DSDondeti Venkata Sivareddy

Dondeti Venkata Sivareddy

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Dondeti Venkata Sivareddy has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effect of thermo-mechanical loading on machining induced residual stresses in ultrasonic vibration assisted turning of Ti6Al4V alloy

    by Dondeti Venkata Sivareddy, Pasam Vamsi Krishna, Anne Venu Gopal

    The study of residual stresses induced during machining is of considerable importance due to their effect on fatigue life of machined components. The metallurgical changes occurred due to thermo-mechanical phenomenon in cutting process affects the distribution of residual stress in machined components. Ultrasonic vibration assisted turning (UVAT) is effective machining process for low thermal conductivity materials like Ti6Al4V alloy and improves the surface characteristics by reducing cutting force and cutting temperature. In this paper, experimental and finite element (FE) studies are conducted to study the circumferential and axial residual stress distribution in UVAT of Ti6Al4V alloy. FE model is developed to study the effect of vibrating parameter (ultrasonic power intensity) and cutting parameters (cutting speed, feed rate, and depth of cut) on the residual stress profiles of machined surface. The FE simulation results of cutting force and cutting temperature are validated with experimental results. The circumferential and axial surface residual stresses obtained from FE simulation are also compared with experimental results using X-ray diffraction method. The effect of thermo-mechanical loading on residual stress distribution is analyzed with respect to force components (cutting force and feed force) and cutting temperature. Finally, the effect of each cutting parameter on subsurface layer of machined component is analyzed.


  • Experimental Investigation on Flank Wear of the Tool in Ultrasonic Vibration-Assisted Turning of Ti6Al4V Alloy

    by D. Venkata Sivareddy, P. Vamsi Krishna, A. Venu Gopal

    High cutting temperatures developed during machining of Ti6Al4V alloy diminish the tool life by rapid increase in rate of tool wear. The high cutting temperatures increase the chemical reactivity of the workpiece with tool material and form the localized temperature zones at the vicinity of cutting tool edge. Ultrasonic vibration-assisted turning (UVAT) is an effective cutting technique in which tangential vibrations are provided to the cutting tool. The reduced cutting force and temperature improve the tool life in the UVAT process. In the present study, flank wear of the uncoated carbide cutting tool has been studied in UVAT processes at various cutting speeds (90, 120, and 150 m/min) and ultrasonic powers (80, 90, and 100 %). The flank wear of the tool is measured with a scanning electron microscope, and it is observed that tool wear is low in UVAT compared with the conventional turning (CT) process. Fracture of the cutting edge of the tool is observed in CT because of high compressive stresses with the high cutting temperature, which did not occur in the UVAT process. The growth of average and maximum flank wear with cutting velocity is low in UVAT, whereas rapid growth is observed in the CT process. From the experimental results, tool life improvement is observed in UVAT compared with CT at an average flank wear of 300 µm; however, this improvement is decreased with an increase in cutting speed in the order of 62, 53.2, and 32 % for 90, 120, and 150 m/min, respectively, at 100 % ultrasonic power. Similarly, tool life is improved with an increase in ultrasonic power in the order of 18, 55, and 62 % for 80, 90, and 100 % ultrasonic power, respectively, at 90 m/min cutting speed.


  • Tool-Work Contact Ratio and Parametric Influence in Ultrasonic Vibration–Assisted Turning of Ti6Al4V Alloy

    by D. Venkata Sivareddy, P. Vamsi Krishna, A. Venu Gopal

    The performance of the machining process depends on the time of contact of the cutting tool with the workpiece. In this work, the effect of vibrating and cutting parameters on tool-work contact ratio (TWCR) in ultrasonic vibration–assisted turning (UVAT) is evaluated. Machining performance is measured in terms of average cutting force, cutting temperature, and average surface roughness. Full factorial experiments are conducted on a Ti6Al4V alloy to evaluate the performance of the UVAT process in terms of TWCR. The performance of the UVAT process is analyzed and compared with the conventional turning process at various conditions, such as intensity of ultrasonic power (80, 90, and 100 %), cutting speed (10, 30, and 50 m/min), feed rate (0.055, 0.103, and 0.161 mm/rev), and depth of cut (0.1, 0.3, and 0.5 mm). The cutting force, cutting temperature, and surface roughness are decreased with the increase in percentage intensity of ultrasonic power. The effectiveness of UVAT process is greater at higher levels of vibrating parameters and lower levels of cutting parameters in the selected range. Finally, it is concluded that the maximum benefit from the UVAT process is obtained at TWCR of 0.136 and its effect is dominant at lower levels of cutting conditions. However, the effect of thermal loading is dominant at higher levels of cutting conditions in the selected range.


  • Determination of Constitutive Material Model Constants for Ti6Al4V Alloy at Near Orthogonal Machining Conditions

    by D. Venkata Sivareddy, P. Vamsi Krishna, A. Venu Gopal

    The accuracy of numerical modeling of a machining process largely depends on material model constants. The Johnson-Cook (J-C) material model constants, i.e., A, B, C, n, and m, describe deformation behavior of material under thermomechanical loading. This paper considers an equivalent strain hardening exponent neq in place of ‘n’ in the J-C constitutive law for accurate prediction of material model constants at near orthogonal machining conditions. The effect of strain on the secondary deformation zone, i.e., the tool-chip interface, is also considered for accurate prediction of material parameters. In the present work, a machining approach based on response surface methodology and particle swarm optimization technique are used to identify J-C material model constants for the Ti6Al4V alloy. The cutting force, feed force, and chip thickness obtained from orthogonal experiments are used to evaluate the physical quantities of Oxley’s extension theory at different rake angles. It is noted that J-C constants determined from the present approach at a 7° rake angle are more accurate in predicting flow stress than J-C constants determined from other methods. J-C constants identified from a machining approach show less deviation from the measured equivalent flow stresses obtained at similar machining conditions.


  • Open Access

    Parameter Optimisation in Vibration Assisted Turning of Ti6Al4V Alloy using ANOVA and Grey Relational Analysis

    by D. Venkata Sivareddy, P. Vamsi Krishna, A. Venu Gopal, C. L. Prithvi Raz

    The machining of Ti6Al4V alloy with vibration assisted turning (VAT) is an effective consideration to control the surface integrity of machined components. The effect of cutting and vibrating parameters in a VAT on cutting force, cutting temperature, equivalent stress and compressive maximum circumferential residual stress (MCRS) was studied in the present work. The parameter optimisation of a VAT of Ti6Al4V alloy was achieved with Taguchi based analysis of variance (ANOVA) and grey relational analysis (GRA). The input parameters considered for optimisation of VAT process are cutting speed, feed rate, frequency and amplitude. The finite element (FE) simulations were performed with commercial FE code, ABAQUS. The result shows that the vibrating parameters (frequency and amplitude) play a significant role than cutting parameters (speed and feed rate) in VAT process. The optimum condition for each output response was determined from ANOVA. The optimum condition obtained at 30 m/min of cutting speed, 150 μm of amplitude, 600 Hz of frequency and 0.05 mm/rev of feed rate for cutting force, cutting temperature and MCRS (compressive) while the optimum condition for equivalent stress is 30 m/min of cutting speed, 100 μm of amplitude, 600 Hz of frequency and 0.05 mm/rev of feed rate. The GRA suggests the combination of process parameters 30 m/min of cutting speed, 150 μm of amplitude, 600 Hz of frequency and 0.05 mm/rev of feed rate provides the optimum response.