Özkan Akin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Özkan Akin has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Erman Selim
Department of Electrical and Electronics Engineering, Ege University, Izmir, Türkiye
1 shared publication - Halil Ünlü
Ege University, Department of Electrical and Electronics Engineering, Izmir 35100, Turkey
1 shared publication - Irfan Alan
Department of Electrical and Electronics Engineering, Abdullah Gul University, Kayseri, Turkey
1 shared publication - İbRahim Özer
Ege University, Department of Electrical and Electronics Engineering, Izmir 35100, Turkey
1 shared publication Umit Tarhan
Haier GmbH Deutschland, Nrnberg, Deutschland
1 shared publication
Latest Publications
- 15 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Canadian Journal of Electrical and Computer Engineering
- Vol. 45 (2) , 105-113
Determination and Functional Implementation of Operating Point of a Centrifugal Pump With BLDC Motor
In the present study, a sensorless method is proposed to determine the operating point on pump curves in a BLDC-driven centrifugal pump, and certain functional implementations of the operating point are investigated. To develop a sensorless system, a calibration method is defined for the setup time. System variables such as head, flow, and power are determined at runtime based on the calibration data and the control algorithm of the BLDC motor. Thus, beneficial improvements are achieved for centrifugal pump systems, since only motor phase current sensors are required at runtime. These parameters are used to force the system into various modes such as ``minimum energy,'' ``maximum efficiency,'' or ``fastest,'' which could be selected by the user. The experimental results for an open-loop pump system setup as a part of the experiment are presented.
- 15 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Canadian Journal of Electrical and Computer Engineering
- Vol. 45 (2) , 105-113
Determination and Functional Implementation of Operating Point of a Centrifugal Pump With BLDC Motor
In the present study, a sensorless method is proposed to determine the operating point on pump curves in a BLDC-driven centrifugal pump, and certain functional implementations of the operating point are investigated. To develop a sensorless system, a calibration method is defined for the setup time. System variables such as head, flow, and power are determined at runtime based on the calibration data and the control algorithm of the BLDC motor. Thus, beneficial improvements are achieved for centrifugal pump systems, since only motor phase current sensors are required at runtime. These parameters are used to force the system into various modes such as ``minimum energy,'' ``maximum efficiency,'' or ``fastest,'' which could be selected by the user. The experimental results for an open-loop pump system setup as a part of the experiment are presented.
- Open Access
- 15 April 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (1) , 19-25
Selective harmonic elimination in multi-level inverters by using neural networks
In this study, it is aimed to eliminate the harmonics selected by the selective harmonic elimination (SHE) method in a 7-level cascade multilevel inverter using artificial neural networks (ANNs). A control algorithm has been developed in which the 3rd and 5th harmonics or 5th and 7th harmonics can be eliminated according to the selection while adjusting the output voltage amplitude of the inverter. The required switching angles for SHE are calculated in real time using ANN. These angles were first obtained offline training of ANN using Newton-Raphson method. ANN was trained in MATLAB® environment according to the obtained data. The resulting ANN algorithm and practical implementation using the STM32F429 ARM microcontroller® and inverter switching was provided. Experimental results of the system with RL load were tested.
- 15 April 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (1) , 19-25
Open AccessSelective harmonic elimination in multi-level inverters by using neural networks
In this study, it is aimed to eliminate the harmonics selected by the selective harmonic elimination (SHE) method in a 7-level cascade multilevel inverter using artificial neural networks (ANNs). A control algorithm has been developed in which the 3rd and 5th harmonics or 5th and 7th harmonics can be eliminated according to the selection while adjusting the output voltage amplitude of the inverter. The required switching angles for SHE are calculated in real time using ANN. These angles were first obtained offline training of ANN using Newton-Raphson method. ANN was trained in MATLAB® environment according to the obtained data. The resulting ANN algorithm and practical implementation using the STM32F429 ARM microcontroller® and inverter switching was provided. Experimental results of the system with RL load were tested.
- Open Access
- 1 January 2010
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 18 (6) , 943-962
The use of FPGA in field-oriented control of an induction machine
In this study, the feasibility of embedding the field oriented control (FOC) of an induction machine into field programmable gate arrays (FPGA) is investigated. An indirect FOC of an induction machine is simulated in a Matlab Simulink environment using a Xilinx System Generator implemented in a Xilinx Spartan-3 XC3S200 FPGA board. Design of the developed controller for the induction machine is simulated via a Simulink full digital platform. The resulting design has a flexible and modular structure where the designer can customize the hardware blocks by changing the number of inputs, outputs, and algorithm when it is compared to the designs implemented using classical microcontrollers and digital signal processors. With its flexibility, other control algorithms can easily be programmed and embedded into the FPGA. The controller developed can be imbedded and implemented on the Digilab S3 Spartan-3 XC3S200 FPGA development board produced by the Digilent Company. Performance of the developed system has been tested at different load torques and various induction machine speeds.
- 1 January 2010
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 18 (6) , 943-962
Open AccessThe use of FPGA in field-oriented control of an induction machine
In this study, the feasibility of embedding the field oriented control (FOC) of an induction machine into field programmable gate arrays (FPGA) is investigated. An indirect FOC of an induction machine is simulated in a Matlab Simulink environment using a Xilinx System Generator implemented in a Xilinx Spartan-3 XC3S200 FPGA board. Design of the developed controller for the induction machine is simulated via a Simulink full digital platform. The resulting design has a flexible and modular structure where the designer can customize the hardware blocks by changing the number of inputs, outputs, and algorithm when it is compared to the designs implemented using classical microcontrollers and digital signal processors. With its flexibility, other control algorithms can easily be programmed and embedded into the FPGA. The controller developed can be imbedded and implemented on the Digilab S3 Spartan-3 XC3S200 FPGA development board produced by the Digilent Company. Performance of the developed system has been tested at different load torques and various induction machine speeds.