HKHiroharu Kamada

Hiroharu Kamada

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hiroharu Kamada has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Operation Scenario of Mobile SMES for On-Site Eigenvalue Measurement of Electric Power System

    by Shinichi Nomura, Hiroharu Kamada, Hang Xu, Tanzo Nitta, Takakazu Shintomi, Naoki Hirano, Yushi Miura

    Eigenvalues are essential values for discussing the stable operation of the power system. However, the eigenvalues vary in real-time, and their distribution is complex in the power system. The authors conduct a design study on a 1 MJ-class mobile superconducting magnetic energy storage (SMES), enabling the eigenvalue measurement while changing locations. To achieve the weight saving and heat load reduction of the SMES coil, the authors applied the force-balanced coil (FBC) configuration to minimize the required mass of structures. Cryocoolers cool the SMES coil composed of MgB$_{2}$ Rutherford cables with a temperature range of 10 K to 20 K. The layout of the compressors requires at least 1 m away from the SMES coil due to the leakage magnetic field. The heat load calculation results show that the mobile SMES keeps over 90% of the energy cycle efficiency during the on-site eigenvalue measurement. Moreover, from the calculation results on the thermal time constant and the re-cooling time of the SMES coil, the eigenvalue measurement can immediately be restarted with the reduced power of SMES in urban areas. The eigenvalue measurement intervals in the suburbs will be every two days.


  • Feasibility Study on a Real-Scale High-Frequency Electromagnets for Magnetic Hyperthermia Base on a Magnetic Scaling Law

    by Hang Xu, Hiroharu Kamada, Takanori Isobe, Shinichi Nomura

    For effective induction heating properties of cancer therapy, the high-frequency electromagnet systems target specifications are 0.064 T of the peak magnetic flux density with 114 kHz of the operating frequency at the center of the used space. The objective of this work is to give a high-precision design method for magnetic Hyperthermia high-frequency electromagnet includes the self-inductance calculation model, the center magnetic flux density calculation model, and power loss analysis. In addition to this, the proposed design method was tested compared to the experimentally measured results of a magnet prototype. At last, the authors summarize the final design of the real-size high-frequency electromagnet for magnetic hyperthermia. From the results, the electromagnet is designed using 201-A Lize wires coil windings and a magnetic core created with PC40 core material. The total power loss and one-turn voltage of the coil windings are 1.2 MW and 22.2 kV, respectively. It means that the coolant for the electromagnet requires high specific heat and high dielectric strength.


  • A Simple Calculation Method for Center Magnetic Flux Density of a Magnetic Core Electromagnet With a Wide Air Gap

    by Hang Xu, Hiroharu Kamada, Shinichi Nomura, Hirotaka Chikaraishi, Hiroaki Tsutsui, Takanori Isobe

    Generally, electromagnet equipment such as an electric transformer is designed with the air gap as narrow as possible for assuming that the magnetic flux in the air gap does not spread. Therefore, it is possible to calculate the magnetic flux density in the air gap of the electromagnet using the magnetic circuit theorem. However, some equipment requires a wide air gap to use the spatial magnetic field. In this case, the magnetic circuit theorem cannot design the electromagnet because of the spread of magnetic flux in the air gap. Then, it becomes difficult to estimate the magnetic reluctance of the wide air gap. Therefore, it is difficult to formulate the center magnetic flux density in the wide air gap. In this work, the authors assume that the wide air gap of the electromagnet can be assembled by an infinite length solenoid with the reverse magnetomotive force finite length solenoid. In this model, the magnetic flux density in the wide air gap can be formulated using the magnetic circuit and the Biot–Savart law. The proposed model was tested in comparison to the experimental results of test electromagnets. The result shows that the proposed model can be used in the engineering design of electromagnets with a wide air gap.


  • Development of 1-T Class Force-Balanced Helical Coils Using REBCO Tapes

    by Hiroharu Kamada, Akira Ninomiya, Shinichi Nomura, Tsuyoshi Yagai, Taketsune Nakamura, Hirotaka Chikaraishi

    The authors proposed the force-balanced helical coils (FBC) concept as a feasibility option for superconducting magnetic energy storage (SMES) using high-temperature superconducting (HTS) tapes. Although the FBC can minimize the mechanical stresses induced by the electromagnetic forces, the FBC has three-dimensional complex shapes of helical winding. Therefore, when the tensile strain and the complex bending strain simultaneously apply to the HTS tapes, the critical current of the HTS coils may decrease irreversibly. The objective of this work is to clarify the critical current property of REBCO tapes depending on the applying complex mechanical strain due to the winding process, the winding configuration and the electromagnetic forces through the development of the HTS-FBC. As a first, design parameters of 1-T class FBC using REBCO tapes and coil winding trajectory were introduced, and the authors discussed the normalized critical current of the HTS-FBC for complex uniaxial strain distribution. The authors also reported a development of a helical winding machine whose motion was optimized to prevent from decreasing the critical current of the HTS tapes during winding process.