Kishwar Mashooq
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kishwar Mashooq has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jaesung Jo
Department of Electrical Engineering and Computer Science, University of Michigan 1 , 1301 Beal Avenue, Ann Arbor, Michigan 48109, USA
3 shared publications - Rebecca Lorenz Peterson
University of Michigan 4 , Ann Arbor, Michigan 48109
3 shared publications - Thomas Szkopek
McGill University
1 shared publication - Xianhe Liu
Electrical and Computer Engineering, McGill University, Montreal, Quebec Canada
1 shared publication - Zetian Mi
Department of Electrical Engineering and Computer Science University of Michigan Ann Arbor Michigan USA
1 shared publication
Latest Publications
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (1) , 574-580
Effect of Metal Capping Layer in Achieving Record High p-Type SnO Thin Film Transistor Mobility
Recently p-type tin monoxide (SnO) thin film transistors (TFTs) have drawn significant interest for use in all-oxide CMOS circuits for back-end-of-line (BEOL) integration with Si and flexible electronics. However, most SnO TFTs demonstrated so far have a limited field effect mobility and poor ON–OFF current ratio. Here, we used a floating metal cap layer to create a bilayer TFT structure and boost the device’s effective mobility. We achieved a record high p-type SnO TFT mobility of 19.1 cm $^{\text{2}}$ V $^{\text{-1}}$ s $^{\text{-1}}$ using a Ni/Au capping layer to cover a portion of the active channel. By comparing the experiment and TCAD simulation, we explained the working mechanism of the SnO bilayer TFT. We also investigated the effect of layer thickness on TFT electrical performance. A thin SnO active layer is desired to minimize the vertical resistance in the ON-state and thereby increase the effective TFT mobility. Finally, by applying appropriate surface passivation we demonstrated an $\sim$ 8 $\times$ improvement in the ON–OFF current ratio of our SnO bilayer TFTs. By combining the use of a floating metal capping layer and surface passivation, we can significantly and simultaneously improve both the effective mobility and the ON–OFF current ratio of SnO TFTs. In addition, we showed that SnO bilayer TFTs exhibit more robust behavior to gate-bias stress compared to traditional SnO TFTs.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (1) , 574-580
Effect of Metal Capping Layer in Achieving Record High p-Type SnO Thin Film Transistor Mobility
Recently p-type tin monoxide (SnO) thin film transistors (TFTs) have drawn significant interest for use in all-oxide CMOS circuits for back-end-of-line (BEOL) integration with Si and flexible electronics. However, most SnO TFTs demonstrated so far have a limited field effect mobility and poor ON–OFF current ratio. Here, we used a floating metal cap layer to create a bilayer TFT structure and boost the device’s effective mobility. We achieved a record high p-type SnO TFT mobility of 19.1 cm $^{\text{2}}$ V $^{\text{-1}}$ s $^{\text{-1}}$ using a Ni/Au capping layer to cover a portion of the active channel. By comparing the experiment and TCAD simulation, we explained the working mechanism of the SnO bilayer TFT. We also investigated the effect of layer thickness on TFT electrical performance. A thin SnO active layer is desired to minimize the vertical resistance in the ON-state and thereby increase the effective TFT mobility. Finally, by applying appropriate surface passivation we demonstrated an $\sim$ 8 $\times$ improvement in the ON–OFF current ratio of our SnO bilayer TFTs. By combining the use of a floating metal capping layer and surface passivation, we can significantly and simultaneously improve both the effective mobility and the ON–OFF current ratio of SnO TFTs. In addition, we showed that SnO bilayer TFTs exhibit more robust behavior to gate-bias stress compared to traditional SnO TFTs.
- 2 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (1) , 013504
Demonstration and analysis of ambipolar SnO inverter with high gain
Ambipolar materials offer a unique and simple route toward cost-effective complementary thin film circuits. SnO is one of the few metal oxide semiconductors that demonstrates ambipolar behavior. In this work, we demonstrated an ambipolar SnO inverter with record high inverter gain and corroborated our experimental results with a comprehensive analytical model. First, we developed ambipolar SnO thin film transistors (TFTs) with symmetric p-type and n-type conduction. Using these ambipolar SnO TFTs, we fabricated ambipolar SnO inverters. Our ambipolar SnO inverter shows a record gain of 432 (V/V), which is the highest reported among all ambipolar material systems. To understand our high inverter gain, we developed a comprehensive analytical model to analyze the transition region of an ambipolar inverter. Our analytical model showed an excellent match with our experiment results. Furthermore, our analytical model shows that to achieve a high inverter gain and a voltage transition point in the middle of the supply voltage range, we must minimize channel length modulation and match the p- and n-type behaviors of the ambipolar TFTs. By expanding our understanding of ambipolar inverter behavior, this work highlights the possibilities of ambipolar SnO TFTs for future high performance complementary thin film circuits.
- 2 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (1) , 013504
Demonstration and analysis of ambipolar SnO inverter with high gain
Ambipolar materials offer a unique and simple route toward cost-effective complementary thin film circuits. SnO is one of the few metal oxide semiconductors that demonstrates ambipolar behavior. In this work, we demonstrated an ambipolar SnO inverter with record high inverter gain and corroborated our experimental results with a comprehensive analytical model. First, we developed ambipolar SnO thin film transistors (TFTs) with symmetric p-type and n-type conduction. Using these ambipolar SnO TFTs, we fabricated ambipolar SnO inverters. Our ambipolar SnO inverter shows a record gain of 432 (V/V), which is the highest reported among all ambipolar material systems. To understand our high inverter gain, we developed a comprehensive analytical model to analyze the transition region of an ambipolar inverter. Our analytical model showed an excellent match with our experiment results. Furthermore, our analytical model shows that to achieve a high inverter gain and a voltage transition point in the middle of the supply voltage range, we must minimize channel length modulation and match the p- and n-type behaviors of the ambipolar TFTs. By expanding our understanding of ambipolar inverter behavior, this work highlights the possibilities of ambipolar SnO TFTs for future high performance complementary thin film circuits.
