Helge Pfeiffer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Helge Pfeiffer has a total of 146 co-authors. Here are the top co-authors by number of shared publications:
- Martine Wevers
Department of Materials Engineering, KU Leuven, 3001 Leuven, Belgium
24 shared publications Karel Heremans
10 shared publicationsK. Heremans
8 shared publicationsG. Klose
6 shared publicationsFilip Meersman
5 shared publications- Hans Binder
Interdisciplinary Centre for Bioinformatics (IZBI), University of Leipzig, Leipzig, Germany
4 shared publications
Latest Publications
- Open Access
- 1 April 2025
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 30 (4)
Detecting Water in Honeycomb Composites by Acoustic Emission during Freezing or Melting
Water trapped in sandwich honeycomb composites—due to defects, diffusion, or other factors—is a major concern, especially in aircraft maintenance. In this paper, we present a method based on acoustic emissions for the quick assessment of possible water ingress that can be performed when a structure is exposed to freezing or melting conditions, such as during ascent or descent in high-altitude flights or after landing. A quantitative analysis, including exponential decay models and amplitude and frequency distributions, confirm that melting ice can be detected not only locally but also in its vicinity. The presented method is compared with respect to active ultrasonic transmission tests.
- 1 April 2025
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 30 (4)
Open AccessDetecting Water in Honeycomb Composites by Acoustic Emission during Freezing or Melting
Water trapped in sandwich honeycomb composites—due to defects, diffusion, or other factors—is a major concern, especially in aircraft maintenance. In this paper, we present a method based on acoustic emissions for the quick assessment of possible water ingress that can be performed when a structure is exposed to freezing or melting conditions, such as during ascent or descent in high-altitude flights or after landing. A quantitative analysis, including exponential decay models and amplitude and frequency distributions, confirm that melting ice can be detected not only locally but also in its vicinity. The presented method is compared with respect to active ultrasonic transmission tests.
- Open Access
- 1 October 2024
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 29 (10)
Acoustic emission during the freezing of water or the melting of ice in aircraft
It is a frequently overlooked phenomenon that matter can produce sound emissions when undergoing a phase transition. The exact cause of this sound is until now not modeled and understood in depth, but it appears certain that sudden volume changes, cracks, friction, and other sources that occur during e.g. crystal decay/growth in melting/freezing processes must be considered. However, a generally accepted theory of the "sound of phase transitions" is lacking. In this paper we present a general introduction in this field. Besides the more fundamental aspects, the AE generation during the melting of ice can be used to detect the presence of this respective substance in technical structures. An interesting application is to detect the melting ice in aircraft. Adverse water accumulation, resulting from contamination and condensation, is regularly found in fuel tanks, and scheduled drainage procedures of this water after the melting of the ice are important to ensure the safety of systems and structures. A practical problem for drainage after flight is determining the right time to start the process. Beginning too early would mean that the remaining ice cannot be removed, and waiting too long presents an economic problem as it increases the aircraft's downtime. There is currently no technology that reports when all water has melted. To realize this goal acoustic sensors were attached to the skin of the tank walls, and the acoustic signals were intense enough to propagate through the aluminum sheets and coating and further analyzed. In this way, the completion of the melting of ice was determined by the time at which the acoustic emission stopped. We present measurements on a laboratory scale, the results from a climate chamber on relevant replica’s, and the outcome of a first campaign on an operational aircraft (Airbus A330).
