Lucinda Slattery
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lucinda Slattery has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Alan James Kennedy
Department of Pure and Applied Chemistry, University of Strathclyde, Glasgow, G1 1RX, UK
2 shared publications Alyssa Calomeni-Eck
US Army Engineer Research and Development Center, Environmental Laboratory, 3909 Halls Ferry Rd., Vicksburg, MS, 39180, United States
2 shared publicationsAnne Marie Coatney
Mississippi State University, Biomedical Engineering Student, 130 Creelman St., Mississippi State, MS, 39762, United States
2 shared publicationsCaroline C. Mastria
US Army Engineer Research and Development Center, Environmental Laboratory, 3909 Halls Ferry Rd., Vicksburg, MS, 39180, United States
2 shared publications- Roberto A. Lopez-Anido
Advanced Structures and Composites Center, University of Maine, Orono, ME 04469, USA
2 shared publications - Zackery McClelland
US Army Engineer Research and Development Center, Vicksburg, MS 39180, USA
2 shared publications
Latest Publications
- 3 November 2026
- Published by Elsevier in Composites Part B: Engineering
- Vol. 330
AI-enabled large-format additive manufacturing of thermoplastics: Recent advances and future directions
- 3 November 2026
- Published by Elsevier in Composites Part B: Engineering
- Vol. 330
AI-enabled large-format additive manufacturing of thermoplastics: Recent advances and future directions
- Open Access
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Embedded Fiber Optic Sensing for Structural Health Monitoring in Large Format Additive Manufacturing: An Integrated Approach
This research investigates the integration of fiber optic (FO) strain sensors into Large Format Additive Manufacturing (LFAM) components to enable real-time structural health monitoring (SHM) for civil infrastructure. The study addresses four fundamental questions: (1) Can embedded fiber optics reliably identify structural events and usage patterns? (2) Is adequate interfacial bonding achieved between the fiber optic sensor and polymer matrix? (3) How does the embedding process affect strain measurement accuracy? (4) What impact does sensor integration have on the mechanical performance of printed components? Twenty short carbon fiber-reinforced PLA specimens were fabricated in two configurations, neat and fiber-optic-embedded, and subjected to quasi-static tensile testing to failure and displacement-controlled cyclic fatigue testing. The embedding process leveraged LFAM’s layer-by-layer deposition and relatively low processing temperatures to place optical fibers between print layers without modifying standard print parameters. X-ray computed tomography revealed a fiber-to-matrix contact percentage of 58.2%, indicating that interfacial porosity introduced during embedding partially limits strain transfer and that absolute FO strain measurements should be interpreted alongside an independent reference measurement. Under cyclic fatigue loading, embedded FO sensors demonstrated strong qualitative agreement with load-cell-reported stress measurements, faithfully resolving cycle peaks, valleys, and transitions in real time. Quantitative differences between FO-measured strain and crosshead-derived applied strain were attributed to the limitations of crosshead displacement as a proxy for material strain, incomplete fiber-matrix contact, and local material heterogeneity. Across both testing regimes, the influence of FO embedment on bulk mechanical performance was inconsistent, with no systematic reduction in peak force or displacement, although inherent variability in the printed material limited definitive conclusions. These results demonstrate that fiber optic sensors can be embedded into LFAM components without meaningful disruption to fabrication or a consistent mechanical penalty, supporting the broader vision of self-sensing structural components with built-in monitoring capabilities. Further development is needed to improve fiber-matrix contact quality and expand the experimental test matrix for practical deployment in civil infrastructure applications.
