Assanali T. Sultanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Assanali T. Sultanov has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Nurzhan B. Beisenkhanov
School of Materials Science and Green Technologies, Kazakh-British Technical University, Tole bi 59, Almaty 050000, Kazakhstan
9 shared publications - A. Zh. Kusainova
Kazakhstan-British Technical University
6 shared publications - Ilya Zhirkov
Kazakh-British Technical University
6 shared publications - K. Kh. Nussupov
Kazakh-British Technical University
6 shared publications Kair Nussupov
3 shared publications- A. Ph. Eshanov
Kazakh-British Technical University
2 shared publications
Latest Publications
- Open Access
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 486-497
ANALYZING THE EFFECTS OF SPIN-COATED PHOSPHOSILICATE GLASS ON THE CRYSTALLIZATION PROCESS OF SILICON THIN FILMS DEPOSITED VIA MAGNETRON SPUTTERING
This study investigates the influence of spin-coated phosphosilicate glass (PSG) on the crystallization and electrical properties of silicon (Si) thin films deposited by magnetron sputtering, with a focus on optimizing their structural and electrical properties for potential applications in photovoltaics and microelectronics. The results demonstrate that higher spin-coating speeds lead to thinner and more uniform PSG layers, which in turn promote more efficient phosphorus diffusion and enhance film crystallization. Annealing at 950 °C resulted in enhanced dopant activation, improved crystallinity, and reduced sheet resistance. These structural and phase transformations were systematically analyzed by X-ray diffraction (XRD), providing detailed insight into the evolution of the Si thin films during thermal processing. In particular, the XRD results reveal a clear transition from the amorphous to the polycrystalline state, especially for samples processed at optimized spin speeds and elevated annealing temperatures. Optical characterization further showed that thermal annealing modified the reflectance and transmittance spectra and slightly increased the refractive index and extinction coefficient of the sputtered Si films. Overall, the combination of environmentally friendly spin-on doping with scalable physical deposition techniques represents a promising approach for the development of advanced photovoltaic technologies, offering a viable pathway toward sustainable and efficient device fabrication.
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 486-497
Open AccessANALYZING THE EFFECTS OF SPIN-COATED PHOSPHOSILICATE GLASS ON THE CRYSTALLIZATION PROCESS OF SILICON THIN FILMS DEPOSITED VIA MAGNETRON SPUTTERING
This study investigates the influence of spin-coated phosphosilicate glass (PSG) on the crystallization and electrical properties of silicon (Si) thin films deposited by magnetron sputtering, with a focus on optimizing their structural and electrical properties for potential applications in photovoltaics and microelectronics. The results demonstrate that higher spin-coating speeds lead to thinner and more uniform PSG layers, which in turn promote more efficient phosphorus diffusion and enhance film crystallization. Annealing at 950 °C resulted in enhanced dopant activation, improved crystallinity, and reduced sheet resistance. These structural and phase transformations were systematically analyzed by X-ray diffraction (XRD), providing detailed insight into the evolution of the Si thin films during thermal processing. In particular, the XRD results reveal a clear transition from the amorphous to the polycrystalline state, especially for samples processed at optimized spin speeds and elevated annealing temperatures. Optical characterization further showed that thermal annealing modified the reflectance and transmittance spectra and slightly increased the refractive index and extinction coefficient of the sputtered Si films. Overall, the combination of environmentally friendly spin-on doping with scalable physical deposition techniques represents a promising approach for the development of advanced photovoltaic technologies, offering a viable pathway toward sustainable and efficient device fabrication.
- 12 May 2026
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 212
Proximity rapid thermal diffusion for simultaneous phosphorus and boron doping of silicon
- 12 May 2026
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 212
Proximity rapid thermal diffusion for simultaneous phosphorus and boron doping of silicon
- Open Access
- 20 December 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 93-105
Computer simulation of planar bifacial TOPCon solar cells by using Quokka 3 software
This study presents a comprehensive simulation-based analysis of bifacial Tunnel Oxide Passivated Contact (TOPCon) solar cells using the Quokka 3 software. It investigates the impact of different antireflection coatings and rear albedo variations on device performance. One of the main findings is the significant improvement in optical and electrical properties after applying MgF2 antireflection coating on top of the cell. Structures with the addition of MgF2 achieved low, uniform reflectance and increased light absorption across the full solar spectrum. Compared to structures without MgF2, those with the coating exhibited superior external quantum efficiency (EQE) and reduced reflected photocurrent density (JR) with the value of 3.38 mA/cm2. Additionally, simulations revealed that increasing rear albedo values improved short-circuit current density (Jsc) and power conversion efficiency (PCE). The highest PCE of 27.37% and Jsc of 45.07 mA/cm2 was obtained from a structure combining MgF2 and a rear albedo of 0.3 Voc in this case was equal to 0.74V. These results confirm that optimizing both antireflection coatings and rear-side illumination can significantly improve the efficiency of bifacial TOPCon solar cells, offering a viable pathway for enhanced photovoltaic (PV) performance.