- 11 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (5) , 2436-2442
Extraction of SnO Subbandgap Defect Density by Numerical Modeling of p-Type TFTs
Recently, p-type tin monoxide (SnO) thin-film transistors (TFTs) have gained interest for all-oxide complementary metal–oxide semiconductor (CMOS) circuits for flexible electronics and back-end-of-line integration with Si. However, most SnO TFTs demonstrated so far exhibit a low on– off-current ratio and limited field effect mobility. To understand and improve SnO TFT performance, it is necessary to quantitatively characterize the subbandgap defects in SnO and at its dielectric interface. In this work, we establish numerical models which provide this understanding. By concurrent fitting of simulated ${I}_{\text{D}}$ – ${V}_{\text{GS}}$ and effective mobility versus ${V}_{\text{GS}}$ to experimentally measured data, we can accurately extract SnO defect state profiles. Using the extracted simulation models, we then identify ways to improve SnO TFT performance. Specifically, a reduction in the density of shallow, bulk Gaussian acceptor states, is necessary to reduce the off-current, while reducing the contact resistance and interface donor-like tail state density can improve the SnO field effect mobility.
- 11 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (5) , 2436-2442
Extraction of SnO Subbandgap Defect Density by Numerical Modeling of p-Type TFTs
Recently, p-type tin monoxide (SnO) thin-film transistors (TFTs) have gained interest for all-oxide complementary metal–oxide semiconductor (CMOS) circuits for flexible electronics and back-end-of-line integration with Si. However, most SnO TFTs demonstrated so far exhibit a low on– off-current ratio and limited field effect mobility. To understand and improve SnO TFT performance, it is necessary to quantitatively characterize the subbandgap defects in SnO and at its dielectric interface. In this work, we establish numerical models which provide this understanding. By concurrent fitting of simulated ${I}_{\text{D}}$ – ${V}_{\text{GS}}$ and effective mobility versus ${V}_{\text{GS}}$ to experimentally measured data, we can accurately extract SnO defect state profiles. Using the extracted simulation models, we then identify ways to improve SnO TFT performance. Specifically, a reduction in the density of shallow, bulk Gaussian acceptor states, is necessary to reduce the off-current, while reducing the contact resistance and interface donor-like tail state density can improve the SnO field effect mobility.
- Open Access
- 21 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (4) , 1-11
Improving the Efficiency of Transverse Magnetic Polarized Emission from AlGaN Based LEDs by Using Nanowire Photonic Crystal
AlGaN-based deep ultraviolet (UV) light emitting diodes (LEDs) are attractive for a wide range of applications. To date, however, the best reported external quantum efficiency (EQE) for LEDs operating in the wavelength range of ~240 nm is well below 1%. In this work, we have performed detailed studies of the EQE of AlGaN nanowire photonic crystal LEDs in this wavelength range by finite difference time domain simulation. By coupling in-plane emission to vertical emission, light extraction efficiency (LEE) over 90% can, in principle, be expected from the device top surface for transverse magnetic polarized photons that was not previously possible in conventional planar quantum well devices. Taken into account practical limitations including the absorptive p-Al(Ga)N contact and the presence of metal contact grid, LEE in the range of 30-40% is also expected. Moreover, due to the Purcell effect, the radiative recombination rate and therefore internal quantum efficiency (IQE) can be significantly modified in nanowire photonic crystal structures. We have established the design principles and ultimate efficiency limit of AlGaN nanowire photonic crystal LEDs: For AlGaN LEDs with very high IQE, EQE >70% can, in principle, be expected by operating near the - point of nanowire photonic crystals, whereas for structures with relatively low IQE it is preferred to operate near the M point to enhance the IQE while maintaining reasonably high LEE.
- 21 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (4) , 1-11
Open AccessImproving the Efficiency of Transverse Magnetic Polarized Emission from AlGaN Based LEDs by Using Nanowire Photonic Crystal
AlGaN-based deep ultraviolet (UV) light emitting diodes (LEDs) are attractive for a wide range of applications. To date, however, the best reported external quantum efficiency (EQE) for LEDs operating in the wavelength range of ~240 nm is well below 1%. In this work, we have performed detailed studies of the EQE of AlGaN nanowire photonic crystal LEDs in this wavelength range by finite difference time domain simulation. By coupling in-plane emission to vertical emission, light extraction efficiency (LEE) over 90% can, in principle, be expected from the device top surface for transverse magnetic polarized photons that was not previously possible in conventional planar quantum well devices. Taken into account practical limitations including the absorptive p-Al(Ga)N contact and the presence of metal contact grid, LEE in the range of 30-40% is also expected. Moreover, due to the Purcell effect, the radiative recombination rate and therefore internal quantum efficiency (IQE) can be significantly modified in nanowire photonic crystal structures. We have established the design principles and ultimate efficiency limit of AlGaN nanowire photonic crystal LEDs: For AlGaN LEDs with very high IQE, EQE >70% can, in principle, be expected by operating near the - point of nanowire photonic crystals, whereas for structures with relatively low IQE it is preferred to operate near the M point to enhance the IQE while maintaining reasonably high LEE.