Xiaoqing Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaoqing Chen has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Haoyi Li
College of Mechanical and Electrical Engineering Beijing University of Chemical Technology Beijing China
3 shared publications - Weimin Yang
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing, China
3 shared publications - Youchen Zhang
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
3 shared publications - Mingjun Chen
Department of Traditional Chinese Medicine and Acupuncture, The Second Medical Center & National Clinical Research Center for Geriatric Diseases, Chinese PLA General Hospital, Beijing 100853, China
2 shared publications - Xuetao He
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing, China
2 shared publications Abdul Latif
Department of Mechanical Engineering QUEST Nawabshah Nawabshah Pakistan
1 shared publication
Latest Publications
- 17 March 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (29) , 50710
Ionic liquids enhanced performance of PVC gels actuator
Stimulated devices are highly demanded for actuators and artificial muscles in the recent era but susceptible to low deformation at an applied voltage. In the present work, ionic liquids (ILs) based gel films were prepared from the polyvinyl chloride (PVC), dibutyl adipate (DBA), 1‐butyl, 3‐methimidazolium chloride, and 1‐pentyl‐3‐methylimidazolium hexafluorophosphate by a simple solvent evaporation method. The structural, morphological, optical, and mechanical properties of the composite PVC/ILs gel were characterized by Fourier‐transform infrared spectroscopy (FTIR), Large Angle X‐ray scattering (LAXS), UV–visible (UV–vis) absorption spectroscopy, scanning electron micrpscopy (SEM) and elemental mapping. We found that the displacement of plasticized PVC gels‐based actuator was 0.1 mm with the response time of 0.33 s at an induced voltage of 1000 V. The loading of 0.02% of IL (fluorides) with PVC gel showed maximum deformation of 0.16 mm with a relatively rapid response time of 0.2 s. These high deformation and response time values of IL fluoride‐based gels are dramatically higher than reported PVC gels. Likewise, the loading of IL fluorides in the PVC gel showed a high elongation value at the break of about 377%. This work suggests that the flexible gel based on IL fluorides and PVC could be a potential candidate for the fabrication of high‐performance artificial muscles and tunable soft actuators.
- 17 March 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (29) , 50710
Ionic liquids enhanced performance of PVC gels actuator
Stimulated devices are highly demanded for actuators and artificial muscles in the recent era but susceptible to low deformation at an applied voltage. In the present work, ionic liquids (ILs) based gel films were prepared from the polyvinyl chloride (PVC), dibutyl adipate (DBA), 1‐butyl, 3‐methimidazolium chloride, and 1‐pentyl‐3‐methylimidazolium hexafluorophosphate by a simple solvent evaporation method. The structural, morphological, optical, and mechanical properties of the composite PVC/ILs gel were characterized by Fourier‐transform infrared spectroscopy (FTIR), Large Angle X‐ray scattering (LAXS), UV–visible (UV–vis) absorption spectroscopy, scanning electron micrpscopy (SEM) and elemental mapping. We found that the displacement of plasticized PVC gels‐based actuator was 0.1 mm with the response time of 0.33 s at an induced voltage of 1000 V. The loading of 0.02% of IL (fluorides) with PVC gel showed maximum deformation of 0.16 mm with a relatively rapid response time of 0.2 s. These high deformation and response time values of IL fluoride‐based gels are dramatically higher than reported PVC gels. Likewise, the loading of IL fluorides in the PVC gel showed a high elongation value at the break of about 377%. This work suggests that the flexible gel based on IL fluorides and PVC could be a potential candidate for the fabrication of high‐performance artificial muscles and tunable soft actuators.
- 16 February 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (15) , 9518-9531
String electrospinning based on the standing wave vibration
- 16 February 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (15) , 9518-9531
String electrospinning based on the standing wave vibration
- 7 January 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (31) , 48922
Polymer melt differential electrospinning from a linear slot spinneret
Preparation of melt electrospun fibers with high efficiency and high productivity remains a big challenge. A polymer melt differential electrospinning system with linear slot spinneret (LSSP) was proposed in this work. Under a high electric field, multiple jets distributed at the tip of LSSP were self‐organized from the polymer melt film with controlled thickness. The spinning parameters were investigated, and the electric filed between spinneret and collector was analyzed. The results showed that the interjet distance decreased significantly with the decrease of the thickness of polymer melt film and the Tayler cone size. The smallest average interjet distance of 1.9 mm with deviation of 0.5 mm was obtained under the condition of applied voltage of 45 kV, collecting distance of 9 cm, temperature of 250 °C, and slot thickness of 0.2 mm. The high output of 75.6 g/h was achieved and could be increased just by increasing the slot width. It was demonstrated that the proposed technology was a promising way to fabricate melt electrospun fibers with high efficiency. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48922.
- 7 January 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (31) , 48922
Polymer melt differential electrospinning from a linear slot spinneret
Preparation of melt electrospun fibers with high efficiency and high productivity remains a big challenge. A polymer melt differential electrospinning system with linear slot spinneret (LSSP) was proposed in this work. Under a high electric field, multiple jets distributed at the tip of LSSP were self‐organized from the polymer melt film with controlled thickness. The spinning parameters were investigated, and the electric filed between spinneret and collector was analyzed. The results showed that the interjet distance decreased significantly with the decrease of the thickness of polymer melt film and the Tayler cone size. The smallest average interjet distance of 1.9 mm with deviation of 0.5 mm was obtained under the condition of applied voltage of 45 kV, collecting distance of 9 cm, temperature of 250 °C, and slot thickness of 0.2 mm. The high output of 75.6 g/h was achieved and could be increased just by increasing the slot width. It was demonstrated that the proposed technology was a promising way to fabricate melt electrospun fibers with high efficiency. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48922.
- 11 September 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (1) , 901-910
Electrospinning on a plucked string
- 11 September 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (1) , 901-910
Electrospinning on a plucked string