Masayoshi Inoue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Masayoshi Inoue has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Ryo Teranishi
Kyushu University
5 shared publications - Takanobu Kiss
Kyushu University
3 shared publications - Akiyoshi Matsumoto
National Institute for Materials Science
2 shared publications - Kohei Higashikawa
Department of Electrical Engineering, Graduate School of Information Science and Electrical Engineering, Kyushu University, Fukuoka, Japan
2 shared publications - Masataka Iwakuma
Kyushu University, Fukuoka, Japan
2 shared publications - Masato Tsuro
Faculty of Agriculture, Meijo University
2 shared publications
Latest Publications
- Open Access
- 20 November 2024
- Published by Cryogenic Association of Japan in Teion Kogaku (Journal of Cryogenics and Superconductivity Society of Japan)
- Vol. 59 (6) , 330-331
Inoue Laboratory, Department of Electrical Engineering, Faculty of Engineering, Fukuoka Institute of Technology
- 20 November 2024
- Published by Cryogenic Association of Japan in Teion Kogaku (Journal of Cryogenics and Superconductivity Society of Japan)
- Vol. 59 (6) , 330-331
Open AccessInoue Laboratory, Department of Electrical Engineering, Faculty of Engineering, Fukuoka Institute of Technology
- 13 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Observation of Crack Formation Caused by Twisting in REBCO Coated Conductors by Using Scanning Hall-Probe Microscopy
In magnet applications using REBa 2 Cu 3 O y (RE = rare earth, Y, Gd, etc., REBCO) coated conductors, micro-cracks caused by mechanical slitting are one of the most worrisome phenomena because they could be the origin of critical current degradation. In this study, we have investigated the crack formation caused by twisting the REBCO tape by using scanning Hall-probe microscopy (SHPM) and scanning electron microscope (SEM). First, twist, the most severe load on the crack, was applied to the 4 mm-wide REBCO tape divided by mechanical slitting, and the variation of critical current with the torsion angles was investigated. Then, magnetization distribution measured by SHPM revealed that these decreases in critical current correspond to crack formation. The micro-cracks introduced initially during the slitting process are not the origin of the crack formation that spread throughout the tape. On the other hand, for the REBCO tape after the irreversible twist test, additional cracks have also been confirmed even though the critical current has not yet decreased.
- 13 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Observation of Crack Formation Caused by Twisting in REBCO Coated Conductors by Using Scanning Hall-Probe Microscopy
In magnet applications using REBa 2 Cu 3 O y (RE = rare earth, Y, Gd, etc., REBCO) coated conductors, micro-cracks caused by mechanical slitting are one of the most worrisome phenomena because they could be the origin of critical current degradation. In this study, we have investigated the crack formation caused by twisting the REBCO tape by using scanning Hall-probe microscopy (SHPM) and scanning electron microscope (SEM). First, twist, the most severe load on the crack, was applied to the 4 mm-wide REBCO tape divided by mechanical slitting, and the variation of critical current with the torsion angles was investigated. Then, magnetization distribution measured by SHPM revealed that these decreases in critical current correspond to crack formation. The micro-cracks introduced initially during the slitting process are not the origin of the crack formation that spread throughout the tape. On the other hand, for the REBCO tape after the irreversible twist test, additional cracks have also been confirmed even though the critical current has not yet decreased.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Consideration of Magnetic Flux Distribution in Multi−Filamented YBa2Cu3O7−δ Films by Controlling Crystal Array Using Surface−Modified Substrate
Large direct currents can flow through REBa 2 Cu 3 O 7−δ (REBCO) wires without energy loss because of zero resistance. However, they suffer from alternating current (AC) loss. To reduce AC loss, multifilamentation is effective. Motivation of this study is to expand the possibilities of multifilament technology in two points of view. One is to adapt chemical method for film deposition, other is to narrow distance between filaments. In this study, a multifilament of YBa 2 Cu 3 O 7−δ (YBCO) was fabricated using a metal−organic deposition (MOD) method on the substrates modified by a photolithography technique. As a result, a multifilament YBCO film was successfully fabricated using MOD method. Also, narrow distance between filaments in 5 μm was succeeded. These results contribute to expand process options of multifilament fabrication.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Consideration of Magnetic Flux Distribution in Multi−Filamented YBa2Cu3O7−δ Films by Controlling Crystal Array Using Surface−Modified Substrate
