Meiyu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Meiyu Wang has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Weibo Hu
College of Electronic Information and Optical Engineering, Nankai University, Tianjin, China
7 shared publications - Yunhui Mei
School of Electrical Engineering, Tiangong University, Tianjin, China
6 shared publications - Guo-Quan Lu
Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, Blacksburg, USA
4 shared publications Haobo Zhang
College of Electronic Information and Optical Engineering, Nankai University, Tianjin, China
3 shared publications- Xin Li
School of Materials Science and Engineering, Tianjin University, Tianjin, China
3 shared publications - Haidong Yan
College of Electrical Engineering, Zhejiang University, Hangzhou, China
2 shared publications
Latest Publications
- 1 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 15 (10) , 2160-2169
Characterization and Mechanism of Silver Sintering on Different Electroless Ni(P) Metallization for Electronics Packaging
As a cutting-edge die attachment technique for electronics packaging, the low-temperature silver (Ag) sintering is attracting increasing interest. Electroless nickel (phosphorus), often known as Ni(P), is a cost-effective and widely used metallization for substrates and baseplates when compared to silver (Ag) or gold (Au). However, oxidation of Ni, low inter-diffusivity and complete immiscibility between Ag and Ni, and complex effects of P content make it challenging to achieve robust sintered-Ag bonding on Ni(P). In this study, IGBT assemblies were packaged for the first time via pressureless sintered-Ag die attachment on electroless Ni(P)-plated substrates featuring different P contents, including 2.74 wt. % of low-P (LP), 7.65 wt. % of medium-P (MP), and 13.10 wt. % of high-P (HP). Afterwards, a comprehensive exploration was firstly conducted regarding the effects of different P content in Ni(P) on the bonding properties. Based on the Ni2p spectra derived from the XPS analysis, the atom ratios of NiO in LP-Ni(P), MP-Ni(P), and HP-Ni(P) are 44.6 at. %, 35.4 at. %, and 20.3 at. %, respectively, indicating the amorphous HP-Ni(P) experiences a lower degree of Ni oxidation than the other two polycrystalline Ni(P) counterparts. Consequently, as the P content increases, there is an enhancement in the mechanical, electrical, and thermal properties. In particular, the high-P Ni(P) yields outstanding results, including a strong bonding strength reaching 39.7 MPa, a small VCE(sat) of 2.00 V close to the 1.99 V of samples using substrates with Ag-plating, and a low Rth_jc of 0.95 °C/W. Furthermore, a deeper investigation into the bonding mechanism between sintered-Ag and Ni(P) has been carried out through chemical and microstructural analyses via EDS, SEM, and TEM. Due to the massive twins within sintered-Ag and reduction of lattice misfit between sintered-Ag and NiO from 2.5% to 0.8%, a robust bonding was achieved by the formation of tightly-knit Ag-NiO-Ni chemical bonds along the (111) crystallographic orientation within the identical face-centered-cubic (FCC) structures. The findings in this study not only contributes to a deeper understanding of the underlying mechanism but also offer valuable guidance for the application of sintered-Ag bonding on Ni(P) metallization in electronics packaging.
