Zhao Li
Zhao Li has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Run Wu
Wuhan University of Science and Technology
2 shared publications - Duo Zuo
College of Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China
1 shared publication - Guifeng Zhou
College of Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, China
1 shared publication - Jianhua Zhou
Central Research Institue (Qingshan), Baosteel Cooperation, Wuhan 430081, China
1 shared publication - Junjie Fei
Wuhan Vocational College of Software and Engineering (Wuhan Open University), Wuhan 430205, China
1 shared publication - Mingwei Li
Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081, China
1 shared publication
Latest Publications
- Open Access
- 10 April 2025
- Published by IOS Press
- p. 612-620
Breaking a Fixed Cognition in Traditional Chemistry Teaching – Taking the Influence of Constraints on Reversible Reactions on the Volume Fraction of Products as the Example
For the sake of explaining the doubts from teachers and students about whether the maximum volume fraction of the product can be obtained when the feed ratio of reactants is stoichiometric ratio in reversible reactions, the influence of the feed ratio of reactants on the volume fraction of the products under different constraint conditions were analyzed through mathematical deduction in this paper. The results show that the largest volume fractions of products can be obtained when the reactants are fed according to the stoichiometric ratio under the condition of constant concentration and amount of substance concentration of reactants. However, no optimal feed ratio of reactants can be obtained for reactions with changes in the amount of gaseous substance or in constraint conditions. Not only the results correct the inherent cognition of chemical reaction, but it also helps students understand the mechanism and laws of chemical reactions.
- 10 April 2025
- Published by IOS Press
- p. 612-620
Open AccessBreaking a Fixed Cognition in Traditional Chemistry Teaching – Taking the Influence of Constraints on Reversible Reactions on the Volume Fraction of Products as the Example
For the sake of explaining the doubts from teachers and students about whether the maximum volume fraction of the product can be obtained when the feed ratio of reactants is stoichiometric ratio in reversible reactions, the influence of the feed ratio of reactants on the volume fraction of the products under different constraint conditions were analyzed through mathematical deduction in this paper. The results show that the largest volume fractions of products can be obtained when the reactants are fed according to the stoichiometric ratio under the condition of constant concentration and amount of substance concentration of reactants. However, no optimal feed ratio of reactants can be obtained for reactions with changes in the amount of gaseous substance or in constraint conditions. Not only the results correct the inherent cognition of chemical reaction, but it also helps students understand the mechanism and laws of chemical reactions.
- Open Access
Research on the Effect of Pearlite Lamellar Spacing on Rolling Contact Wear Behavior of U75V Rail Steel
The damage mode of U75V rail steel in application is determined by its rolling wear behavior. In this paper, the pearlite microstructure of U75V steel is characterized to investigate the relationship between wear and fatigue behavior. The results show that, with decreasing of pearlite lamellar spacing, the wear resistance of the steel increases and the contact fatigue resistance decreases. The spacing decreasing causes the change of the wear mechanism from abrasive wear to adhesive wear, as well as the damage mode from wear damage to fatigue damage. The smaller the pearlite lamellar spacing is, the stronger the deformation of the cementite lamellar is. The thin cementite lamellar is hardly broken in the rolling friction to pile up a large number of dislocations in the ferrite matrix and the work hardening degree was improved. So, the plastic deformation layer is difficult to remove, and fatigue cracks are easy to initiate and extend to the interior of the material.
Open AccessResearch on the Effect of Pearlite Lamellar Spacing on Rolling Contact Wear Behavior of U75V Rail Steel
The damage mode of U75V rail steel in application is determined by its rolling wear behavior. In this paper, the pearlite microstructure of U75V steel is characterized to investigate the relationship between wear and fatigue behavior. The results show that, with decreasing of pearlite lamellar spacing, the wear resistance of the steel increases and the contact fatigue resistance decreases. The spacing decreasing causes the change of the wear mechanism from abrasive wear to adhesive wear, as well as the damage mode from wear damage to fatigue damage. The smaller the pearlite lamellar spacing is, the stronger the deformation of the cementite lamellar is. The thin cementite lamellar is hardly broken in the rolling friction to pile up a large number of dislocations in the ferrite matrix and the work hardening degree was improved. So, the plastic deformation layer is difficult to remove, and fatigue cracks are easy to initiate and extend to the interior of the material.
- Open Access
- 29 April 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 4748-4761
Influence of changes in alloying elements distribution and retained Austenite (RA) on mechanical properties of high boron alloy during quenching and partitioning(Q&P) process
- 29 April 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 4748-4761
Open AccessInfluence of changes in alloying elements distribution and retained Austenite (RA) on mechanical properties of high boron alloy during quenching and partitioning(Q&P) process
- Open Access
The Effect of Quenching and Partitioning (Q&P) Heat Treatment on the Microstructure and Mechanical Properties of High Boron Steel
High boron steel is prone to brittle failure due to the boride distributed in it with net-like or fishbone morphology, which limit its applications. The Quenching and Partitioning (Q&P) heat treatment is a promising process to produce martensitic steel with excellent mechanical properties, especially high toughness by increasing the volume fraction of retained austensite (RA) in the martensitic matrix. In this work, the Q&P heat treatment is used to improve the inherent defect of insufficient toughness of high boron steel, and the effect mechanism of this process on microstructure transformation and the change of mechanical properties of the steel has also been investigated. The high boron steel as-casted is composed of martensite, retained austensite (RA) and eutectic borides. A proper quenching and partitioning heat treatment leads to a significant change of the microstructure and mechanical properties of the steel. The net-like and fishbone-like boride is partially broken and spheroidized. The volume fraction of RA increases from 10% in the as-cast condition to 19%, and its morphology also changes from blocky to film-like. Although the macro-hardness has slightly reduced, the toughness is significantly increased up to 7.5 J·cm−2, and the wear resistance is also improved.
Open AccessThe Effect of Quenching and Partitioning (Q&P) Heat Treatment on the Microstructure and Mechanical Properties of High Boron Steel
High boron steel is prone to brittle failure due to the boride distributed in it with net-like or fishbone morphology, which limit its applications. The Quenching and Partitioning (Q&P) heat treatment is a promising process to produce martensitic steel with excellent mechanical properties, especially high toughness by increasing the volume fraction of retained austensite (RA) in the martensitic matrix. In this work, the Q&P heat treatment is used to improve the inherent defect of insufficient toughness of high boron steel, and the effect mechanism of this process on microstructure transformation and the change of mechanical properties of the steel has also been investigated. The high boron steel as-casted is composed of martensite, retained austensite (RA) and eutectic borides. A proper quenching and partitioning heat treatment leads to a significant change of the microstructure and mechanical properties of the steel. The net-like and fishbone-like boride is partially broken and spheroidized. The volume fraction of RA increases from 10% in the as-cast condition to 19%, and its morphology also changes from blocky to film-like. Although the macro-hardness has slightly reduced, the toughness is significantly increased up to 7.5 J·cm−2, and the wear resistance is also improved.