Large direct currents can flow through REBa 2 Cu 3 O 7−δ (REBCO) wires without energy loss because of zero resistance. However, they suffer from alternating current (AC) loss. To reduce AC loss, multifilamentation is effective. Motivation of this study is to expand the possibilities of multifilament technology in two points of view. One is to adapt chemical method for film deposition, other is to narrow distance between filaments. In this study, a multifilament of YBa 2 Cu 3 O 7−δ (YBCO) was fabricated using a metal−organic deposition (MOD) method on the substrates modified by a photolithography technique. As a result, a multifilament YBCO film was successfully fabricated using MOD method. Also, narrow distance between filaments in 5 μm was succeeded. These results contribute to expand process options of multifilament fabrication.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Microstructural Study of YBCO Thin Films With Stripe-Patterned Substrates for Ultra-Fine Multi-Filaments
Rare-earth barium copper oxide (REBCO) superconductors can be applied to superconducting magnets in low-temperature and high-magnetic-field and electric power equipment. Currently available superconducting wires supplied by many companies are tape-shaped, and a thin REBCO film is formed by depositing multiple buffer layers on a thin metal substrate. Coated conductors fabricated on such a flat substrate have a structure close to a single crystal and have high critical current density properties. In contrast, reducing the screening current is an important issue for practical applications such as high-field superconducting coils. In this study, we proposed a patterned multifilamentary thin film with a stripe pattern, fabricated on a substrate via photolithography. YBa 2 Cu 3 O x was deposited onto stripe with Nb metal. Any stripe material can be used to separate superconducting and non-superconducting wires based on magneto-optical observations. Based on TEM/STEM-EDX observations, impurity phases such as NbBaO were formed on the STO/Nb strip. These results suggested that the use of a substrate with a stripe pattern is useful for fabricating multifilamentary coated conductors.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Microstructural Study of YBCO Thin Films With Stripe-Patterned Substrates for Ultra-Fine Multi-Filaments
Rare-earth barium copper oxide (REBCO) superconductors can be applied to superconducting magnets in low-temperature and high-magnetic-field and electric power equipment. Currently available superconducting wires supplied by many companies are tape-shaped, and a thin REBCO film is formed by depositing multiple buffer layers on a thin metal substrate. Coated conductors fabricated on such a flat substrate have a structure close to a single crystal and have high critical current density properties. In contrast, reducing the screening current is an important issue for practical applications such as high-field superconducting coils. In this study, we proposed a patterned multifilamentary thin film with a stripe pattern, fabricated on a substrate via photolithography. YBa 2 Cu 3 O x was deposited onto stripe with Nb metal. Any stripe material can be used to separate superconducting and non-superconducting wires based on magneto-optical observations. Based on TEM/STEM-EDX observations, impurity phases such as NbBaO were formed on the STO/Nb strip. These results suggested that the use of a substrate with a stripe pattern is useful for fabricating multifilamentary coated conductors.
- 27 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Current Transport Characteristics for REBCO Tape in High Electric Field
The current-electric field ( I-E ) characteristic including high electric fields is a key parameter in the detailed design of power devices such as superconducting rotating machines and superconducting current limiters using REBa 2 Cu 3 O y (REBCO, where RE is a rare element) tapes. However, because the REBCO tape may burn out due to heat generation in standard current-carrying measurements, the measurements have been carried out only up to the electric field range of 1 µV/cm, which is the electric field criterion. In this study, the I-E characteristics of REBCO tapes, including high electric fields, were measured using the pulsed current method. Using two different measurement systems with the pulse width ( τ p ) of 10 msec and 2 sec, we have successfully obtained the I-E characteristics of REBCO tape over a wide range of five orders of magnitude than the electric field criterion (1 μV/cm to 100 mV/cm). Furthermore, the I-E property of a composite conductor consisting of REBCO tape and a thick copper plate was estimated by combining the experimental results of the I-E property with that of copper and compared with the experimental results. The results showed good agreement between both. The measurement of I-E characteristics over a wide range of the electric field, including high electric fields, would be useful for predicting the characteristics of composite conductors, evaluating their performance, and designing devices.
