Qizhong Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qizhong Huang has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
- Mingyu Zhang
National Key Laboratory of Science and Technology on High-strength Structural Materials, Central South University, Changsha 410083, China
7 shared publications - Zhiyong Xie
Institute of Powder Metallurgy, Central South University, Changsha 410083, China
7 shared publications - Xin Yang
National Key Laboratory of Science and Technology on High-strength Structural Materials, Central South University, Changsha, People’s Republic of China
5 shared publications Xin Yang
Central South University
4 shared publications- Zhean Su
National Key Laboratory of Science and Technology on High-strength Structural Materials, Central South University, Changsha 410083, China
4 shared publications Min Sun
State Key Laboratory for Powder Metallurgy, Central South University, Changsha 410083, P. R. China
3 shared publications
Latest Publications
- 23 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 623
Self-supporting multi-carbon composites assist recycled-silicon for high-performance lithium storage
- 23 September 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 623
Self-supporting multi-carbon composites assist recycled-silicon for high-performance lithium storage
- 1 April 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (4) , 1-14
Micro and nanoarchitectonics of ZrC filler with size effects on densification and ablative mechanism of C/C-SiC-ZrC composites
- 1 April 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (4) , 1-14
Micro and nanoarchitectonics of ZrC filler with size effects on densification and ablative mechanism of C/C-SiC-ZrC composites
- Open Access
Preparation of HfCxN1−x Nanoparticles Derived from a Multifunction Precursor with Hf-O and Hf-N Bonds
HfCxN1−x nanoparticles were synthesized using the urea-glass route, employing hafnium chloride, urea, and methanol as raw materials. The synthesis process, polymer-to-ceramic conversion, microstructure, and phase evolution of HfCxN1−x/C nanoparticles were thoroughly investigated across a wide range of molar ratios between the nitrogen source and the hafnium source. Upon annealing at 1600 °C, all precursors demonstrated remarkable translatability to HfCxN1−x ceramics. Under high nitrogen source ratios, the precursor exhibited complete transformation into HfCxN1−x nanoparticles at 1200 °C, with no observed presence of oxidation phases. In comparison to HfO2, the carbothermal reaction of HfN with C significantly reduced the preparation temperature required for HfC. By increasing the urea content in the precursor, the carbon content of the pyrolyzed products increased, leading to a substantial decrease in the electrical conductivity of HfCxN1−x/C nanoparticle powders. Notably, as the urea content in the precursor increased, a significant decrease in average electrical conductivity values was observed for the R4-1600, R8-1600, R12-1600, and R16-1600 nanoparticles measured at a pressure of 18 MPa, yielding values of 225.5, 59.1, 44.8, and 46.0 S·cm−1, respectively.
Open AccessPreparation of HfCxN1−x Nanoparticles Derived from a Multifunction Precursor with Hf-O and Hf-N Bonds
HfCxN1−x nanoparticles were synthesized using the urea-glass route, employing hafnium chloride, urea, and methanol as raw materials. The synthesis process, polymer-to-ceramic conversion, microstructure, and phase evolution of HfCxN1−x/C nanoparticles were thoroughly investigated across a wide range of molar ratios between the nitrogen source and the hafnium source. Upon annealing at 1600 °C, all precursors demonstrated remarkable translatability to HfCxN1−x ceramics. Under high nitrogen source ratios, the precursor exhibited complete transformation into HfCxN1−x nanoparticles at 1200 °C, with no observed presence of oxidation phases. In comparison to HfO2, the carbothermal reaction of HfN with C significantly reduced the preparation temperature required for HfC. By increasing the urea content in the precursor, the carbon content of the pyrolyzed products increased, leading to a substantial decrease in the electrical conductivity of HfCxN1−x/C nanoparticle powders. Notably, as the urea content in the precursor increased, a significant decrease in average electrical conductivity values was observed for the R4-1600, R8-1600, R12-1600, and R16-1600 nanoparticles measured at a pressure of 18 MPa, yielding values of 225.5, 59.1, 44.8, and 46.0 S·cm−1, respectively.