- 20 December 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 93-105
Open AccessComputer simulation of planar bifacial TOPCon solar cells by using Quokka 3 software
This study presents a comprehensive simulation-based analysis of bifacial Tunnel Oxide Passivated Contact (TOPCon) solar cells using the Quokka 3 software. It investigates the impact of different antireflection coatings and rear albedo variations on device performance. One of the main findings is the significant improvement in optical and electrical properties after applying MgF2 antireflection coating on top of the cell. Structures with the addition of MgF2 achieved low, uniform reflectance and increased light absorption across the full solar spectrum. Compared to structures without MgF2, those with the coating exhibited superior external quantum efficiency (EQE) and reduced reflected photocurrent density (JR) with the value of 3.38 mA/cm2. Additionally, simulations revealed that increasing rear albedo values improved short-circuit current density (Jsc) and power conversion efficiency (PCE). The highest PCE of 27.37% and Jsc of 45.07 mA/cm2 was obtained from a structure combining MgF2 and a rear albedo of 0.3 Voc in this case was equal to 0.74V. These results confirm that optimizing both antireflection coatings and rear-side illumination can significantly improve the efficiency of bifacial TOPCon solar cells, offering a viable pathway for enhanced photovoltaic (PV) performance.
- Open Access
- 29 January 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (5)
Laminated Carbon Based Flexible Printed Perovskite Solar Cells Passivated with Tin(II) Phthalocyanine
Production scalability, efficiency, and stability challenges continue to impede the commercial viability of perovskite solar cells (PSCs). In this study, a multifunctional passivation technique is introduced, designed to enhance the efficiency and stability of printable, air‐processed PSCs with laminated carbon electrodes. This findings indicate that tin(II) phthalocyanine (SnPC) molecules act as an interfacial layer between the absorber and the hole‐transporting layer (HTL), effectively passivating surface trap states and facilitating hole extraction. Optimal SnPC surface treatment reduces the trap density in the perovskite layer from 2.1 × 1015 to 1.5 × 1015 cm−3, increases carrier mobility (from 2.7 × 10−3 to 2.8 × 10−3 cm2 Vs−1), and extends carrier lifetime. SEM, AFM, EDS, and XPS analyses confirm the presence of SnPC on the perovskite layer surface and its influence on surface morphology. Devices treated with an optimal SnPC concentration exhibit significant efficiency improvements, from 6.4% to 8.5%, along with a threefold increase in photo‐stability. Thus, SnPC may serve as a passivating buffer layer for the perovskite surface, offering protection against photo‐degradation.
- 29 January 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (5)
Open AccessLaminated Carbon Based Flexible Printed Perovskite Solar Cells Passivated with Tin(II) Phthalocyanine
Production scalability, efficiency, and stability challenges continue to impede the commercial viability of perovskite solar cells (PSCs). In this study, a multifunctional passivation technique is introduced, designed to enhance the efficiency and stability of printable, air‐processed PSCs with laminated carbon electrodes. This findings indicate that tin(II) phthalocyanine (SnPC) molecules act as an interfacial layer between the absorber and the hole‐transporting layer (HTL), effectively passivating surface trap states and facilitating hole extraction. Optimal SnPC surface treatment reduces the trap density in the perovskite layer from 2.1 × 1015 to 1.5 × 1015 cm−3, increases carrier mobility (from 2.7 × 10−3 to 2.8 × 10−3 cm2 Vs−1), and extends carrier lifetime. SEM, AFM, EDS, and XPS analyses confirm the presence of SnPC on the perovskite layer surface and its influence on surface morphology. Devices treated with an optimal SnPC concentration exhibit significant efficiency improvements, from 6.4% to 8.5%, along with a threefold increase in photo‐stability. Thus, SnPC may serve as a passivating buffer layer for the perovskite surface, offering protection against photo‐degradation.
