Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ziomara De la Cruz-Barragán has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Evaluation of an Energy Generation and Storage System Based on a Concentration Redox Flow Battery Coupled to Solar Power

    by Elier Sandoval-Sánchez, Ziomara De la Cruz-Barragán, David García-Bassoco, Paola Roncagliolo-Barrera, David Morillón, Edgar Mendoza

    The increasing integration of renewable energy sources, such as solar photovoltaics, requires low-cost, scalable energy storage solutions suitable for decentralized systems. This work experimentally evaluates an iron chloride concentration redox flow battery (FeCl-CFB) coupled to a photovoltaic system. The battery, which employs the Fe2+/Fe3+ redox couple to store energy through a chemical concentration gradient, was electrochemically characterized using different carbon-based electrode materials and operated under solar charging for 25 charge–discharge cycles. A maximum power density of 6.3 W·m−2 was achieved at the cell level, with stable cycling behavior under variable solar irradiance. Coulombic and energy efficiencies remained within ranges of 63–72% and 20–28%, respectively, throughout the cycles. Despite these moderate efficiencies, the system demonstrated a consistent and functional usable capacity. The main limitation identified was a decrease in maximum power after prolonged cycling, attributable to resistance and polarization losses rather than electrolyte instability. These preliminary results characterize the initial performance of the FeCl-CFB under solar-driven conditions, highlighting significant efficiency and stability challenges that must be addressed through further optimization to determine the future potential for decentralized energy storage.

  • Open Access

    Practical Methodology for a Three-Dimensional-Printed Hybrid Desalination System

    by Ziomara De la Cruz-Barragán, Elier Sandoval-Sánchez, Jonathan Israel Hernández-Hernández, Margarita Miranda-Hernández, Edgar Mendoza

    In response to the growing demand for potable water, this study presents a practical methodology for designing and fabricating a hybrid desalination system that integrates reverse electrodialysis and electrodialysis using 3D-printing technology. The hybrid system combines the energy generation potential of RED with the salt removal capabilities of ED, reducing energy consumption. Customized reactors were designed to enhance flow distribution and ion exchange, with computational fluid dynamics simulations validating the hydrodynamic performance. The reactors were fabricated using 3D printing, allowing rapid, cost-effective production, with functional reactors constructed in under 24 h. The system achieved a 15% reduction in salt concentration within one hour, with a specific energy consumption of 0.1388 Wh/m3 and a water recovery rate of 50%. These results demonstrate the functionality of the RED-ED hybrid system for achieving energy savings and performing water desalination. This methodology provides a scalable and replicable solution for water treatment applications, especially in regions with abundant salinity gradients and limited freshwater resources, while offering a multidisciplinary approach that integrates physicochemical and engineering principles for effective device development.

  • Open Access

    Effect of Gaskets Geometry on the Performance of a Reverse Electrodialysis Cell

    by Elier Sandoval-Sánchez, Ziomara De la Cruz-Barragán, Margarita Miranda-Hernández, Edgar Mendoza

    Salinity gradient energy (SGE) allows the difference in salt concentration in two volumes of water to be harnessed and transformed into clean energy. The most advanced SGE technology is reverse electrodialysis (RED) cells. Recent studies have focused on ways to optimize the flow distribution in the compartments containing the water, for which it is necessary to consider the characteristics of the solutions, the cell dimensions, the operating conditions, as well as their influence on the hydrodynamics and mass transport in the system. In this study, two spacers with different gasket geometry were designed, fabricated, and compared experimentally through voltage and current measurements. The power output was computed, obtaining a maximum power density of 0.14 W/m2. Results show that the geometry of the cell components directly influences the physicochemical principles governing the RED process and is closely related to the cell output parameters. In turn, it is possible to increase the performance of a RED cell by optimizing the gasket geometry by reducing dead zones.