- 1 December 2021
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 94, 230-238
Simple and rapid conversion of silicon carbide to nanodiamonds at ambient pressure
- 1 December 2021
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 94, 230-238
Simple and rapid conversion of silicon carbide to nanodiamonds at ambient pressure
- Open Access
Surface Optimization of ZrC–SiC Inner Layer to Enhance Ablation Property of SiC/ZrC–SiC Multi-Layer Coating for C/C Composites
A ZrC–SiC inner layer was fabricated on carbon/carbon composites by pack cementation at different temperatures, aiming to prepare a transition layer for subsequent deposition of SiC and ZrC–SiC layer by chemical vapor deposition and plasma spray. Results show that the structure and phase composition of the inner layer significantly affected the interface bonding strength and thermal shock resistance of the multilayer, which played a vital role in resisting ablation. The jagged and porous surface of the inner layer led to forming a root-like pinning interface, generating a sawtooth combination between the layers. Moreover, the inner layer with high SiC content decreased the coefficient of thermal expansion mismatch between the inner and outer layers. Therefore, the enhanced ablation resistance of the optimum coating was attributed to the improved interface bonding strength and thermal shock resistance caused by the ZrC–SiC inner layer with rough and porous surface structure.
Open AccessSurface Optimization of ZrC–SiC Inner Layer to Enhance Ablation Property of SiC/ZrC–SiC Multi-Layer Coating for C/C Composites
A ZrC–SiC inner layer was fabricated on carbon/carbon composites by pack cementation at different temperatures, aiming to prepare a transition layer for subsequent deposition of SiC and ZrC–SiC layer by chemical vapor deposition and plasma spray. Results show that the structure and phase composition of the inner layer significantly affected the interface bonding strength and thermal shock resistance of the multilayer, which played a vital role in resisting ablation. The jagged and porous surface of the inner layer led to forming a root-like pinning interface, generating a sawtooth combination between the layers. Moreover, the inner layer with high SiC content decreased the coefficient of thermal expansion mismatch between the inner and outer layers. Therefore, the enhanced ablation resistance of the optimum coating was attributed to the improved interface bonding strength and thermal shock resistance caused by the ZrC–SiC inner layer with rough and porous surface structure.
- Open Access
- 25 September 2020
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 8 (4) , 1162-1174
Effect of fiber-oriented direction on mechanical and ablative performance of C/C-HfC-ZrC-SiC composites
C/C-HfC-ZrC-SiC composites are fabricated by precursor infiltration and pyrolysis process by using SiC, ZrC, and HfC precursors. With incorporation of ZrC-SiC ceramics, the ablation rates of the C/C-HfC-ZrC-SiC composites are one order magnitude lower than that of C/C-HfC composites. Due to structural difference of the preform and the distributed UHTC particles in two directions, C/C-HfC-ZrC-SiC composites show superior mechanical and ablative properties in XY direction. Meanwhile, the linear and mass ablation rates of XY direction are lower than that of XZ direction. The inferior ablation resistance of XZ direction is mainly concerned with the preferentially ablated fiber ends in cross-section and the absence of needled fibers in the fiber layers. After 240 s ablation test, the linear and mass ablation rates of XY and XZ directions are 0.167 ± 0.02 μm/s, 0.007 ± 0.002 mg/s and 0.521 ± 0.04 μm/s, 0.050 ± 0.003 mg/s, respectively. The lowest ablation rates after 240 s ablation indicate that the C/C-HfC-ZrC-SiC composites have great potential for long-term ablation applications.
