Mustafa Babagiray
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mustafa Babagiray has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Hamit Solmaz
Gazi University, Faculty of Technology, Automotive Engineering Department
3 shared publications Seyed Mohammad Safieddin Ardebili
3 shared publications- Tolga Kocakulak
Burdur Mehmet Akif Ersoy Üniversitesi
3 shared publications - Alper Calam
Gazi University, High Vocational School of Technical Sciences, Machinery and Material Technologies Dep
2 shared publications - Faruk Emre Aysal
Department of Mechanical Engineering, Faculty of Engineering, Giresun University, 28200 Giresun, Türkiye
2 shared publications - Fatih Aksoy
Afyon Kocatepe Universitesi
2 shared publications
Latest Publications
- Open Access
- 25 February 2025
- Published by EDP Sciences in Science and Technology for Energy Transition
- Vol. 80, 26
Impact of carbon quantum dot nanoparticles on combustion, performance and emissions in diesel/microwave-assisted canola oil biodiesel blend
Usage of biodiesel produced with conventional transesterification methods decreases the conversion of biodiesel from vegetable oil. Microwave-assisted production enables higher reaction efficiency, providing better conversion of vegetable oils. It also causes to obtain poorer characteristics of biodiesel, such as higher viscosity and density. It was aimed to improving the properties of biodiesel with microwave-assisted production and mixing it with nanoparticles to investigate the performance, combustion and emission characteristics. The influences of nanoparticle addition (carbon quantum dot) on engine performance, combustion and emissions have been analyzed in a direct injection CI engine. A single cylinder water cooled CI engine was used in the experiments. Experiments were performed at 4.12, 9.61, 15.10, 20.60 Nm and 2200 rpm. Canola biodiesel was obtained via the microwave-assisted transesterification method and mixed with diesel at the ratio of 20% (B20). 50, 100 and 150 ppm nanoparticle were added to the obtained B20 and tested in a CI engine. Specific Fuel Consumption (SFC) raised by 2.03%, 4.83%, 4.40% and 1.69% with B20, B20CQD 50 ppm, B20CQD 100 ppm and B20CQD 150 ppm respectively compared that diesel at 15.10 Nm. Remarkable reduction was found on CO, HC with B20CQD 50 ppm, B20CQD 100 ppm and B20CQD 150 ppm according to B20. In addition, an impressive reduction was realized on soot emissions with the usage of nanoprticle addition. But, NOx increased using fuel blends. As a result, the usage of quantum dot nanoparticle improved the poor properties of canola oil biodiesel and test fuels were used easily without modification in a diesel engine.
- 25 February 2025
- Published by EDP Sciences in Science and Technology for Energy Transition
- Vol. 80, 26
Open AccessImpact of carbon quantum dot nanoparticles on combustion, performance and emissions in diesel/microwave-assisted canola oil biodiesel blend
Usage of biodiesel produced with conventional transesterification methods decreases the conversion of biodiesel from vegetable oil. Microwave-assisted production enables higher reaction efficiency, providing better conversion of vegetable oils. It also causes to obtain poorer characteristics of biodiesel, such as higher viscosity and density. It was aimed to improving the properties of biodiesel with microwave-assisted production and mixing it with nanoparticles to investigate the performance, combustion and emission characteristics. The influences of nanoparticle addition (carbon quantum dot) on engine performance, combustion and emissions have been analyzed in a direct injection CI engine. A single cylinder water cooled CI engine was used in the experiments. Experiments were performed at 4.12, 9.61, 15.10, 20.60 Nm and 2200 rpm. Canola biodiesel was obtained via the microwave-assisted transesterification method and mixed with diesel at the ratio of 20% (B20). 50, 100 and 150 ppm nanoparticle were added to the obtained B20 and tested in a CI engine. Specific Fuel Consumption (SFC) raised by 2.03%, 4.83%, 4.40% and 1.69% with B20, B20CQD 50 ppm, B20CQD 100 ppm and B20CQD 150 ppm respectively compared that diesel at 15.10 Nm. Remarkable reduction was found on CO, HC with B20CQD 50 ppm, B20CQD 100 ppm and B20CQD 150 ppm according to B20. In addition, an impressive reduction was realized on soot emissions with the usage of nanoprticle addition. But, NOx increased using fuel blends. As a result, the usage of quantum dot nanoparticle improved the poor properties of canola oil biodiesel and test fuels were used easily without modification in a diesel engine.