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Open AccessEmbedded Fiber Optic Sensing for Structural Health Monitoring in Large Format Additive Manufacturing: An Integrated Approach
This research investigates the integration of fiber optic (FO) strain sensors into Large Format Additive Manufacturing (LFAM) components to enable real-time structural health monitoring (SHM) for civil infrastructure. The study addresses four fundamental questions: (1) Can embedded fiber optics reliably identify structural events and usage patterns? (2) Is adequate interfacial bonding achieved between the fiber optic sensor and polymer matrix? (3) How does the embedding process affect strain measurement accuracy? (4) What impact does sensor integration have on the mechanical performance of printed components? Twenty short carbon fiber-reinforced PLA specimens were fabricated in two configurations, neat and fiber-optic-embedded, and subjected to quasi-static tensile testing to failure and displacement-controlled cyclic fatigue testing. The embedding process leveraged LFAM’s layer-by-layer deposition and relatively low processing temperatures to place optical fibers between print layers without modifying standard print parameters. X-ray computed tomography revealed a fiber-to-matrix contact percentage of 58.2%, indicating that interfacial porosity introduced during embedding partially limits strain transfer and that absolute FO strain measurements should be interpreted alongside an independent reference measurement. Under cyclic fatigue loading, embedded FO sensors demonstrated strong qualitative agreement with load-cell-reported stress measurements, faithfully resolving cycle peaks, valleys, and transitions in real time. Quantitative differences between FO-measured strain and crosshead-derived applied strain were attributed to the limitations of crosshead displacement as a proxy for material strain, incomplete fiber-matrix contact, and local material heterogeneity. Across both testing regimes, the influence of FO embedment on bulk mechanical performance was inconsistent, with no systematic reduction in peak force or displacement, although inherent variability in the printed material limited definitive conclusions. These results demonstrate that fiber optic sensors can be embedded into LFAM components without meaningful disruption to fabrication or a consistent mechanical penalty, supporting the broader vision of self-sensing structural components with built-in monitoring capabilities. Further development is needed to improve fiber-matrix contact quality and expand the experimental test matrix for practical deployment in civil infrastructure applications.
- 10 June 2026
- Published by Elsevier in Journal of Environmental Management
- Vol. 411, 130185
Beneficial use of dredged sediment for removal of harmful algal bloom fueling nutrients
- 10 June 2026
- Published by Elsevier in Journal of Environmental Management
- Vol. 411, 130185
Beneficial use of dredged sediment for removal of harmful algal bloom fueling nutrients
- Open Access
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Beneficial Use of Dredged Sediment for Removal of Harmful Algal Bloom Fueling Nutrients
Harmful Algal Blooms (HABs) are a pervasive in freshwater and marine waters requiring advances in monitoring, prevention and control of active blooms. Prevention through interception of nutrient runoff that feed HABs is critical to reducing future impacts. This research provides a logical convergence of complementary goals of mitigating the severity of HABs and increasing beneficial use of dredged sediment conveniently sourced from Confined Disposal Facilities (CDFs). This work innovates use of additive manufacturing (AM), or 3D printing, to generate porous, geometrically complex sediment structures to adsorb and intercept nutrients in runoff water prior to discharge into surface water. While this technology application is widely applicable, proof-of-principle of nutrient removal capability is demonstrated using a 3D printed dredged sediment mound that was strategically placed on a 3 by 3-foot physical landscape model that was also completely 3D printed. The sediment mound structure was specifically printed into parallel roadways forming channels to increase preferential infiltration of run-off water into the otherwise clayey sediment. Nutrients were measured before and after pumped runoff water passed through either amended (biochar, commercial resins) or unamended dredged sediment structures and demonstrated that the unamended marine-sourced dredged sediment had sufficient capacity to almost immediately reduce concentrations of phosphate by 79 to 98% and nitrate by 93 to 99% from runoff discharge. This concept may be scaled using hoppers, excavators and trucks to move sediment from nearby CDFs to a runoff site for field demonstration and application.
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBeneficial Use of Dredged Sediment for Removal of Harmful Algal Bloom Fueling Nutrients
Harmful Algal Blooms (HABs) are a pervasive in freshwater and marine waters requiring advances in monitoring, prevention and control of active blooms. Prevention through interception of nutrient runoff that feed HABs is critical to reducing future impacts. This research provides a logical convergence of complementary goals of mitigating the severity of HABs and increasing beneficial use of dredged sediment conveniently sourced from Confined Disposal Facilities (CDFs). This work innovates use of additive manufacturing (AM), or 3D printing, to generate porous, geometrically complex sediment structures to adsorb and intercept nutrients in runoff water prior to discharge into surface water. While this technology application is widely applicable, proof-of-principle of nutrient removal capability is demonstrated using a 3D printed dredged sediment mound that was strategically placed on a 3 by 3-foot physical landscape model that was also completely 3D printed. The sediment mound structure was specifically printed into parallel roadways forming channels to increase preferential infiltration of run-off water into the otherwise clayey sediment. Nutrients were measured before and after pumped runoff water passed through either amended (biochar, commercial resins) or unamended dredged sediment structures and demonstrated that the unamended marine-sourced dredged sediment had sufficient capacity to almost immediately reduce concentrations of phosphate by 79 to 98% and nitrate by 93 to 99% from runoff discharge. This concept may be scaled using hoppers, excavators and trucks to move sediment from nearby CDFs to a runoff site for field demonstration and application.