- 1 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 15 (10) , 2160-2169
Characterization and Mechanism of Silver Sintering on Different Electroless Ni(P) Metallization for Electronics Packaging
As a cutting-edge die attachment technique for electronics packaging, the low-temperature silver (Ag) sintering is attracting increasing interest. Electroless nickel (phosphorus), often known as Ni(P), is a cost-effective and widely used metallization for substrates and baseplates when compared to silver (Ag) or gold (Au). However, oxidation of Ni, low inter-diffusivity and complete immiscibility between Ag and Ni, and complex effects of P content make it challenging to achieve robust sintered-Ag bonding on Ni(P). In this study, IGBT assemblies were packaged for the first time via pressureless sintered-Ag die attachment on electroless Ni(P)-plated substrates featuring different P contents, including 2.74 wt. % of low-P (LP), 7.65 wt. % of medium-P (MP), and 13.10 wt. % of high-P (HP). Afterwards, a comprehensive exploration was firstly conducted regarding the effects of different P content in Ni(P) on the bonding properties. Based on the Ni2p spectra derived from the XPS analysis, the atom ratios of NiO in LP-Ni(P), MP-Ni(P), and HP-Ni(P) are 44.6 at. %, 35.4 at. %, and 20.3 at. %, respectively, indicating the amorphous HP-Ni(P) experiences a lower degree of Ni oxidation than the other two polycrystalline Ni(P) counterparts. Consequently, as the P content increases, there is an enhancement in the mechanical, electrical, and thermal properties. In particular, the high-P Ni(P) yields outstanding results, including a strong bonding strength reaching 39.7 MPa, a small VCE(sat) of 2.00 V close to the 1.99 V of samples using substrates with Ag-plating, and a low Rth_jc of 0.95 °C/W. Furthermore, a deeper investigation into the bonding mechanism between sintered-Ag and Ni(P) has been carried out through chemical and microstructural analyses via EDS, SEM, and TEM. Due to the massive twins within sintered-Ag and reduction of lattice misfit between sintered-Ag and NiO from 2.5% to 0.8%, a robust bonding was achieved by the formation of tightly-knit Ag-NiO-Ni chemical bonds along the (111) crystallographic orientation within the identical face-centered-cubic (FCC) structures. The findings in this study not only contributes to a deeper understanding of the underlying mechanism but also offer valuable guidance for the application of sintered-Ag bonding on Ni(P) metallization in electronics packaging.
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 892-903
Characterization of Multiple Commercial Sintered-Silver Pastes as Die Attachment for Power Electronics Packaging: Materials, Processing, and Properties
The low-temperature sintered-silver joining has emerged as an advanced die-attach technology for power electronics packaging. However, the industry still has great misgivings to completely adopt this technology. One of the barriers include the confusion of different properties caused by a variety of commercial paste materials and sintering profiles. It is significant to solve this confusion by giving a conclusion and guidance after careful review, selection, characterization, comparison, and analysis of different Ag pastes and sintering profiles. This study firstly made a comprehensive review of commercial Ag paste materials from global suppliers, and then narrowed down 12 Ag pastes from 7 major suppliers, including Alpha, Henkel, Heraeus, Indium, Kyocera, Namics, and NBE Tech. Afterwards, the Ag pastes were processed and characterized from micro and macro aspects. The mechanical, electrical, thermal, and thermomechanical properties were characterized and compared in terms of the formulations of the nano-Ag, micron-Ag, hybrid-Ag, and resin-reinforced Ag pastes, and whether the sintering profiles require pressure or not. Porosity was used to predict the relationship between micromorphology and macroproperty based on modified Gibson-Ashby scaling law. Finally, conclusions and guidance were provided for high-temperature and high-power-density electronics packaging.
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 892-903
Characterization of Multiple Commercial Sintered-Silver Pastes as Die Attachment for Power Electronics Packaging: Materials, Processing, and Properties
The low-temperature sintered-silver joining has emerged as an advanced die-attach technology for power electronics packaging. However, the industry still has great misgivings to completely adopt this technology. One of the barriers include the confusion of different properties caused by a variety of commercial paste materials and sintering profiles. It is significant to solve this confusion by giving a conclusion and guidance after careful review, selection, characterization, comparison, and analysis of different Ag pastes and sintering profiles. This study firstly made a comprehensive review of commercial Ag paste materials from global suppliers, and then narrowed down 12 Ag pastes from 7 major suppliers, including Alpha, Henkel, Heraeus, Indium, Kyocera, Namics, and NBE Tech. Afterwards, the Ag pastes were processed and characterized from micro and macro aspects. The mechanical, electrical, thermal, and thermomechanical properties were characterized and compared in terms of the formulations of the nano-Ag, micron-Ag, hybrid-Ag, and resin-reinforced Ag pastes, and whether the sintering profiles require pressure or not. Porosity was used to predict the relationship between micromorphology and macroproperty based on modified Gibson-Ashby scaling law. Finally, conclusions and guidance were provided for high-temperature and high-power-density electronics packaging.
