Shuyi Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shuyi Huang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Weiguo Xu
Tsinghua University
2 shared publications Benjamin Dillenburger
ETH Zurich
1 shared publication- Hanyang Hu
Tsinghua University, Beijing, China
1 shared publication Kai Hsun Yeh
ETH Zurich
1 shared publication- Karen Antorveza Paez
ETH Zurich
1 shared publication Kevin Seav
ETH Zurich
1 shared publication
Latest Publications
- Open Access
- 16 July 2026
- Published by Cambridge University Press (CUP) in Biotechnology Design
- Vol. 4, e40
Design workflow for porous 3D-printed biocement geometries
Microbially induced calcium carbonate precipitation (MICP) offers a low-energy, carbon-efficient alternative to traditional mineral material production, yet its integration into digital fabrication for architectural applications remains limited. This research presents a design-to-biofabrication workflow that combines computational geometry, robotic extrusion-based 3D printing and MICP. The study introduces a methodology that uses porosity, surface-area-to-volume (SA/V) ratio, interlayer connectivity and overhang capacity as coupled design parameters that balance biocementation requirements and fabrication constraints. Through iterative testing of triply periodic minimal surfaces (TPMSs) geometries, an “Optimized Unit” was developed and refined to improve printability and biomineralization efficiency. The workflow is validated through a 1 m 2 architectural partition wall demonstrator that illustrates the potential for modular biomineralized architectural components. The results show that calibrated geometric control enables stable extrusion while enhancing mineral distribution, demonstrating a pathway towards architecturally scaled bio-fabricated mineral components.
- 16 July 2026
- Published by Cambridge University Press (CUP) in Biotechnology Design
- Vol. 4, e40
Open AccessDesign workflow for porous 3D-printed biocement geometries
Microbially induced calcium carbonate precipitation (MICP) offers a low-energy, carbon-efficient alternative to traditional mineral material production, yet its integration into digital fabrication for architectural applications remains limited. This research presents a design-to-biofabrication workflow that combines computational geometry, robotic extrusion-based 3D printing and MICP. The study introduces a methodology that uses porosity, surface-area-to-volume (SA/V) ratio, interlayer connectivity and overhang capacity as coupled design parameters that balance biocementation requirements and fabrication constraints. Through iterative testing of triply periodic minimal surfaces (TPMSs) geometries, an “Optimized Unit” was developed and refined to improve printability and biomineralization efficiency. The workflow is validated through a 1 m 2 architectural partition wall demonstrator that illustrates the potential for modular biomineralized architectural components. The results show that calibrated geometric control enables stable extrusion while enhancing mineral distribution, demonstrating a pathway towards architecturally scaled bio-fabricated mineral components.
- Open Access
- 29 June 2023
- Published by Springer Nature in Architectural Intelligence
- Vol. 2 (1) , 1-15
Space-filling and print path generation methods for large-area 3D concrete printing pavements
3D concrete printing (3DCP) technology is a construction method that offers a unique combination of automation and customization. However, when the printing area goes large, generating the print path becomes a sophisticated work. That’s because the customized print path should not only be expandable but also printable, such rules are hard to follow as both the printing area and construction requirements increase. In this paper, the Shenzhen Baoan 3D Printing Park project serves as a case study to introduce space-filling and print path generation methods for three types of large-area concrete pavement. The space-filling methods utilize geometry-based rules to generate complex and expandable paving patterns, while the print path generation methods utilize construction-oriented rules to convert these patterns into print paths. The research provides easy-to-operate design and programming workflows to achieve a pavement printing area of 836 sqm, which significantly increases the construction scale of large-format additive manufacturing (LFAM) and shows the potential of 3D printing technology to reach non-standard results by using standard workflows.
- 29 June 2023
- Published by Springer Nature in Architectural Intelligence
- Vol. 2 (1) , 1-15
Open AccessSpace-filling and print path generation methods for large-area 3D concrete printing pavements
3D concrete printing (3DCP) technology is a construction method that offers a unique combination of automation and customization. However, when the printing area goes large, generating the print path becomes a sophisticated work. That’s because the customized print path should not only be expandable but also printable, such rules are hard to follow as both the printing area and construction requirements increase. In this paper, the Shenzhen Baoan 3D Printing Park project serves as a case study to introduce space-filling and print path generation methods for three types of large-area concrete pavement. The space-filling methods utilize geometry-based rules to generate complex and expandable paving patterns, while the print path generation methods utilize construction-oriented rules to convert these patterns into print paths. The research provides easy-to-operate design and programming workflows to achieve a pavement printing area of 836 sqm, which significantly increases the construction scale of large-format additive manufacturing (LFAM) and shows the potential of 3D printing technology to reach non-standard results by using standard workflows.
- Open Access
- 1 January 2023
- Published by Education and Research in Computer Aided Architectural Design in Europe (eCAADe)
Improving the Overhang of 3D-printed Concrete Shells by Wrinkle Structures
The labour shortage is impacting the construction industry globally, and 3D concrete printing (3DCP) technology is considered a solution for such an issue by using robots instead of manpower in building construction. However, due to the unstable mechanical properties of the fresh-state concrete, current 3DCP building forms exclude a massive number of options, one of them being the overhang shape. Therefore, this paper introduces bionic wrinkles to improve the overhang of 3DCP shell prototypes and demonstrates the feasibility of this idea through three groups of buckling simulations. This study proves that surface wrinkles can improve the in-process mechanical properties as well as the overhang capacity of shell structures. In the best scenario, the original design which only reached 30° overhang can be promoted to 77.5°. Besides, the applications of all wrinkle types are robust.
- 1 January 2023
- Published by Education and Research in Computer Aided Architectural Design in Europe (eCAADe)
Open AccessImproving the Overhang of 3D-printed Concrete Shells by Wrinkle Structures
The labour shortage is impacting the construction industry globally, and 3D concrete printing (3DCP) technology is considered a solution for such an issue by using robots instead of manpower in building construction. However, due to the unstable mechanical properties of the fresh-state concrete, current 3DCP building forms exclude a massive number of options, one of them being the overhang shape. Therefore, this paper introduces bionic wrinkles to improve the overhang of 3DCP shell prototypes and demonstrates the feasibility of this idea through three groups of buckling simulations. This study proves that surface wrinkles can improve the in-process mechanical properties as well as the overhang capacity of shell structures. In the best scenario, the original design which only reached 30° overhang can be promoted to 77.5°. Besides, the applications of all wrinkle types are robust.
- Open Access
- 1 August 2022
- Published by KEAI Publishing in Frontiers of Architectural Research
- Vol. 11 (4) , 653-669
The impacts of fabrication systems on 3D concrete printing building forms
- 1 August 2022
- Published by KEAI Publishing in Frontiers of Architectural Research
- Vol. 11 (4) , 653-669
Open AccessThe impacts of fabrication systems on 3D concrete printing building forms