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 182, 827-841
Multi objective optimization of HCCI combustion fuelled with fusel oil and n-heptane blends
- 1 January 2022
- Published by Elsevier in Renewable Energy
- Vol. 182, 827-841
Multi objective optimization of HCCI combustion fuelled with fusel oil and n-heptane blends
- 3 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 236 (4) , 553-568
Modeling and validation of crankshaft speed fluctuations of a single-cylinder four-stroke diesel engine
In this study, a dynamic model of a single-cylinder four-stroke diesel engine has been created, and the crankshaft speed fluctuations have been simulated and validated. The dynamic model of the engine consists of the motion equations of the piston, conrod, and crankshaft. Conrod motion was modeled by two translational and one angular motion equations, by considering the kinetic energy resulted from the mass moment of inertia and conrod mass. Motion equations involve in-cylinder gas pressure forces, hydrodynamic and dry friction, mass inertia moments of moving parts, starter moment, and external load moment. The In-cylinder pressure profile used in the model was obtained experimentally to increase the accuracy of the model. Pressure profiles were expressed mathematically using the Fourier series. The motion equations were solved by using the Taylor series method. The solution of the mathematical model was performed by coding in the MATLAB interface. Cyclic speed fluctuations obtained from the model were compared with experimental results and found compitable. A validated model was used to analyze the effects of in-cylinder pressure, mass moment of inertia of crankshaft and connecting rod, friction, and piston mass. In experiments for 1500, 1800, 2400, and 2700 rpm engine speeds, crankshaft speed fluctuations were observed as 12.84%, 8.04%, 5.02%, and 4.44%, respectively. In simulations performed for the same speeds, crankshaft speed fluctuations were calculated as 10.45%, 7.56%, 4.49%, and 3.65%. Besides, it was observed that the speed fluctuations decreased as the average crankshaft speed value increased. In the simulation for 157.07, 188.49, 219.91, 251.32, and 282.74 rad/s crankshaft speeds, crankshaft speed fluctuations occurred at rates of 10.45%, 7.56%, 5.84%, 4.49%, and 3.65%, respectively. The effective engine power was achieved as 5.25 kW at an average crankshaft angular speed of 219.91 rad/s. The power of friction loss in the engine was determined as 0.68 kW.
- 3 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 236 (4) , 553-568
Modeling and validation of crankshaft speed fluctuations of a single-cylinder four-stroke diesel engine
In this study, a dynamic model of a single-cylinder four-stroke diesel engine has been created, and the crankshaft speed fluctuations have been simulated and validated. The dynamic model of the engine consists of the motion equations of the piston, conrod, and crankshaft. Conrod motion was modeled by two translational and one angular motion equations, by considering the kinetic energy resulted from the mass moment of inertia and conrod mass. Motion equations involve in-cylinder gas pressure forces, hydrodynamic and dry friction, mass inertia moments of moving parts, starter moment, and external load moment. The In-cylinder pressure profile used in the model was obtained experimentally to increase the accuracy of the model. Pressure profiles were expressed mathematically using the Fourier series. The motion equations were solved by using the Taylor series method. The solution of the mathematical model was performed by coding in the MATLAB interface. Cyclic speed fluctuations obtained from the model were compared with experimental results and found compitable. A validated model was used to analyze the effects of in-cylinder pressure, mass moment of inertia of crankshaft and connecting rod, friction, and piston mass. In experiments for 1500, 1800, 2400, and 2700 rpm engine speeds, crankshaft speed fluctuations were observed as 12.84%, 8.04%, 5.02%, and 4.44%, respectively. In simulations performed for the same speeds, crankshaft speed fluctuations were calculated as 10.45%, 7.56%, 4.49%, and 3.65%. Besides, it was observed that the speed fluctuations decreased as the average crankshaft speed value increased. In the simulation for 157.07, 188.49, 219.91, 251.32, and 282.74 rad/s crankshaft speeds, crankshaft speed fluctuations occurred at rates of 10.45%, 7.56%, 5.84%, 4.49%, and 3.65%, respectively. The effective engine power was achieved as 5.25 kW at an average crankshaft angular speed of 219.91 rad/s. The power of friction loss in the engine was determined as 0.68 kW.