- Open Access
Process–Structure–Property Relationship Development in Large-Format Additive Manufacturing: Fiber Alignment and Ultimate Tensile Strength
Parts made through additive manufacturing (AM) often exhibit mechanical anisotropy due to the time-based deposition of material and processing parameters. In polymer material extrusion (MEX), printed parts have weak points at layer interfaces, perpendicular to the direction of deposition. Poly(lactic acid) with chopped carbon fiber was printed on a large-format pellet printer at various extrusion rates with the same tool pathing to measure the fiber alignment with deposition via two methods and relate it to the ultimate tensile strength (UTS). Within a singular printed bead, an X-ray microscopy (XRM) scan was conducted to produce a reconstruction of the internal microstructure and 3D object data on the length and orientation of fibers. From the scan, discrete images were used in an image analysis technique to determine the fiber alignment to deposition without 3D object data on each fiber’s size. Both the object method and the discrete image method showed a negative relationship between the extrusion rate and fiber alignment, with −34.64% and −53.43% alignment per extrusion multiplier, respectively, as the slopes of the linear regression. Tensile testing was conducted to determine the correlation between the fiber alignment and UTS. For all extrusion rates tested, as the extrusion multiplier increased, the percent difference in the UTS decreased, to a minimum of 8.12 ± 14.40%. The use of image analysis for the determination of the fiber alignment provides a possible method for relating the microstructure to the meso-property of AM parts, and the relationship between the microstructure and the properties establishes process–structure–property relationships for large-format AM.
Open AccessProcess–Structure–Property Relationship Development in Large-Format Additive Manufacturing: Fiber Alignment and Ultimate Tensile Strength
Parts made through additive manufacturing (AM) often exhibit mechanical anisotropy due to the time-based deposition of material and processing parameters. In polymer material extrusion (MEX), printed parts have weak points at layer interfaces, perpendicular to the direction of deposition. Poly(lactic acid) with chopped carbon fiber was printed on a large-format pellet printer at various extrusion rates with the same tool pathing to measure the fiber alignment with deposition via two methods and relate it to the ultimate tensile strength (UTS). Within a singular printed bead, an X-ray microscopy (XRM) scan was conducted to produce a reconstruction of the internal microstructure and 3D object data on the length and orientation of fibers. From the scan, discrete images were used in an image analysis technique to determine the fiber alignment to deposition without 3D object data on each fiber’s size. Both the object method and the discrete image method showed a negative relationship between the extrusion rate and fiber alignment, with −34.64% and −53.43% alignment per extrusion multiplier, respectively, as the slopes of the linear regression. Tensile testing was conducted to determine the correlation between the fiber alignment and UTS. For all extrusion rates tested, as the extrusion multiplier increased, the percent difference in the UTS decreased, to a minimum of 8.12 ± 14.40%. The use of image analysis for the determination of the fiber alignment provides a possible method for relating the microstructure to the meso-property of AM parts, and the relationship between the microstructure and the properties establishes process–structure–property relationships for large-format AM.
- Open Access
In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall
This work focuses on simulating the thermal history of a vertical wall consisting of a thermoplastic composite material, poly(ethylene terephthalate) glycol (PETG) with short carbon fiber reinforcement, manufactured using a Big Area Additive Manufacturing (BAAM) system. The incremental deposition process used in additive manufacturing, which corresponds to the repeated deposition of hot material onto cooler material, contributes to the presence of residual stresses and part warping. The prediction of these mechanisms is dependent on thermal history of the part, and the major motivation of this work was to improve the accuracy of finite element (FE) models used to quantify the thermal history of large-format additively manufactured parts. Thermocouples were placed throughout the part at varying heights to measure temperature as a function of time. The FE model developed found a thermal contact conductance between the printed part and the bed of 10 W/m2K and convection coefficient values that linearly varied from 3 to 15 W/m2K through the wall height when making a temperature comparison with the output from the thermocouples. It is also demonstrated that the FE model with a constant convection coefficient under-predicts model temperature at the beginning of the manufacturing process when compared against the model with a variable convection coefficient. The impact of this difference was seen in the stress values, which were larger for the model with a constant convection coefficient. Finally, a correlation equation was derived which allows the findings to be generalized to other vertical structures manufactured on the BAAM. In summary, this work offers valuable insights on material characterization, real-time thermocouple placement, and FE modeling of large-format additively manufactured parts.
