WMWladyslaw Mitianiec

Wladyslaw Mitianiec

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wladyslaw Mitianiec has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study of influence of boundary conditions on deformation and stresses in a cooled piston of a diesel engine – part A - mathematical models

    by W Mitianiec

    The paper presents influence of boundary conditions on mechanical and thermal stresses of an oil cooled piston in diesel engine Scania DC09 074A and its deformation due to high combustion pressure and variable temperature. Due to different fixing of the pin in the piston hub the deformation of the piston shape and von Misses stresses differ at the same boundary conditions. This part of paper describes mathematical model of the piston load especially of heat transfer to wall taking into account three elements: convection, radiation and conductivity of the piston material. Calculations of the piston loads were carried out by using 0D mathematical model at assumption of the Vibe combustion model and the Woschni heat transfer model for homogenous mixture. For precise determination of the gas temperature in the combustion chamber the CFD technique recently is used and for that case the simulation of compression, combustion and expansion processes was carried out by using the program Fluent. The numerical calculations were done for two kinds of fuel: diesel oil and CNG due to possibility of changing the oil fuelling system into gaseous fuelling system. In order to proper work of CNG engine the compression ratio should be decreased. This was done by reducing the volume of the combustion chamber. Most calculations have done by researchers at assumption that the piston hubs are fixed, but it is not right assumption. In summary the paper gives indications how to set boundary conditions for "floating" piston pin. The paper presents shortly mathematical model of heat balance in the piston and FEM solution of stresses and deformation which are based on strains. This study is an introduction to calculations showed in the part B.

  • Open Access

    Modern Pneumatic and Combustion Hybrid Engines

    by Wladyslaw Mitianiec

    This chapter presents the possibility of use of the pneumatic piston engine with two-stroke cycle or four stroke-cycle of the work as an alternative driving source or additional power for the battery regeneration in the electric vehicles. Additionally, such engine can work together with combustion engine as a drive unit in a road vehicle. During city driving, such engine is driven by compressed air. The energy for the engine work is taken from the energy of the air stored at high pressure (about 30 MPa) in bottles or tanks. The chapter presents the thermodynamic theory included in the mathematical model of the engine based on thermodynamic processes (mass and energy balance). On such considerations, the chapter shows the results obtained from specially written computer program for the determination of the most important factors. The results of the calculations are included in the graphs showing the influence of the control parameters (air pressure, injection timing and rotational speed) on the engine working parameters. Certain chapters concern to a hybrid combustion system with an air injection only for a compression ignition engine in order to achieve higher indicated mean pressure and lower fuel consumption.


  • Co-Combustion of Pulverized Coal and Biomass in Fluidized Bed of Furnace

    by Mitianiec Wladyslaw

    Combustion processes of two fuels, pulverized coal and biomass, in furnaces take place at steady state. Combustion of condensed fuels involves one-way interfacial flux due to phenomena in the condensed phase (evaporation or pyrolysis) and reciprocal ones (heterogeneous combustion and gasification). Many of the species injected in the gas phase are later involved in gas phase combustion. This paper presents results of combustion process of two-phase charge contained coal and wetted biomass, where the carrier was the air with given flow rate. The furnace has three inlets with assumed inlet flow rate of coal, biomass, and air, and combustion process takes place in the furnace fluidized space. The simulation of such combustion process was carried out by numerical code of open source computational fluid dynamics (CFD) program code_saturne. For both fuels, the moist biomass with following mass contents: C = 53%, H = 5.8%, O = 37.62%, ash = 3.6, and mean diameter of molecules equal to 0.0008 m and pulverized coal with following mass contents: C = 76.65%, H = 5.16%, O = 9.9%, ash = 6.21%, and mean molecule diameter 0.000025 m were used. Devolatilization process with kinetic reactions was taken into account. Distribution of the main combustion product in furnace space is presented with disappearance of the molecules of fuels. This paper presents theoretical description of the two-phase charge, specification of the thermodynamic state of the charge in inlet boundaries and furnace space, and thermal parameters of solid fuel molecules obtained from the open source postprocessor paraview.


  • Open Access

    Scientific Conference on Automotive Vehicles and Combustion Engines (KONMOT 2016)