- 25 September 2020
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 8 (4) , 1162-1174
Open AccessEffect of fiber-oriented direction on mechanical and ablative performance of C/C-HfC-ZrC-SiC composites
C/C-HfC-ZrC-SiC composites are fabricated by precursor infiltration and pyrolysis process by using SiC, ZrC, and HfC precursors. With incorporation of ZrC-SiC ceramics, the ablation rates of the C/C-HfC-ZrC-SiC composites are one order magnitude lower than that of C/C-HfC composites. Due to structural difference of the preform and the distributed UHTC particles in two directions, C/C-HfC-ZrC-SiC composites show superior mechanical and ablative properties in XY direction. Meanwhile, the linear and mass ablation rates of XY direction are lower than that of XZ direction. The inferior ablation resistance of XZ direction is mainly concerned with the preferentially ablated fiber ends in cross-section and the absence of needled fibers in the fiber layers. After 240 s ablation test, the linear and mass ablation rates of XY and XZ directions are 0.167 ± 0.02 μm/s, 0.007 ± 0.002 mg/s and 0.521 ± 0.04 μm/s, 0.050 ± 0.003 mg/s, respectively. The lowest ablation rates after 240 s ablation indicate that the C/C-HfC-ZrC-SiC composites have great potential for long-term ablation applications.
- 20 November 2019
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (2)
Improved Thermal Conductivity and Ablation Resistance of Microdiamond‐Modified C/C Composites after Diamond Graphitization
C/C composites with diamond addition are prepared, and a 1600 °C heat treatment is conducted to investigate the effects of diamond graphitization on the ablation resistance and thermal conductivity of the composites. With diamond content increasing, a higher degree of stress graphitization occurs to the surrounding pyrolytic carbon (PyC) due to the enhanced stress accumulation in the diamond stacking region during graphitization process. After heat treatment at 1600 °C, the single diamond/PyC interface is substituted by complex diamond/graphite and graphite/PyC interfaces which results in a more compact structure and enhanced interface strength. Benefiting from the optimized interface microstructure and reduced closed pores after diamond graphitization, higher thermal conductivities are achieved for C/C–diamond composites. The ablation performance of the composites is improved due to the better oxidation resistance of diamond particles, increased compactness of diamond stacking region, and optimized thermal properties of the composites.
- 20 November 2019
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (2)
Improved Thermal Conductivity and Ablation Resistance of Microdiamond‐Modified C/C Composites after Diamond Graphitization
C/C composites with diamond addition are prepared, and a 1600 °C heat treatment is conducted to investigate the effects of diamond graphitization on the ablation resistance and thermal conductivity of the composites. With diamond content increasing, a higher degree of stress graphitization occurs to the surrounding pyrolytic carbon (PyC) due to the enhanced stress accumulation in the diamond stacking region during graphitization process. After heat treatment at 1600 °C, the single diamond/PyC interface is substituted by complex diamond/graphite and graphite/PyC interfaces which results in a more compact structure and enhanced interface strength. Benefiting from the optimized interface microstructure and reduced closed pores after diamond graphitization, higher thermal conductivities are achieved for C/C–diamond composites. The ablation performance of the composites is improved due to the better oxidation resistance of diamond particles, increased compactness of diamond stacking region, and optimized thermal properties of the composites.
- Open Access
- 30 July 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (47) , 26934-26937
(B,N)-Doped 3D porous graphene–CNTs synthesized by chemical vapor deposition as a bi-functional catalyst for ORR and HER
A simple but very efficient two-step CVD method to prepare a (B,N)-doped 3D porous graphene–CNT hybrid material (B–N–G–CNT), and its catalytic performance for ORR and HER.
- 30 July 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (47) , 26934-26937
Open Access(B,N)-Doped 3D porous graphene–CNTs synthesized by chemical vapor deposition as a bi-functional catalyst for ORR and HER
A simple but very efficient two-step CVD method to prepare a (B,N)-doped 3D porous graphene–CNT hybrid material (B–N–G–CNT), and its catalytic performance for ORR and HER.
- 10 February 2018
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 22 (7) , 1971-1981
Electrochemical characteristics and interfacial contact resistance of Ni-P/TiN/PTFE coatings on Ti bipolar plates
- 10 February 2018
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 22 (7) , 1971-1981
Electrochemical characteristics and interfacial contact resistance of Ni-P/TiN/PTFE coatings on Ti bipolar plates