- 24 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 13086-13098
Bonding and Failure Mechanisms of Sintered-Silver Die-Attach on Electroless Nickel (Phosphorus) Surface Finish for Packaging Power Electronics Modules
The low-temperature silver sintering technology has been increasingly applied for die-attach in power electronics modules. Most reported studies of the technology involved bonding on silver (Ag) or gold (Au) surface finish. Compared to Ag or Au, electroless nickel (phosphorus) or Ni(P) is a cost-effective and widely-used process for surface-finishing module substrates. However, there is a lack of studies on sintered-Ag bonding on the Ni(P) surface. In this study, IGBT devices were bonded using pressureless Ag-sintering on electroless Ni(P)-plated substrates. Micromorphologies and macro-properties were then characterized before and after three reliability tests including high temperature storage life (HTSL), steady-state temperature-humidity bias life (STHBL), and temperature cycling (TC) tests. The as-sintered joints measured strong adhesion of 39 MPa, resulting from Ag-NiO-Ni chemical bonds across the (111) crystal planes with reduced lattice misfit. The Ag-Ni(P) joints exhibited high reliability under high-temperature and thermo-mechanical stress in the HTSL and TC tests, but performed poorly when exposed to high humidity in the STHBL test. The founding in this study helps understand the physical nature of bonding between sintered-Ag and Ni(P), and its failure mechanisms under the influence of different physical stresses.
- 24 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 13086-13098
Bonding and Failure Mechanisms of Sintered-Silver Die-Attach on Electroless Nickel (Phosphorus) Surface Finish for Packaging Power Electronics Modules
The low-temperature silver sintering technology has been increasingly applied for die-attach in power electronics modules. Most reported studies of the technology involved bonding on silver (Ag) or gold (Au) surface finish. Compared to Ag or Au, electroless nickel (phosphorus) or Ni(P) is a cost-effective and widely-used process for surface-finishing module substrates. However, there is a lack of studies on sintered-Ag bonding on the Ni(P) surface. In this study, IGBT devices were bonded using pressureless Ag-sintering on electroless Ni(P)-plated substrates. Micromorphologies and macro-properties were then characterized before and after three reliability tests including high temperature storage life (HTSL), steady-state temperature-humidity bias life (STHBL), and temperature cycling (TC) tests. The as-sintered joints measured strong adhesion of 39 MPa, resulting from Ag-NiO-Ni chemical bonds across the (111) crystal planes with reduced lattice misfit. The Ag-Ni(P) joints exhibited high reliability under high-temperature and thermo-mechanical stress in the HTSL and TC tests, but performed poorly when exposed to high humidity in the STHBL test. The founding in this study helps understand the physical nature of bonding between sintered-Ag and Ni(P), and its failure mechanisms under the influence of different physical stresses.
- 21 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (9) , 1537-1550
Advanced Packaging Technology of GaN HEMT Module for High-Power and High-Frequency Applications: A Review
The GaN HEMT devices have great potential for high-power, high-temperature, and high-frequency applications. However, it is challenging to package GaN HEMTs power module with both low parasitic inductance and thermal resistance, because the lateral GaN HEMTs devices have fast switching speed, high heat-flux density and small die size. This paper made a comprehensive review on the state-of-the-art packaging technologies of GaN HEMTs power modules based on different substrate integration structures, including PCB surface mounting, wire-bonded flip-chip, PCB-embedded, ceramic-substrate integrated, IMS integrated, and hybrid PCB-on-DBC packaging. Each technology has a trade-off among parasitic inductance, thermal performance, and manufacturability. Innovations are still necessary for packaging GaN HEMT modules for their applications in high-frequency and high-power-density converters.1.