- 27 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Current Transport Characteristics for REBCO Tape in High Electric Field
The current-electric field ( I-E ) characteristic including high electric fields is a key parameter in the detailed design of power devices such as superconducting rotating machines and superconducting current limiters using REBa 2 Cu 3 O y (REBCO, where RE is a rare element) tapes. However, because the REBCO tape may burn out due to heat generation in standard current-carrying measurements, the measurements have been carried out only up to the electric field range of 1 µV/cm, which is the electric field criterion. In this study, the I-E characteristics of REBCO tapes, including high electric fields, were measured using the pulsed current method. Using two different measurement systems with the pulse width ( τ p ) of 10 msec and 2 sec, we have successfully obtained the I-E characteristics of REBCO tape over a wide range of five orders of magnitude than the electric field criterion (1 μV/cm to 100 mV/cm). Furthermore, the I-E property of a composite conductor consisting of REBCO tape and a thick copper plate was estimated by combining the experimental results of the I-E property with that of copper and compared with the experimental results. The results showed good agreement between both. The measurement of I-E characteristics over a wide range of the electric field, including high electric fields, would be useful for predicting the characteristics of composite conductors, evaluating their performance, and designing devices.
- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
The Effect of Mechanical Slitting on 1 mm-Width REBCO Coated Conductors
In recent years, to reduce AC loss and ensure flexibility, narrow REBa 2 Cu 3 O y (REBCO, RE = Gd, Y, Sm, etc.) coated conductors (CCs) have been developed. A standard method common of CC narrowing is mechanical slitting with a slitting blad. However, cracks may occur near the slit edge due to the impact during slitting, which may affect the critical current density ( J c ). In particular, for 1 and 2 mm-width CCs, the effect of this damage becomes more significant than that for 4 mm-width CCs. In this study, we have investigated the effect of mechanical slitting on 1 mm-width REBCO CC by J c distribution measurement, microstructural observation, and in-field J c measurement. Also, comparisons with 2 and 4 mm-width CCs fabricated by a similar process were conducted. From the J c distribution analysis, J c along the slit edges for 1 mm-width CC fluctuated more than those for 2 and 4 mm-width CCs. Microcracks and delamination were observed at the slit edges of the 1 to 4 mm-width CCs. These were longitudinally continuous and may occur during slitting. The density or relative portion of cracked area induced in the REBCO layer by slitting was increased as the width of the CC narrowed. Furthermore, it is confirmed that large microcracks of up to about 200 μm corresponded to the region of fluctuating J c . In-field J c , 1 mm-width CC had a lower J c than 2 and 4 mm-width CCs. These results indicate that microcrack propagation increases with narrower CCs and has a more pronounced effect on the critical current. Microcracks and delamination are predicted to be more significant when the CC is slit into narrow CCs, such as 0.5 mm-width.
- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
The Effect of Mechanical Slitting on 1 mm-Width REBCO Coated Conductors
In recent years, to reduce AC loss and ensure flexibility, narrow REBa 2 Cu 3 O y (REBCO, RE = Gd, Y, Sm, etc.) coated conductors (CCs) have been developed. A standard method common of CC narrowing is mechanical slitting with a slitting blad. However, cracks may occur near the slit edge due to the impact during slitting, which may affect the critical current density ( J c ). In particular, for 1 and 2 mm-width CCs, the effect of this damage becomes more significant than that for 4 mm-width CCs. In this study, we have investigated the effect of mechanical slitting on 1 mm-width REBCO CC by J c distribution measurement, microstructural observation, and in-field J c measurement. Also, comparisons with 2 and 4 mm-width CCs fabricated by a similar process were conducted. From the J c distribution analysis, J c along the slit edges for 1 mm-width CC fluctuated more than those for 2 and 4 mm-width CCs. Microcracks and delamination were observed at the slit edges of the 1 to 4 mm-width CCs. These were longitudinally continuous and may occur during slitting. The density or relative portion of cracked area induced in the REBCO layer by slitting was increased as the width of the CC narrowed. Furthermore, it is confirmed that large microcracks of up to about 200 μm corresponded to the region of fluctuating J c . In-field J c , 1 mm-width CC had a lower J c than 2 and 4 mm-width CCs. These results indicate that microcrack propagation increases with narrower CCs and has a more pronounced effect on the critical current. Microcracks and delamination are predicted to be more significant when the CC is slit into narrow CCs, such as 0.5 mm-width.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Filament Structure Analysis of Multifilament MgB2 Wires by Using X-ray CT