Open AccessIn Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall
This work focuses on simulating the thermal history of a vertical wall consisting of a thermoplastic composite material, poly(ethylene terephthalate) glycol (PETG) with short carbon fiber reinforcement, manufactured using a Big Area Additive Manufacturing (BAAM) system. The incremental deposition process used in additive manufacturing, which corresponds to the repeated deposition of hot material onto cooler material, contributes to the presence of residual stresses and part warping. The prediction of these mechanisms is dependent on thermal history of the part, and the major motivation of this work was to improve the accuracy of finite element (FE) models used to quantify the thermal history of large-format additively manufactured parts. Thermocouples were placed throughout the part at varying heights to measure temperature as a function of time. The FE model developed found a thermal contact conductance between the printed part and the bed of 10 W/m2K and convection coefficient values that linearly varied from 3 to 15 W/m2K through the wall height when making a temperature comparison with the output from the thermocouples. It is also demonstrated that the FE model with a constant convection coefficient under-predicts model temperature at the beginning of the manufacturing process when compared against the model with a variable convection coefficient. The impact of this difference was seen in the stress values, which were larger for the model with a constant convection coefficient. Finally, a correlation equation was derived which allows the findings to be generalized to other vertical structures manufactured on the BAAM. In summary, this work offers valuable insights on material characterization, real-time thermocouple placement, and FE modeling of large-format additively manufactured parts.
- Open Access
Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing
Large format polymer extrusion-based additive manufacturing has been studied recently due to its capacity for high throughput, customizable bead size and geometry, and ability to manufacture large parts. Samples from three fiber-filled amorphous thermoplastic materials 3D printed using a Masterprint 3X machine from Ingersoll Machine Tools were studied, along with their neat counterparts. Characterization techniques included thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and thermo-mechanical analysis (TMA). TGA results showed that the fillers decreased the degradation temperature for most of the materials investigated, with a 30 C decrease for polycarbonate (PC) and a 12 C decrease for polyethylene terephthalate glycol (PETG). For all the materials used, heat capacity increases with increasing temperature. Moreover, results show that a highly conductive filler increases the heat capacity. In contrast, a material with a lower conductivity decreases the heat capacity indicated in the 15.2% and 2.54% increase for acrylonitrile butadiene styrene (ABS) and PC and a 27.68% decrease for PETG. The TMA data show that the printed bead exhibits directional properties consistent with an orthotropic material. Smaller strains and coefficient of thermal expansion (CTE) were measured along the bead direction and across the bead compared to the through bead thickness showing that fillers are predominantly oriented in the bead direction, which is consistent with the literature. CTE values through bead thickness and neat material are similar in magnitude, which corresponds to the CTE of the matrix material. The experimental results serve to characterize the effect of fiber filler on the part thermal strains in three principal directions and two-part locations during the extrusion and bead deposition of large-format polymer extrusion-based additive manufacturing technologies.Open AccessEffects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing
Large format polymer extrusion-based additive manufacturing has been studied recently due to its capacity for high throughput, customizable bead size and geometry, and ability to manufacture large parts. Samples from three fiber-filled amorphous thermoplastic materials 3D printed using a Masterprint 3X machine from Ingersoll Machine Tools were studied, along with their neat counterparts. Characterization techniques included thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and thermo-mechanical analysis (TMA). TGA results showed that the fillers decreased the degradation temperature for most of the materials investigated, with a 30 C decrease for polycarbonate (PC) and a 12 C decrease for polyethylene terephthalate glycol (PETG). For all the materials used, heat capacity increases with increasing temperature. Moreover, results show that a highly conductive filler increases the heat capacity. In contrast, a material with a lower conductivity decreases the heat capacity indicated in the 15.2% and 2.54% increase for acrylonitrile butadiene styrene (ABS) and PC and a 27.68% decrease for PETG. The TMA data show that the printed bead exhibits directional properties consistent with an orthotropic material. Smaller strains and coefficient of thermal expansion (CTE) were measured along the bead direction and across the bead compared to the through bead thickness showing that fillers are predominantly oriented in the bead direction, which is consistent with the literature. CTE values through bead thickness and neat material are similar in magnitude, which corresponds to the CTE of the matrix material. The experimental results serve to characterize the effect of fiber filler on the part thermal strains in three principal directions and two-part locations during the extrusion and bead deposition of large-format polymer extrusion-based additive manufacturing technologies.