- 21 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (9) , 1537-1550
Advanced Packaging Technology of GaN HEMT Module for High-Power and High-Frequency Applications: A Review
The GaN HEMT devices have great potential for high-power, high-temperature, and high-frequency applications. However, it is challenging to package GaN HEMTs power module with both low parasitic inductance and thermal resistance, because the lateral GaN HEMTs devices have fast switching speed, high heat-flux density and small die size. This paper made a comprehensive review on the state-of-the-art packaging technologies of GaN HEMTs power modules based on different substrate integration structures, including PCB surface mounting, wire-bonded flip-chip, PCB-embedded, ceramic-substrate integrated, IMS integrated, and hybrid PCB-on-DBC packaging. Each technology has a trade-off among parasitic inductance, thermal performance, and manufacturability. Innovations are still necessary for packaging GaN HEMT modules for their applications in high-frequency and high-power-density converters.1.
- 3 June 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 150
A hybrid SAR ADC with input range extension
- 3 June 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 150
A hybrid SAR ADC with input range extension
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (19) , 261-276
Review on the through Silicon Via Technology in the 3D-system in Package (3D-SiP)
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (19) , 261-276
Review on the through Silicon Via Technology in the 3D-system in Package (3D-SiP)
- 6 October 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 141
A SAR ADC for multichannel synchronous signal acquisition
- 6 October 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 141
A SAR ADC for multichannel synchronous signal acquisition
- 8 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (2) , 2645-2655
Pressureless Sintered-Silver as Die Attachment for bonding Si and SiC Chips on Silver, Gold, Copper, and Nickel Metallization for Power Electronics Packaging: The Practice and Science
Low-temperature silver (Ag) sintering is emerging as a cutting-edge die-attach technology for power electronics packaging. However, the industry still has concerns about completely accepting this technology. One of the reasons is a lack of knowledge about the mechanism and process of sintered silver bonding on various metallization. Before, we reported a preliminary assessment of the die-shear strength and microstructures of Si dummy device attached on Ag, Au, and Cu metallization. This research will go deeper into the practice and science of attaching Si and SiC devices with sintered-Ag on substrates with up to seven most widely used metallizations, including electroplated Ag, Ni/Au, and Ni, electroless-plated Ni(P)/Ag, Ni(P)/Au, and Ni(P), and native Cu on DBC substrate. All sintered-Ag die-attach were pressureless in the air at temperatures ranging from 220 °C to 300 °C. The mechanical, electrical, and thermal parameters, as well as the microstructural analyses, were assessed. The purpose of this research is to gain a better understanding by: 1) discussing effects of devices and substrate metallizations on the mechanical, electrical, and thermal characteristics; 2) reviewing fundamental mechanisms of interfacial adhesion for sintered-Ag bonding, and 3) providing practical considerations for developing Si and SiC sintered-Ag die-attaching profiles on the widely used substrate metallization.
- 8 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (2) , 2645-2655
Pressureless Sintered-Silver as Die Attachment for bonding Si and SiC Chips on Silver, Gold, Copper, and Nickel Metallization for Power Electronics Packaging: The Practice and Science
Low-temperature silver (Ag) sintering is emerging as a cutting-edge die-attach technology for power electronics packaging. However, the industry still has concerns about completely accepting this technology. One of the reasons is a lack of knowledge about the mechanism and process of sintered silver bonding on various metallization. Before, we reported a preliminary assessment of the die-shear strength and microstructures of Si dummy device attached on Ag, Au, and Cu metallization. This research will go deeper into the practice and science of attaching Si and SiC devices with sintered-Ag on substrates with up to seven most widely used metallizations, including electroplated Ag, Ni/Au, and Ni, electroless-plated Ni(P)/Ag, Ni(P)/Au, and Ni(P), and native Cu on DBC substrate. All sintered-Ag die-attach were pressureless in the air at temperatures ranging from 220 °C to 300 °C. The mechanical, electrical, and thermal parameters, as well as the microstructural analyses, were assessed. The purpose of this research is to gain a better understanding by: 1) discussing effects of devices and substrate metallizations on the mechanical, electrical, and thermal characteristics; 2) reviewing fundamental mechanisms of interfacial adhesion for sintered-Ag bonding, and 3) providing practical considerations for developing Si and SiC sintered-Ag die-attaching profiles on the widely used substrate metallization.