- Open Access
- 3 October 2024
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 21 (3) , 302-313
INFLUENCE OF THE RATIO OF GASE CONSUMPTION N2/Ar AND MAGNETRON POWER ON THE DENSITY AND STOICHIOMETRIC COMPOSITION OF TINX FILMS SYNTHESIZED BY MAGNETRON SPUTTERING METHOD
The films of titanium nitride were deposited by direct current magnetron sputtering on the surface of singlecrystalline silicon samples in an Ar-N2 atmosphere for use as a diffusion barrier. The thickness and density of films were measured by X-ray reflectometry. The design of the MAGNA TM-200-01 installation has been changed to increase the supply of nitrogen into the chamber. The influences of sputtering conditions, including the flow rate of nitrogen and argon gases and their N2 /Ar ratios in the range of 1–60 in the chamber, magnetron power of 690–1400 W on the formation of TiNx films, their density and stoichiometric composition, were studied. It is shown that the value of x is affected not only by the N2 /Ar gas flow rate ratio, but also by the magnetron power. At the sputtering parameters 1200 W, N2 /Ar = 30, 0.8 Pa, 320 s and 100°C, a maximum density of 5.247 g/cm3 of a film was achieved, which corresponds to the composition TiN0.786 = Ti56N44. The presence of nanocrystalline film of titanium nitride and the absence of a nanocrystalline titanium phase were confirmed by photographic X-ray diffraction. It was found that for the synthesis of titanium nitride as close as possible to the stoichiometric composition TiN0.770 - TiN0.786, it is necessary to use magnetron power in the range of 900–1200 W, nitrogen rate of 30 cm3 /min with low argon flows of 1–5 cm3 /min.
- 3 October 2024
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 21 (3) , 302-313
Open AccessINFLUENCE OF THE RATIO OF GASE CONSUMPTION N2/Ar AND MAGNETRON POWER ON THE DENSITY AND STOICHIOMETRIC COMPOSITION OF TINX FILMS SYNTHESIZED BY MAGNETRON SPUTTERING METHOD
The films of titanium nitride were deposited by direct current magnetron sputtering on the surface of singlecrystalline silicon samples in an Ar-N2 atmosphere for use as a diffusion barrier. The thickness and density of films were measured by X-ray reflectometry. The design of the MAGNA TM-200-01 installation has been changed to increase the supply of nitrogen into the chamber. The influences of sputtering conditions, including the flow rate of nitrogen and argon gases and their N2 /Ar ratios in the range of 1–60 in the chamber, magnetron power of 690–1400 W on the formation of TiNx films, their density and stoichiometric composition, were studied. It is shown that the value of x is affected not only by the N2 /Ar gas flow rate ratio, but also by the magnetron power. At the sputtering parameters 1200 W, N2 /Ar = 30, 0.8 Pa, 320 s and 100°C, a maximum density of 5.247 g/cm3 of a film was achieved, which corresponds to the composition TiN0.786 = Ti56N44. The presence of nanocrystalline film of titanium nitride and the absence of a nanocrystalline titanium phase were confirmed by photographic X-ray diffraction. It was found that for the synthesis of titanium nitride as close as possible to the stoichiometric composition TiN0.770 - TiN0.786, it is necessary to use magnetron power in the range of 900–1200 W, nitrogen rate of 30 cm3 /min with low argon flows of 1–5 cm3 /min.
- 19 July 2024
- Published by Elsevier in Optical Materials
- Vol. 155
Investigation on optical and electrical properties of multilayer ITO/AZO/ITO transparent conductive oxides
- 19 July 2024
- Published by Elsevier in Optical Materials
- Vol. 155
Investigation on optical and electrical properties of multilayer ITO/AZO/ITO transparent conductive oxides
- Open Access
- 12 December 2023
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 20 (4) , 109-117
Effect of oxygen flow on electrical and optical properties of ITO films synthesized by magnetron sputtering method
The tin-doped indium oxide thin films were synthesized by DC magnetron sputtering on the surface of polished silicon samples and glass slides in a mixed argon-oxygen atmosphere. The other deposition parameters: operating pressure, magnetron power and substrate rotation speed were kept constant. Thickness and density of thin films were measured by X-ray Reflectometry. The effects of oxygen flow rate and substrate temperature on the optical and electrical properties were investigated. The electrical properties (resistivity, Hall mobility and charge concentration) of the thin films were measured by the Van der Pauw method using the Hall effect. The minimum value of resistivity 0.52 × 10-3 Ohm·cm, and maximum charge mobility 28 cm2V-1s-1 was achieved at an oxygen proportional gas mixture of 2.6% (0.71 sccm). The transmission spectra of the films were measured in the wavelength range from 300 to 1100 nm. The transmittance of all films exceeds 75% in the visible and near-infrared spectral ranges. It was found that increasing the oxygen flow rate and heating of the substrate up to optimal value 150°C led to an increase in the crystallinity of the films and, consequently, to an increase in the Hall mobility and the transmittance.