- 1 October 2024
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 29 (10)
Open AccessAcoustic emission during the freezing of water or the melting of ice in aircraft
It is a frequently overlooked phenomenon that matter can produce sound emissions when undergoing a phase transition. The exact cause of this sound is until now not modeled and understood in depth, but it appears certain that sudden volume changes, cracks, friction, and other sources that occur during e.g. crystal decay/growth in melting/freezing processes must be considered. However, a generally accepted theory of the "sound of phase transitions" is lacking. In this paper we present a general introduction in this field. Besides the more fundamental aspects, the AE generation during the melting of ice can be used to detect the presence of this respective substance in technical structures. An interesting application is to detect the melting ice in aircraft. Adverse water accumulation, resulting from contamination and condensation, is regularly found in fuel tanks, and scheduled drainage procedures of this water after the melting of the ice are important to ensure the safety of systems and structures. A practical problem for drainage after flight is determining the right time to start the process. Beginning too early would mean that the remaining ice cannot be removed, and waiting too long presents an economic problem as it increases the aircraft's downtime. There is currently no technology that reports when all water has melted. To realize this goal acoustic sensors were attached to the skin of the tank walls, and the acoustic signals were intense enough to propagate through the aluminum sheets and coating and further analyzed. In this way, the completion of the melting of ice was determined by the time at which the acoustic emission stopped. We present measurements on a laboratory scale, the results from a climate chamber on relevant replica’s, and the outcome of a first campaign on an operational aircraft (Airbus A330).
- Open Access
Defect Detection in Carbon Fiber-Reinforced Plate by Imaging of Mechanical Nonlinearity-Induced Sideband Vibrations
Laser Doppler scanning vibrometry is used for imaging spectral vibration components in a carbon fiber-reinforced composite plate that contains a sub-surface delamination defect caused by hammer impact. The images reveal sideband generation at the location of the defect, reflecting mechanical nonlinearity-induced mixing between a high amplitude, low-frequency vibration that modulates the stress–strain behavior near the defect and a low amplitude, high-frequency probe vibration. In this work, a multifrequency probe is used to tackle the problem that the mixing coefficients are, in practice, frequency dependent. Based on the measured sideband amplitudes, a study is presented on the expected feasibility of detecting defects by a full field imaging scheme based on a photorefractive interferometer that is configured as a vibrometer acting as a bandpass filter around a sideband frequency of interest.
Open AccessDefect Detection in Carbon Fiber-Reinforced Plate by Imaging of Mechanical Nonlinearity-Induced Sideband Vibrations
Laser Doppler scanning vibrometry is used for imaging spectral vibration components in a carbon fiber-reinforced composite plate that contains a sub-surface delamination defect caused by hammer impact. The images reveal sideband generation at the location of the defect, reflecting mechanical nonlinearity-induced mixing between a high amplitude, low-frequency vibration that modulates the stress–strain behavior near the defect and a low amplitude, high-frequency probe vibration. In this work, a multifrequency probe is used to tackle the problem that the mixing coefficients are, in practice, frequency dependent. Based on the measured sideband amplitudes, a study is presented on the expected feasibility of detecting defects by a full field imaging scheme based on a photorefractive interferometer that is configured as a vibrometer acting as a bandpass filter around a sideband frequency of interest.
- Open Access
- 12 September 2023
- Published by DEStech Publications
MONITORING OF FREEZING WATER OR MELTING ICE IN AIRCRAFT FUEL TANKS AND FUSELAGES BY ACOUSTIC EMISSION
It is a mostly overlooked phenomenon in physical chemistry that matter produces characteristic sound emissions when passing through a phase transition. The origin of this sound is not yet fully understood, but it is certain that sudden changes in volume, cracks, friction between crystallites and other sources must be considered, but a generally accepted theory of the "sound of phase transitions" is lacking. But even if the cause is not completely clear, this phenomenon can be used to detect the presence of these substances in technical structures. This is important, for example, in the case of water and ice in aircraft fuel tanks. Water arising from contamination and condensation is frequently found in fuel tanks and regular drainage procedure are important to guarantee the safety of systems and structures. While ice dispersed in the kerosene phase can seriously hinder the combustion process, blocks of ice can cause serious crack formation as in valves and tubes. A practical problem with all drainage procedures after flights at freezing conditions is the right time to start that process. Starting too early would mean that the remaining ice cannot be removed and waiting too long is an economic problem because it increases the aircraft's downtime. Unfortunately, there is no technology yet that tells mechanics when all the water has melted. It would be beneficial for maintenance teams to find the right time to drain, and acoustic emissions from the melting ice would be the ideal tool to determine this moment. For this purpose, acoustic sensors are attached to the skin of the tank walls, and the acoustic signals from the ice are intense enough to propagate through media, the aluminum sheets and coating. In this way, the completion of the ice melt is determined by the time at which the acoustic emission stops. We present measurements on a laboratory scale, results from a realistic climate chamber on a tank model and the first results from a campaign on an operational aircraft (Airbus A330). We were able to show that relevant amounts of melted ice can be reliably determined, e.g., 30 ml of water under the kerosene phase in a replica fuel tank generate about 200,000 distinguishable signals, in our case these signals are acoustic transients. This is quite sufficient to obtain the desired information about the state of the melting ice. In addition, to address other structures, results of ice melting and water freezing processes on an aircraft fuselage model are presented.
