Anja Buchwalder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anja Buchwalder has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Eugen Hegelmann
Institute of Materials Engineering, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany
2 shared publications - Jan Böcker
Institute of Materials Engineering, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany
2 shared publications - Volker Klemm
Institute of Materials Science, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany
2 shared publications - Andreas Leineweber
Institute of Materials Science , TU Bergakademie Freiberg , Gustav-Zeuner-Str. 5, 09599 Freiberg , Germany
1 shared publication - Anja Holst
Institute of Materials Engineering TU Bergakademie Freiberg Freiberg Germany
1 shared publication - Anne Jung
Institute of Materials Engineering, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany
1 shared publication
Latest Publications
- Open Access
Mechanism of Layer Formation during Gas Nitriding of Remelted Ledeburitic Surface Layers on Unalloyed Cast Irons
Unalloyed cast iron materials exhibit low tribological and corrosive resistance. In this respect, nitriding has a wide range of applications for steels. In the case of cast iron, the advantageous properties of nitrided layers are impaired by the presence of graphite. Electron beam remelting of cast iron surfaces prior to nitriding removes graphite. The homogeneous ledeburitic microstructure within the approx. 1 mm-thick remelted layer enables the formation of a dense compound layer during subsequent nitriding. The main objective of this study is to investigate the nitriding mechanism of unalloyed ledeburitic microstructures. Due to the complex relationships, investigations were carried out on both conventional ferritic and pearlitic cast irons and Fe-based model alloys containing one to four additional alloying elements, i.e., C, Si, Mn and Cu. The iron (carbo-)nitride composition (γ’, ε) of this compound layer depends on the gas nitriding conditions, the chemical composition of the substrates and the microstructural constituents. As a result, a schematic model of the nitriding mechanism is developed that includes the effects of the nitriding parameters and alloy composition on the phase composition of the nitriding layer. These findings enable targeted parameter selection and a further optimization of both the process and the properties.
Open AccessMechanism of Layer Formation during Gas Nitriding of Remelted Ledeburitic Surface Layers on Unalloyed Cast Irons
Unalloyed cast iron materials exhibit low tribological and corrosive resistance. In this respect, nitriding has a wide range of applications for steels. In the case of cast iron, the advantageous properties of nitrided layers are impaired by the presence of graphite. Electron beam remelting of cast iron surfaces prior to nitriding removes graphite. The homogeneous ledeburitic microstructure within the approx. 1 mm-thick remelted layer enables the formation of a dense compound layer during subsequent nitriding. The main objective of this study is to investigate the nitriding mechanism of unalloyed ledeburitic microstructures. Due to the complex relationships, investigations were carried out on both conventional ferritic and pearlitic cast irons and Fe-based model alloys containing one to four additional alloying elements, i.e., C, Si, Mn and Cu. The iron (carbo-)nitride composition (γ’, ε) of this compound layer depends on the gas nitriding conditions, the chemical composition of the substrates and the microstructural constituents. As a result, a schematic model of the nitriding mechanism is developed that includes the effects of the nitriding parameters and alloy composition on the phase composition of the nitriding layer. These findings enable targeted parameter selection and a further optimization of both the process and the properties.
- Open Access
Investigations on the Influence of Subsequent Electron Beam (EB) Remelting on the Microstructure of an Aluminium Nitride Layer Formed on an Aluminium Substrate (Part II)
Nitriding of Al alloys leads to the formation of a thin, hard nitride layer (AlN) on the surface. A subsequent EBR can both eliminate the nitriding-related cavities under the nitride layer and increase the hardness of the substrate without melting or destroying the nitride layer. This paper deals with investigations regarding the influence of the energy/heat input on the microstructure within both the AlN layer and the remelted Al substrate. Of particular interest was the interface between the AlN and the Al substrate, which changed to a transition zone with a depth of approximately 80 µm. A range of high-resolution imaging and analytical tools for both scanning and transmission electron microscopy were used for these investigations. Based on the findings from the microstructural investigations, a schematic model was developed of the processes occurring within the nitride layer and at the interface as a result of remelting.
Open AccessInvestigations on the Influence of Subsequent Electron Beam (EB) Remelting on the Microstructure of an Aluminium Nitride Layer Formed on an Aluminium Substrate (Part II)
Nitriding of Al alloys leads to the formation of a thin, hard nitride layer (AlN) on the surface. A subsequent EBR can both eliminate the nitriding-related cavities under the nitride layer and increase the hardness of the substrate without melting or destroying the nitride layer. This paper deals with investigations regarding the influence of the energy/heat input on the microstructure within both the AlN layer and the remelted Al substrate. Of particular interest was the interface between the AlN and the Al substrate, which changed to a transition zone with a depth of approximately 80 µm. A range of high-resolution imaging and analytical tools for both scanning and transmission electron microscopy were used for these investigations. Based on the findings from the microstructural investigations, a schematic model was developed of the processes occurring within the nitride layer and at the interface as a result of remelting.
- Open Access
Investigations on the Microstructure of an Aluminium Nitride Layer and Its Interface with the Aluminium Substrate (Part I)
In principle, the plasma nitriding of Al based substrates is a well-known process, though it remains extremely challenging from both the technological point of view and the aspect of stress loading conditions. In order to improve the latter, a duplex treatment consisting of plasma nitriding and subsequent surface remelting using electron beam technology was employed. The focus of this paper (part I) was on the characterisation of the initial microstructure after plasma nitriding. This should create the basis for a better understanding of the processes taking place or changes in the subsequent duplex treatment. This was done with the help of high-resolution imaging and analysis tools in the scanning and transmission electron microscope as well as XPS analyses. Special attention was paid to the nitriding mechanism at the interface as a function of the local microstructural constituents of the hypereutectic Al alloy substrate (Al solid solution, primary silicon, and intermetallic phases). While the main part of the nitride layer formed consisted of AlN and small fractions of pure Al in the diffusion paths, other nitrides and oxides could also be detected in the area of the interface.
Open AccessInvestigations on the Microstructure of an Aluminium Nitride Layer and Its Interface with the Aluminium Substrate (Part I)
In principle, the plasma nitriding of Al based substrates is a well-known process, though it remains extremely challenging from both the technological point of view and the aspect of stress loading conditions. In order to improve the latter, a duplex treatment consisting of plasma nitriding and subsequent surface remelting using electron beam technology was employed. The focus of this paper (part I) was on the characterisation of the initial microstructure after plasma nitriding. This should create the basis for a better understanding of the processes taking place or changes in the subsequent duplex treatment. This was done with the help of high-resolution imaging and analysis tools in the scanning and transmission electron microscope as well as XPS analyses. Special attention was paid to the nitriding mechanism at the interface as a function of the local microstructural constituents of the hypereutectic Al alloy substrate (Al solid solution, primary silicon, and intermetallic phases). While the main part of the nitride layer formed consisted of AlN and small fractions of pure Al in the diffusion paths, other nitrides and oxides could also be detected in the area of the interface.