We have investigated the filament structure of 18-filament MgB 2 wires by using an X-ray computed tomography (CT). For the structural analysis of MgB 2 filaments and Nb barriers, we adopted two image processing, the adoptive binarization method and the closing technique, to the series of cross-sectional CT images. After the image processing, we successfully eliminated the effect of several artifacts, such as metal artifacts and beam hardening, and extrapolated the area of MgB 2 filaments and Nb barriers. From the images, we made a three-dimensional model of MgB 2 filaments and confirmed whether the breakout of the filaments and sausaging phenomena exist or not. Although the broken filaments were not observed, the Nb barrier's break was confirmed in all six inner filaments of the MgB 2 wire after heat treatment. Moreover, from the statistical distribution analysis, sausaging is more significant in the inner filament than in the outer filament. These results indicate that the X-ray CT observation and advanced image processing is effective in understanding the filament structure in non-destructive ways.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Filament Structure Analysis of Multifilament MgB2 Wires by Using X-ray CT
We have investigated the filament structure of 18-filament MgB 2 wires by using an X-ray computed tomography (CT). For the structural analysis of MgB 2 filaments and Nb barriers, we adopted two image processing, the adoptive binarization method and the closing technique, to the series of cross-sectional CT images. After the image processing, we successfully eliminated the effect of several artifacts, such as metal artifacts and beam hardening, and extrapolated the area of MgB 2 filaments and Nb barriers. From the images, we made a three-dimensional model of MgB 2 filaments and confirmed whether the breakout of the filaments and sausaging phenomena exist or not. Although the broken filaments were not observed, the Nb barrier's break was confirmed in all six inner filaments of the MgB 2 wire after heat treatment. Moreover, from the statistical distribution analysis, sausaging is more significant in the inner filament than in the outer filament. These results indicate that the X-ray CT observation and advanced image processing is effective in understanding the filament structure in non-destructive ways.
- 16 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Fabrication of a Magnetic Field Shielding Resin Sheet Using YBa2Cu3O7-δ Powders
YBa 2 Cu 3 O 7-δ (YBCO) superconductors exhibit the perfect diamagnetism effect at a critical temperature (T c ) of 93 K or lower. This effect can be exploited by creating materials that shield the magnetic field. In this study, light and flexible magnetic field shielding sheets were prepared by mixing a polyethylene terephthalate (PET) resin with YBCO powders of different particle sizes. The investigation of the effect of the YBCO particle size on the structure of the sheets formed resulted in the preparation of sheets in which YBCO powders were uniformly dispersed in the resin. By contrast, sheets that were prepared with using larger particle sizes showed more cracks and vacancies. The ease of occurrence of cracks and pores was determined to be dependent on the particle size, and it was shown that powders with small particle sizes are suitable for sheets.
- 16 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-4
Fabrication of a Magnetic Field Shielding Resin Sheet Using YBa2Cu3O7-δ Powders
YBa 2 Cu 3 O 7-δ (YBCO) superconductors exhibit the perfect diamagnetism effect at a critical temperature (T c ) of 93 K or lower. This effect can be exploited by creating materials that shield the magnetic field. In this study, light and flexible magnetic field shielding sheets were prepared by mixing a polyethylene terephthalate (PET) resin with YBCO powders of different particle sizes. The investigation of the effect of the YBCO particle size on the structure of the sheets formed resulted in the preparation of sheets in which YBCO powders were uniformly dispersed in the resin. By contrast, sheets that were prepared with using larger particle sizes showed more cracks and vacancies. The ease of occurrence of cracks and pores was determined to be dependent on the particle size, and it was shown that powders with small particle sizes are suitable for sheets.
- 7 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-4
J c and Composition Distribution of YBCO Coated Conductors Fabricated by the TFA-MOD Process
The Trifluoroacetate-Metal Organic Deposition (TFA-MOD) process is one of the most promising fabrication processes for low-cost superconducting coated conductors (CCs) because of its high yield and non-vacuum system. However, in the doping and multi-coating process for the enhancement of critical current ( I c ), degradation of I c often occurs. In this study, to clarify the origin of I c degradation, we have investigated the local critical current density ( J c ) distribution, in-field J c properties and the variation of composition for TFA-MOD processed YBa 2 Cu 3 O y (YBCO) CCs. The local J c distributions were measured by Scanning Hall-Probe Microscopy for confirming the location of the high/low- J c regions. The CCs were then cut into 3 mm×3 mm or 3 mm×4 mm for dc magnetization measurement. The T c of the all samples were about 87 K to 90 K. In-field J c at 77 K was obtained from M - H measurements and all the samples were compared with each other. The in-field J c of high- J c sample showed about 100 times higher value than that of the low- J c sample. Then we have observed the microchemistry and the variation of composition by SEM-EDS. In the high- J c sample, the grains of the superconducting phase were large in size and were connected to each other. This means that superconducting current could form through the whole sample area and generate a large magnetic moment. On the other hand, in the low- J c sample, though the superconducting phase could be observed, the grains were small in size and sparse. Therefore, the magnetic moment measured was small. However, it was also suggested that the intra-grain J c would be almost the same as that of high- J c sample.