- 12 December 2023
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 20 (4) , 109-117
Open AccessEffect of oxygen flow on electrical and optical properties of ITO films synthesized by magnetron sputtering method
The tin-doped indium oxide thin films were synthesized by DC magnetron sputtering on the surface of polished silicon samples and glass slides in a mixed argon-oxygen atmosphere. The other deposition parameters: operating pressure, magnetron power and substrate rotation speed were kept constant. Thickness and density of thin films were measured by X-ray Reflectometry. The effects of oxygen flow rate and substrate temperature on the optical and electrical properties were investigated. The electrical properties (resistivity, Hall mobility and charge concentration) of the thin films were measured by the Van der Pauw method using the Hall effect. The minimum value of resistivity 0.52 × 10-3 Ohm·cm, and maximum charge mobility 28 cm2V-1s-1 was achieved at an oxygen proportional gas mixture of 2.6% (0.71 sccm). The transmission spectra of the films were measured in the wavelength range from 300 to 1100 nm. The transmittance of all films exceeds 75% in the visible and near-infrared spectral ranges. It was found that increasing the oxygen flow rate and heating of the substrate up to optimal value 150°C led to an increase in the crystallinity of the films and, consequently, to an increase in the Hall mobility and the transmittance.
- Open Access
- 27 October 2023
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 10 (3-4) , 28-32
Influence of the RF magnetron sputtering power on the optical and electrical properties of AZO films
Thin AZO films were synthesized using radio frequency magnetron sputtering method on the surface of polished silicon samples and glass slides. The sputtering power was varied in the range of 150–300 W with the step of 25W; deposition time was adjusted so that the film thickness remained equal to 70 nm. The rest of the deposition parameters: working pressure, temperature, and the substrate rotation rate, remained unchanged. The thickness and deposition rate of thin films were measured using X-ray reflectometry. The electrical properties (resistivity, Hall mobility and charge concentration) of thin films were measured by the Van Der Pauw method using the Hall effect. The transmission spectra of the films were measured in the wavelength range from 300 to 1100 nm. The average crystallite size was determined using X-ray diffraction spectra and the Scherrer equation. As a result, it was shown that AZO films synthesized at a power of 300 W have the best electrical and optical properties. At this power, the lowest resistivity value of 2.83×10-3 Ω∙cm and the maximum charge mobility of 9.6 cm2V-1sec-1 were achieved for films of the same thickness 70 nm. The decrease in the electrical resistivity of the films with increasing power is explained by more intense heating of the substrate during deposition, which leads to an improvement in the crystallinity of the film, and, as a consequence, to an increase in the mobility of charge carriers.
- 27 October 2023
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 10 (3-4) , 28-32
Open AccessInfluence of the RF magnetron sputtering power on the optical and electrical properties of AZO films
Thin AZO films were synthesized using radio frequency magnetron sputtering method on the surface of polished silicon samples and glass slides. The sputtering power was varied in the range of 150–300 W with the step of 25W; deposition time was adjusted so that the film thickness remained equal to 70 nm. The rest of the deposition parameters: working pressure, temperature, and the substrate rotation rate, remained unchanged. The thickness and deposition rate of thin films were measured using X-ray reflectometry. The electrical properties (resistivity, Hall mobility and charge concentration) of thin films were measured by the Van Der Pauw method using the Hall effect. The transmission spectra of the films were measured in the wavelength range from 300 to 1100 nm. The average crystallite size was determined using X-ray diffraction spectra and the Scherrer equation. As a result, it was shown that AZO films synthesized at a power of 300 W have the best electrical and optical properties. At this power, the lowest resistivity value of 2.83×10-3 Ω∙cm and the maximum charge mobility of 9.6 cm2V-1sec-1 were achieved for films of the same thickness 70 nm. The decrease in the electrical resistivity of the films with increasing power is explained by more intense heating of the substrate during deposition, which leads to an improvement in the crystallinity of the film, and, as a consequence, to an increase in the mobility of charge carriers.