH decreases from winter values (2.7–2.9 $/m3) to a minimum around June (1.53 $/m3), while waste heat operation reduces the cost further to 0.49 $/m3 in June (rising to ~0.76–0.80 $/m3 in winter). With HR, the full AD–HR–EJ–HDH reaches around 1.44 $/m3 (solar, June) and 0.38–0.40 $/m3 (waste heat, summer), confirming the advantage of desalination-focused HR operation when cooling is not required. Finally, compared with SWRO, the AD–HR–EJ–HDH configuration delivers an approximately 90% lower carbon footprint on the same environmental assessment basis. The study highlights the environmental benefit of the intensified SG/CaCl2 hybrid configuration.
Open AccessTechno-Economic and Environmental Assessment of Solar-Driven Hybrid Adsorption Desalination–HDH Using Silica Gel/Cacl2 Under Saudi Arabian Climate
This study explores a solar-driven hybrid desalination approach developed for Saudi Arabian climatic conditions, combining adsorption desalination (AD) based on a silica gel/CaCl2 composite with an ejector (EJ) and a HDH system. The proposed integration aims to enhance vapor utilization and reuse condenser heat to generate additional distillate. Two operating modes are examined, including a productivity-focused strategy that activates evaporator/condenser heat recovery (HR) when cooling is not required. Compared to raw silica gel (SG), the composite adsorbent improves adsorption cycle performance, raising the COP from about 0.38–0.43 to 0.55–0.63, and increasing SCP from roughly 130–240 W/kg to 320–675 W/kg. Without HR, the full AD–EJ–HDH system achieves SDWP of 52–100 m3/ton·day with GOR of 2.40–2.75 over the year. In HR-enabled operation, SDWP increases to 81–140 m3/ton·day and GOR rises to 2.7–2.95, reflecting stronger internal heat reuse and improved vapor management. Techno-economic results show that the solar-driven unit cost for AD–EJ–HDH decreases from winter values (2.7–2.9 $/m3) to a minimum around June (1.53 $/m3), while waste heat operation reduces the cost further to 0.49 $/m3 in June (rising to ~0.76–0.80 $/m3 in winter). With HR, the full AD–HR–EJ–HDH reaches around 1.44 $/m3 (solar, June) and 0.38–0.40 $/m3 (waste heat, summer), confirming the advantage of desalination-focused HR operation when cooling is not required. Finally, compared with SWRO, the AD–HR–EJ–HDH configuration delivers an approximately 90% lower carbon footprint on the same environmental assessment basis. The study highlights the environmental benefit of the intensified SG/CaCl2 hybrid configuration.
- Open Access
High-Productivity Hybrid Adsorption Desalination Using a Sodium Polyacrylate/CaCl2 Composite with Dual Ejectors and Humidification–Dehumidification Under Saudi Arabian Climate Conditions
This study investigates the utilization of a sodium polyacrylate (SP)/CaCl2 composite as an adsorbent in a low-grade-heat desalination configuration designed for Saudi Arabian conditions. A dynamic system model was developed and validated for an adsorption desalination (AD) cycle integrated with a dual-ejector and a humidification–dehumidification (HDH) unit. Two operating modes were evaluated, including a production-oriented configuration that applies internal evaporator–condenser heat recovery (HR) when no cooling effect is required. Without HR, the AD–EJ–HDH system achieves 41–56 m3/ton·day SDWP and 2.6–2.9 GOR, with a freshwater cost of 1.8–2.4 $/m3 under solar driving and 0.70–0.90 $/m3 under waste heat. With HR, performance increases to SDWP 95–155 m3/ton·day and GOR 2.9–3.1, while costs decrease to about 1.34 $/m3 (solar) and 0.38 $/m3 (waste heat) in June. The SP/CaCl2 composite yields about 85% higher freshwater production than silica gel in the same system, highlighting the material’s potential for high-output hybrid adsorption desalination in hot-climate regions.
Open AccessHigh-Productivity Hybrid Adsorption Desalination Using a Sodium Polyacrylate/CaCl2 Composite with Dual Ejectors and Humidification–Dehumidification Under Saudi Arabian Climate Conditions
This study investigates the utilization of a sodium polyacrylate (SP)/CaCl2 composite as an adsorbent in a low-grade-heat desalination configuration designed for Saudi Arabian conditions. A dynamic system model was developed and validated for an adsorption desalination (AD) cycle integrated with a dual-ejector and a humidification–dehumidification (HDH) unit. Two operating modes were evaluated, including a production-oriented configuration that applies internal evaporator–condenser heat recovery (HR) when no cooling effect is required. Without HR, the AD–EJ–HDH system achieves 41–56 m3/ton·day SDWP and 2.6–2.9 GOR, with a freshwater cost of 1.8–2.4 $/m3 under solar driving and 0.70–0.90 $/m3 under waste heat. With HR, performance increases to SDWP 95–155 m3/ton·day and GOR 2.9–3.1, while costs decrease to about 1.34 $/m3 (solar) and 0.38 $/m3 (waste heat) in June. The SP/CaCl2 composite yields about 85% higher freshwater production than silica gel in the same system, highlighting the material’s potential for high-output hybrid adsorption desalination in hot-climate regions.
- 21 December 2025
- Published by Springer Nature in Adsorption
- Vol. 32 (1) , 7
A new combination of a solar-powered adsorption cooling system with a geothermal cooling source
- 21 December 2025
- Published by Springer Nature in Adsorption
- Vol. 32 (1) , 7
A new combination of a solar-powered adsorption cooling system with a geothermal cooling source
- Open Access
- 6 December 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 77
Performance evaluation and cost analysis of MOF-303-based adsorption desalination and cooling systems using experimental dynamic data
- 6 December 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 77
Open AccessPerformance evaluation and cost analysis of MOF-303-based adsorption desalination and cooling systems using experimental dynamic data
- 12 November 2025
- Published by Springer Nature in Adsorption
- Vol. 31 (8) , 1-25
Performance and economic analysis of solar-powered adsorption cooling desalination system with ejector integration utilizing composite adsorbent materials
- 12 November 2025
- Published by Springer Nature in Adsorption
- Vol. 31 (8) , 1-25
Performance and economic analysis of solar-powered adsorption cooling desalination system with ejector integration utilizing composite adsorbent materials
- Open Access
- 1 May 2025
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 126, 341-357
Cost analysis for solar-powered adsorption desalination-cooling system utilizing improved Maxsorb III adsorbents under Egypt weather conditions
- 1 May 2025
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 126, 341-357
Open AccessCost analysis for solar-powered adsorption desalination-cooling system utilizing improved Maxsorb III adsorbents under Egypt weather conditions