    by Marek Brzezanski, Wladyslaw Mitianiec

    22-23 September 2016, Cracow, Poland The contemporary world requires ecological solutions in the area of automotive vehicles, low energy consumption, safety and easy exploitation. The role of engineers and scientists is the realization and managing of the designing and exploitation processes within that area. The growing exploitation and ecological demands set successive challenges for designers and scientists in the area of automobiles, powertrains and exploitation. Particularly the essential problem is finding solutions decreasing fuel consumption and emission of the exhaust gases as well as application of the alternative powertrains such as hybrid and electric. The cyclical automotive conference KONMOT since 1976 is a place of meeting of outstanding scientists and engineers from country and abroad, raising contemporary problems of motorization with the possibility of publishing results on the international area. In 2016 the organized automotive conference KONMOT celebrated the 40th anniversary. It was organized by the Institute of Automobiles and Internal Combustion Engines in Cracow University of Technology (CUT). The first conference was held in Kroscienko-Szczawnica on 20-23 September 1976. The motto, that guided the deliberations, was "Progress in Research of Motor Vehicle." The conference was a nationwide and attended by many representatives of technical universities, research and development centres and plants related to the automotive industry. In the years 2000, 2004 and 2008, a conference was called KONMOT-AUTOPROGRES, the main organizer was the Cracow University of Technology. In 2002 and 2006 the main organizer of the conference was Automotive Industry Institute in Warsaw and the conference was called AUTOPROGRES-KONMOT. Papers presented on every two years conference KONMOT were published in the journal issued by the Polish Academy of Sciences "Portfolio of Science and the Problem Committee on Motorization" or published by the Technical Journal issued by CUT, as well as in the form of monographs. Some of the conferences were dedicated to the jubilee of work of outstanding scientific specialists in the automotive and engines fields. Apart from the official agenda for the conference the gala dinners were organized for all participants, often headline performances by famous artists were important point of such meetings. The penultimate conference KONMOT was held on 25-26 September 2014 in Cracow under the slogan "Development of vehicles - construction, operation, ecology and safety." The organized scientific conference KONMOT-2016 as in previous years provided an excellent opportunity to showcase of achievements of researchers and scientists and exchange of experience for a wide range of activity in research and development centres, industrial areas and universities. With regards to the current conference we are delighted to come up with ninety two (92) contributed research papers selected from the proceedings, as an output of the Scientific Automotive Conference KONMOT 2016 on motor-cars and engines progress held in Cracow (Poland) from September 22-23, 2016. This event marks as previous meetings in a highly successful series of conference devoted to this important technical field. Conference KONMOT gathers industrial and scientific communities in the field of design, experimental research and modelling of all scientific and industrial sectors of automotive branch. Contributions cover a wide range of topics including design and modelling of the suspension, traction and new driving systems in automobiles, method of vehicles exploitation or tribology. The new driving systems require a new design of engines for better efficiency and lower exhaust gas emission. Thirty three papers describe the research, experimental investigations and modelling of combustion processes in combustion engines. The papers shown during KONMOT 2016 from both the oral presentation and poster sessions are included in this conference volume. They are divided into the following three topic areas: Design and Research of Automobiles, Exploitation of Automobiles and Internal Combustion Engines and Emission. More than one third of the papers are directly concerned with mathematical modelling and numerical simulation in automobiles and internal combustion engines. However, most of papers include experimental and industrial activity. Some of the papers concern the applying of special new materials and were included in the Exploitation topic. The conference co-chairmen are grateful to the scientific committee and all the reviewers of the papers for their efficient work done in a very short period of time. These proceedings would not have been possible without the tremendous help of Mr Dr Eng. Marcin Noga and Mrs MSc Magdalena Kalarus from the Cracow University of Technology. Thanks also to CUT Publishing House for preparing of special issue of conference abstracts. Finally, we would like to thank our sponsors for their financial support, without that the conference would not be so attractive for participants, such as Development and Research Institute BOSMAL in Bielsko Biala, AVL - Poland Branch, FEV Poland, EC Engineering, Horus-Energia and Polish Scientific Society of Combustion Engines (PTNSS) and others. The logos of our main sponsors are shown below. We invite all participants from whole the world to the next conference KONMOT 2018.


  • Open Access

    Assessment of total efficiency in adiabatic engines

    by Shi Run-Hua, Huang Liu-Sheng, Yang Wei, M Sudarshan, R Singh, Sun Heng-Xin, Zun-Long Liu, Liu Kui, H L Liu, M M Liu, et al.

    The paper presents influence of ceramic coating in all surfaces of the combustion chamber of SI four-stroke engine on working parameters mainly on heat balance and total efficiency. Three cases of engine were considered: standard without ceramic coating, fully adiabatic combustion chamber and engine with different thickness of ceramic coating. Consideration of adiabatic or semi-adiabatic engine was connected with mathematical modelling of heat transfer from the cylinder gas to the cooling medium. This model takes into account changeable convection coefficient based on the experimental formulas of Woschni, heat conductivity of multi-layer walls and also small effect of radiation in SI engines. The simulation model was elaborated with full heat transfer to the cooling medium and unsteady gas flow in the engine intake and exhaust systems. The computer program taking into account 0D model of engine processes in the cylinder and 1D model of gas flow was elaborated for determination of many basic engine thermodynamic parameters for Suzuki DR-Z400S 400 cc SI engine. The paper presents calculation results of influence of the ceramic coating thickness on indicated pressure, specific fuel consumption, cooling and exhaust heat losses. Next it were presented comparisons of effective power, heat losses in the cooling and exhaust systems, total efficiency in function of engine rotational speed and also comparison of temperature inside the cylinder for standard, semi-adiabatic and full adiabatic engine. On the basis of the achieved results it was found higher total efficiency of adiabatic engines at 2500 rpm from 27% for standard engine to 37% for full adiabatic engine.