- 21 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (10) , 9945-9955
A High Dynamic Range Vibration Radar Sensor With Automatic DC Voltage Extraction
One challenge of using a homodyne receiver to obtain accurate vibration information is the undesired DC voltage in a continuous wave radar. It reduces the output dynamic range and even saturates the signal path. In this paper, an adaptive DC extraction method with flexible clocks is proposed in a 5.8 GHz Doppler radar to separate the DC component from the input signal. Rather than simply eliminating the DC component, the proposed method digitizes the DC component as well as the input AC signal with a large dynamic range. It is accomplished by a mixed-signal feedback loop and features an excellent accommodation to large input DC variations and flexible settling time. In the loop, a closed-loop amplifier is used as the input stage and an ADC is followed to digitize the amplified quadrature signals from the radar. Afterward, a simplified digital filter is cascaded to extract the digital version of the DC component and feedback to the input stage. In this way, both the DC component and AC component in the input signal are separated and digitized without saturation. For verification, several simulations and experiments were conducted. The results show that a wide DC range can be tolerated and extracted. What’s more, the target motion with sub-millimeter amplitude can be successfully captured based on the proposed DC extraction loop.
- 21 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (10) , 9945-9955
A High Dynamic Range Vibration Radar Sensor With Automatic DC Voltage Extraction
One challenge of using a homodyne receiver to obtain accurate vibration information is the undesired DC voltage in a continuous wave radar. It reduces the output dynamic range and even saturates the signal path. In this paper, an adaptive DC extraction method with flexible clocks is proposed in a 5.8 GHz Doppler radar to separate the DC component from the input signal. Rather than simply eliminating the DC component, the proposed method digitizes the DC component as well as the input AC signal with a large dynamic range. It is accomplished by a mixed-signal feedback loop and features an excellent accommodation to large input DC variations and flexible settling time. In the loop, a closed-loop amplifier is used as the input stage and an ADC is followed to digitize the amplified quadrature signals from the radar. Afterward, a simplified digital filter is cascaded to extract the digital version of the DC component and feedback to the input stage. In this way, both the DC component and AC component in the input signal are separated and digitized without saturation. For verification, several simulations and experiments were conducted. The results show that a wide DC range can be tolerated and extracted. What’s more, the target motion with sub-millimeter amplitude can be successfully captured based on the proposed DC extraction loop.
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 616-621
Re-fusion of Inertial Attitude Measurement Sensors Based on Phase-lag-free LPF and Kalman Filter
The high-quality signal is the basis of motion control. Gyroscope is an important sensor in feedback loop of inertial stabilization control. However, accumulative errors exist in attitude calculation by gyroscope because of gyro drift. In general, Kalman filter is used as fusing the output of gyroscopes and accelerometers to suppress gyro drift. This method will bring phase lag deviation because it does not consider the change of angular acceleration in actual motion. Therefore, a re-fusion method based on phase-lag-free low pass filter(LPF) and Kalman filter is proposed. The simulation and experimental results show that the re-fusion method proposed in this paper integrates the output data of different sensors, which has obvious ability to suppress phase lag and has a certain filtering performance on the basis of suppressing gyro drift.
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 616-621
Re-fusion of Inertial Attitude Measurement Sensors Based on Phase-lag-free LPF and Kalman Filter
The high-quality signal is the basis of motion control. Gyroscope is an important sensor in feedback loop of inertial stabilization control. However, accumulative errors exist in attitude calculation by gyroscope because of gyro drift. In general, Kalman filter is used as fusing the output of gyroscopes and accelerometers to suppress gyro drift. This method will bring phase lag deviation because it does not consider the change of angular acceleration in actual motion. Therefore, a re-fusion method based on phase-lag-free low pass filter(LPF) and Kalman filter is proposed. The simulation and experimental results show that the re-fusion method proposed in this paper integrates the output data of different sensors, which has obvious ability to suppress phase lag and has a certain filtering performance on the basis of suppressing gyro drift.