- 31 March 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (1) , 1-7
The Experimental Investigation and Nonlinear Regression Analysis of the Effect of Tire Inflation Pressure on Pitch Force
In this study, the effect of tire inflation pressure on the vehicle during braking was investigated experimentally. The experimental study was carried out in the Brake-Suspension Test Device designed as a half-vehicle model, which enables vehicle brake tests to be performed in the laboratory. During the tests, a total of nine different tire inflation pressures from 26 psi to 40 psi standard value were taken into consideration. As a result of the experiments carried out separately for each tire inflation pressure, a curve characterizing the effect of different pressure values on the pitching force was obtained. Based on the experimental results, dif-ferent mathematical models suitable for the curve obtained are derived by non-linear curve fitting. For the nonlinear curve fitting process, a hybrid iterative re-gression algorithm obtained by combining classical curve fitting algorithm with Newton-Raphson iteration method was used. It was observed that the correlation coefficients (R2) of the mathematical models obtained provided sufficient sensi-tivity to express the problem under consideration.
- 31 March 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (1) , 1-7
The Experimental Investigation and Nonlinear Regression Analysis of the Effect of Tire Inflation Pressure on Pitch Force
In this study, the effect of tire inflation pressure on the vehicle during braking was investigated experimentally. The experimental study was carried out in the Brake-Suspension Test Device designed as a half-vehicle model, which enables vehicle brake tests to be performed in the laboratory. During the tests, a total of nine different tire inflation pressures from 26 psi to 40 psi standard value were taken into consideration. As a result of the experiments carried out separately for each tire inflation pressure, a curve characterizing the effect of different pressure values on the pitching force was obtained. Based on the experimental results, dif-ferent mathematical models suitable for the curve obtained are derived by non-linear curve fitting. For the nonlinear curve fitting process, a hybrid iterative re-gression algorithm obtained by combining classical curve fitting algorithm with Newton-Raphson iteration method was used. It was observed that the correlation coefficients (R2) of the mathematical models obtained provided sufficient sensi-tivity to express the problem under consideration.
- 31 December 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (4) , 206-212
Biodiesel Production from Waste Sunflower Oil and Engine Performance Tests
In this study, biodiesel is produced from waste sunflower oil and its ef-fect on engine performance and specific fuel consumption is experimen-tally investigated. Transesterification method was used in biodiesel pro-duction of waste sunflower oil. After production, analyzes giving charac-teristics of biodiesel such as density, kinematic viscosity, sulfur and water content were made. As a result of the analysis, the biodiesel fuel with a viscosity of 4,372 mm2/s, which has a reaction temperature of 60°C, an alcohol content of 25% and a catalyst ratio of 0.05%, was cho-sen as a reference fuel, as it was observed to comply with European Standards of EN 14214. Standard diesel fuel was taken as reference for the purpose of examining the effect of biodiesel on engine performance. Performance and fuel consumption tests of the produced biodiesel and standard diesel fuel were carried out at the full load position at seven dif-ferent engine speed levels. Experiments were carried out on a single cy-linder four-stroke Cussons P8160 engine. As a result of the test, it was observed that there was a 7.06% reduction in engine moment compared to the standard diesel fuel use of B100 fuel. In addition, compared to the standard diesel fuel of B100 fuel, there was a 6.64% reduction in engine power. Specific fuel consumption values for B100 and diesel fuels at 2200 rpm engine speed were 426.75 g/kWh and 355.22 g/kWh, respecti-vely.
