FDFrancesco D'ELia
Francesco D'ELia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Francesco D'ELia has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Cecilia Persson
Division of Biomedical Engineering, Department of Materials Science and Engineering, Uppsala University, Uppsala, Sweden
6 shared publications - Vitalii Shtender
Uppsala University
3 shared publications - Comondore Ravindran
Centre for Near-net-shape Processing of Materials, Ryerson University, Toronto, Canada
2 shared publications - Dimitry Sediako
High-Performance Powertrain Materials Laboratory, University of British Columbia, 1137 Alumni Ave, Kelowna, BC V1V 1V7, Canada
2 shared publications A. Machin
Centre for Near-net-shape Processing of Materials, Ryerson University; 1 Gerrard St. E; Toronto, ON, M5B 2K3, Canada
1 shared publication- Abdallah Elsayed
School of Engineering, University of Guelph, Guelph, ON N1G 2W1, Canada
1 shared publication
Latest Publications
- Open Access
- 1 November 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 24
Microstructure-driven formation of a chemically graded corrosion layer in PBF-LB/M fabricated dual-phase Mg–8Li–0.5Ca wt.% ultralight alloy
- 1 November 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 24
Open AccessMicrostructure-driven formation of a chemically graded corrosion layer in PBF-LB/M fabricated dual-phase Mg–8Li–0.5Ca wt.% ultralight alloy
- Open Access
- 23 September 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1082
Influence of Mg content on microstructure and mechanical properties of lean (< 1 wt.%) powder-mixed Zn–Mg alloys processed by PBF-LB
- 23 September 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1082
Open AccessInfluence of Mg content on microstructure and mechanical properties of lean (< 1 wt.%) powder-mixed Zn–Mg alloys processed by PBF-LB
- Open Access
- 5 November 2025
- Published by Elsevier in Applied Materials Today
- Vol. 47
Additively manufactured WE43 for biodegradable urinary devices: Exploring the corrosion profile under in vitro urinary tract conditions
- 5 November 2025
- Published by Elsevier in Applied Materials Today
- Vol. 47
Open AccessAdditively manufactured WE43 for biodegradable urinary devices: Exploring the corrosion profile under in vitro urinary tract conditions
- Open Access
- 28 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 5498-5510
Powder reuse in powder bed fusion-laser beam of WE43 magnesium alloy: towards sustainable manufacturing of biodegradable implants
- 28 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 5498-5510
Open AccessPowder reuse in powder bed fusion-laser beam of WE43 magnesium alloy: towards sustainable manufacturing of biodegradable implants
- Open Access
- 23 June 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 2352-2363
Engineering graded microstructures in a Ti alloy through high-cycle laser rescanning in powder bed fusion – Laser beam
- 23 June 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 2352-2363
Open AccessEngineering graded microstructures in a Ti alloy through high-cycle laser rescanning in powder bed fusion – Laser beam
- Open Access
- 20 November 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 162, 106826
Towards improved functionality of mandibular reconstruction plates enabled by additively manufactured triply periodic minimal surface structures
- 20 November 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 162, 106826
Open AccessTowards improved functionality of mandibular reconstruction plates enabled by additively manufactured triply periodic minimal surface structures
- Open Access
- 1 January 2024
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 157, 213756
Combined severe plastic deformation processing of commercial purity titanium enables superior fatigue resistance for next generation implants
- 1 January 2024
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 157, 213756
Open AccessCombined severe plastic deformation processing of commercial purity titanium enables superior fatigue resistance for next generation implants
- Open Access
Observing the Effect of Grain Refinement on Crystal Growth of Al and Mg Alloys during Solidification Using In-Situ Neutron Diffraction