- 7 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-4
J c and Composition Distribution of YBCO Coated Conductors Fabricated by the TFA-MOD Process
The Trifluoroacetate-Metal Organic Deposition (TFA-MOD) process is one of the most promising fabrication processes for low-cost superconducting coated conductors (CCs) because of its high yield and non-vacuum system. However, in the doping and multi-coating process for the enhancement of critical current ( I c ), degradation of I c often occurs. In this study, to clarify the origin of I c degradation, we have investigated the local critical current density ( J c ) distribution, in-field J c properties and the variation of composition for TFA-MOD processed YBa 2 Cu 3 O y (YBCO) CCs. The local J c distributions were measured by Scanning Hall-Probe Microscopy for confirming the location of the high/low- J c regions. The CCs were then cut into 3 mm×3 mm or 3 mm×4 mm for dc magnetization measurement. The T c of the all samples were about 87 K to 90 K. In-field J c at 77 K was obtained from M - H measurements and all the samples were compared with each other. The in-field J c of high- J c sample showed about 100 times higher value than that of the low- J c sample. Then we have observed the microchemistry and the variation of composition by SEM-EDS. In the high- J c sample, the grains of the superconducting phase were large in size and were connected to each other. This means that superconducting current could form through the whole sample area and generate a large magnetic moment. On the other hand, in the low- J c sample, though the superconducting phase could be observed, the grains were small in size and sparse. Therefore, the magnetic moment measured was small. However, it was also suggested that the intra-grain J c would be almost the same as that of high- J c sample.
- 18 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Current Capacity of Cu-Sheathed Multifilamentary Coated Conductors Under the Influence of Spatial Variation of Local Critical Currents in Each Filament
We investigated the relationship between current capacity and local critical current distribution of a Cu-sheathed multi-filamentary RE-123 coated conductor (CC). Patterning multi-filamentary structure on CCs will be a promising solution for reducing magnetization to assure spatial homogeneity and its temporal stability of magnet applications such as MRI and NMR. On the other hand, it will become more difficult to maintain the current capacity because a smaller defect can block the current flow in a narrower filament. Permitting electrical coupling among the filaments will work for maintaining current capacity because current can avoid such a defect by flowing into the adjacent filament. However, too small inter-filamentary resistance will result in long time constant of filament coupling which will affect spatial homogeneity and its temporal stability of magnet applications. Therefore, to design a multi-filamentary CC satisfying the requirement from magnet applications, it is necessary to understand the quantitative impact of inter-filamentary resistance of the multi-filamentary CC on its current capacity under the influence of spatial variation of local critical currents. In this study, we estimated global critical current of a Cu-sheathed multi-filamentary CC as a function of inter-filamentary resistance by considering its local critical current distribution in each filament.
- 18 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Current Capacity of Cu-Sheathed Multifilamentary Coated Conductors Under the Influence of Spatial Variation of Local Critical Currents in Each Filament
We investigated the relationship between current capacity and local critical current distribution of a Cu-sheathed multi-filamentary RE-123 coated conductor (CC). Patterning multi-filamentary structure on CCs will be a promising solution for reducing magnetization to assure spatial homogeneity and its temporal stability of magnet applications such as MRI and NMR. On the other hand, it will become more difficult to maintain the current capacity because a smaller defect can block the current flow in a narrower filament. Permitting electrical coupling among the filaments will work for maintaining current capacity because current can avoid such a defect by flowing into the adjacent filament. However, too small inter-filamentary resistance will result in long time constant of filament coupling which will affect spatial homogeneity and its temporal stability of magnet applications. Therefore, to design a multi-filamentary CC satisfying the requirement from magnet applications, it is necessary to understand the quantitative impact of inter-filamentary resistance of the multi-filamentary CC on its current capacity under the influence of spatial variation of local critical currents. In this study, we estimated global critical current of a Cu-sheathed multi-filamentary CC as a function of inter-filamentary resistance by considering its local critical current distribution in each filament.