- 31 December 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (4) , 206-212
Biodiesel Production from Waste Sunflower Oil and Engine Performance Tests
In this study, biodiesel is produced from waste sunflower oil and its ef-fect on engine performance and specific fuel consumption is experimen-tally investigated. Transesterification method was used in biodiesel pro-duction of waste sunflower oil. After production, analyzes giving charac-teristics of biodiesel such as density, kinematic viscosity, sulfur and water content were made. As a result of the analysis, the biodiesel fuel with a viscosity of 4,372 mm2/s, which has a reaction temperature of 60°C, an alcohol content of 25% and a catalyst ratio of 0.05%, was cho-sen as a reference fuel, as it was observed to comply with European Standards of EN 14214. Standard diesel fuel was taken as reference for the purpose of examining the effect of biodiesel on engine performance. Performance and fuel consumption tests of the produced biodiesel and standard diesel fuel were carried out at the full load position at seven dif-ferent engine speed levels. Experiments were carried out on a single cy-linder four-stroke Cussons P8160 engine. As a result of the test, it was observed that there was a 7.06% reduction in engine moment compared to the standard diesel fuel use of B100 fuel. In addition, compared to the standard diesel fuel of B100 fuel, there was a 6.64% reduction in engine power. Specific fuel consumption values for B100 and diesel fuels at 2200 rpm engine speed were 426.75 g/kWh and 355.22 g/kWh, respecti-vely.
- Open Access
- 30 September 2019
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 3 (3) , 57-61
Experimental Investigation of the Effect of Brake Disconnished by Hvof Method
In this study; brake discs used in vehicles have investigated. The behavior of these discs during braking, wear and braking distance performance of the coated and uncoated surfaces during the braking process were evaluated. The surface of the commercially produced discs was coated with a thickness of 1 mm using the HVOF (High Velocity Oxy-Fuel) coating method. In the coating process CoNiCrAlY, WC-Co (88/12), NiCrBSi and MoNiCrBSiFe (Mo 25%) 4 (four) different ceramic powders were used respectively. Wear and brake distance tests of coated and uncoated discs were performed by braking in a total of 20 brakes in 15 seconds on the brake-suspension tester. After the brake tests, the surface roughness changes of the discs, surface hardness change, mass loss and the abrasion values on the disc surfaces were determined due to the brake force applied to the discs during the experiment. The most wear on the discs was on the CoNiCrAlY ceramic powder coated disc at 0,4 g, while the least wear occurred on the disc coated with NiCrBSi ceramic powder at 0,2 g.
- 30 September 2019
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 3 (3) , 57-61
Open AccessExperimental Investigation of the Effect of Brake Disconnished by Hvof Method
In this study; brake discs used in vehicles have investigated. The behavior of these discs during braking, wear and braking distance performance of the coated and uncoated surfaces during the braking process were evaluated. The surface of the commercially produced discs was coated with a thickness of 1 mm using the HVOF (High Velocity Oxy-Fuel) coating method. In the coating process CoNiCrAlY, WC-Co (88/12), NiCrBSi and MoNiCrBSiFe (Mo 25%) 4 (four) different ceramic powders were used respectively. Wear and brake distance tests of coated and uncoated discs were performed by braking in a total of 20 brakes in 15 seconds on the brake-suspension tester. After the brake tests, the surface roughness changes of the discs, surface hardness change, mass loss and the abrasion values on the disc surfaces were determined due to the brake force applied to the discs during the experiment. The most wear on the discs was on the CoNiCrAlY ceramic powder coated disc at 0,4 g, while the least wear occurred on the disc coated with NiCrBSi ceramic powder at 0,2 g.