The present research uses in-situ neutron diffraction to examine the effect of grain refinement on grain growth during solidification of Al-5 wt.% Cu and Mg-5 wt.% Zn alloys. The alloys were grain refined through additions of Al-5Ti-1B and Zr, respectively. The in-situ neutron diffraction experiments were carried out by heating the alloys to temperatures above the liquidus and subsequently cooling in 5 or 10 °C temperature steps to temperatures below solidus, while being irradiated by thermal neutrons. With the addition of grain refiners, grain size reductions of 92% were observed for both the Al-5 wt.% Cu and Mg-5 wt.% Zn alloys. The refined and unrefined Al-5 wt.% Cu alloys contained α-Al with Al2Cu along the grain boundary regions. Differences in Al2Cu morphology were observed in the grain refined alloys. The Mg-5 wt.% Zn alloy contained MgZn intermetallic phases with primary Mg. The refined Mg-5 wt.% Zn-0.7 wt.% Zr alloy contained Mg, MgZn and Zn2Zr phases. In-situ neutron diffraction enabled quantification of individual plane solid fraction growth for the α-Al and Al2Cu phases in the Al-Cu alloys, and for α-Mg in the Mg alloys. For the unrefined Al-5 wt.% Cu, the coarse microstructure resulted in a rapid solid fraction rise at temperatures just below liquidus followed by a gradual increase in solid fraction until the sample was fully solid. The grain-refined Al-5 wt.% Cu alloys showed a columnar to equiaxed microstructure transition and a more gradual growth in fraction solid throughout solidification. For the Mg-5 wt.% Zn alloy, the more packed and α-Mg plane intensities grew at a slower rate than the plane intensity, resulting in an irregular grain structure. With the addition of the Zr grain refiner, the Mg-5 wt.% Zn-0.7 wt.% Zr alloy had , and planes intensities all increasing at similar rates, especially at the early stages of solidification. FactSage™ (version 6.4, Montréal, QC, Canada) equilibrium solidification models followed the fraction solid curves developed by tracking the fastest growing planes of the Mg alloys.Open AccessObserving the Effect of Grain Refinement on Crystal Growth of Al and Mg Alloys during Solidification Using In-Situ Neutron Diffraction
The present research uses in-situ neutron diffraction to examine the effect of grain refinement on grain growth during solidification of Al-5 wt.% Cu and Mg-5 wt.% Zn alloys. The alloys were grain refined through additions of Al-5Ti-1B and Zr, respectively. The in-situ neutron diffraction experiments were carried out by heating the alloys to temperatures above the liquidus and subsequently cooling in 5 or 10 °C temperature steps to temperatures below solidus, while being irradiated by thermal neutrons. With the addition of grain refiners, grain size reductions of 92% were observed for both the Al-5 wt.% Cu and Mg-5 wt.% Zn alloys. The refined and unrefined Al-5 wt.% Cu alloys contained α-Al with Al2Cu along the grain boundary regions. Differences in Al2Cu morphology were observed in the grain refined alloys. The Mg-5 wt.% Zn alloy contained MgZn intermetallic phases with primary Mg. The refined Mg-5 wt.% Zn-0.7 wt.% Zr alloy contained Mg, MgZn and Zn2Zr phases. In-situ neutron diffraction enabled quantification of individual plane solid fraction growth for the α-Al and Al2Cu phases in the Al-Cu alloys, and for α-Mg in the Mg alloys. For the unrefined Al-5 wt.% Cu, the coarse microstructure resulted in a rapid solid fraction rise at temperatures just below liquidus followed by a gradual increase in solid fraction until the sample was fully solid. The grain-refined Al-5 wt.% Cu alloys showed a columnar to equiaxed microstructure transition and a more gradual growth in fraction solid throughout solidification. For the Mg-5 wt.% Zn alloy, the more packed and α-Mg plane intensities grew at a slower rate than the plane intensity, resulting in an irregular grain structure. With the addition of the Zr grain refiner, the Mg-5 wt.% Zn-0.7 wt.% Zr alloy had , and planes intensities all increasing at similar rates, especially at the early stages of solidification. FactSage™ (version 6.4, Montréal, QC, Canada) equilibrium solidification models followed the fraction solid curves developed by tracking the fastest growing planes of the Mg alloys. - Open Access
- 28 February 2011
- Published by Wiley
- p. 299-308
Application of Neutron Diffraction in Analysis of Residual Stress Profiles in the Cylinder Web Region of an as‐Cast V6 Al Engine Block with Cast‐In Fe Liners
- 28 February 2011
- Published by Wiley
- p. 299-308
Open AccessApplication of Neutron Diffraction in Analysis of Residual Stress Profiles in the Cylinder Web Region of an as‐Cast V6 Al Engine Block with Cast‐In Fe Liners