- 12 September 2023
- Published by DEStech Publications
Open AccessMONITORING OF FREEZING WATER OR MELTING ICE IN AIRCRAFT FUEL TANKS AND FUSELAGES BY ACOUSTIC EMISSION
It is a mostly overlooked phenomenon in physical chemistry that matter produces characteristic sound emissions when passing through a phase transition. The origin of this sound is not yet fully understood, but it is certain that sudden changes in volume, cracks, friction between crystallites and other sources must be considered, but a generally accepted theory of the "sound of phase transitions" is lacking. But even if the cause is not completely clear, this phenomenon can be used to detect the presence of these substances in technical structures. This is important, for example, in the case of water and ice in aircraft fuel tanks. Water arising from contamination and condensation is frequently found in fuel tanks and regular drainage procedure are important to guarantee the safety of systems and structures. While ice dispersed in the kerosene phase can seriously hinder the combustion process, blocks of ice can cause serious crack formation as in valves and tubes. A practical problem with all drainage procedures after flights at freezing conditions is the right time to start that process. Starting too early would mean that the remaining ice cannot be removed and waiting too long is an economic problem because it increases the aircraft's downtime. Unfortunately, there is no technology yet that tells mechanics when all the water has melted. It would be beneficial for maintenance teams to find the right time to drain, and acoustic emissions from the melting ice would be the ideal tool to determine this moment. For this purpose, acoustic sensors are attached to the skin of the tank walls, and the acoustic signals from the ice are intense enough to propagate through media, the aluminum sheets and coating. In this way, the completion of the ice melt is determined by the time at which the acoustic emission stops. We present measurements on a laboratory scale, results from a realistic climate chamber on a tank model and the first results from a campaign on an operational aircraft (Airbus A330). We were able to show that relevant amounts of melted ice can be reliably determined, e.g., 30 ml of water under the kerosene phase in a replica fuel tank generate about 200,000 distinguishable signals, in our case these signals are acoustic transients. This is quite sufficient to obtain the desired information about the state of the melting ice. In addition, to address other structures, results of ice melting and water freezing processes on an aircraft fuselage model are presented.
- Open Access
- 25 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 11 (1) , 132
In-Plane Heatwave Thermography as Digital Inspection Technique for Fasteners in Aircraft Fuselage Panels
The inspection of fasteners in aluminium joints in the aviation industry is a time consuming and costly but mandatory task. Until today, the manual procedure with the bare eye does not allow the temporal tracking of a damaging behavior or the objective comparison between different inspections. A digital inspection method addresses both aspects while resulting in a significant inspection time reduction. The purpose of this work is to develop a digital and automated inspection method based on In-plane Heatwave Thermography and the analysis of the disturbances due to thermal irregularities in the plate-like structure. For this, a comparison study with Ultrasound Lock-in Thermography and Scanning Laser Doppler Vibrometry as well as a benchmarking of all three methods on one serviceable aircraft fuselage panel is performed. The presented data confirm the feasibility to detect and to qualify countersunk rivets and screws in aluminium aircraft fuselage panels with the discussed methods. The results suggest a fully automated inspection procedure which combines the different approaches and a study with more samples to establish thresholds indicating intact and damaged fasteners.
- 25 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 11 (1) , 132
Open AccessIn-Plane Heatwave Thermography as Digital Inspection Technique for Fasteners in Aircraft Fuselage Panels
The inspection of fasteners in aluminium joints in the aviation industry is a time consuming and costly but mandatory task. Until today, the manual procedure with the bare eye does not allow the temporal tracking of a damaging behavior or the objective comparison between different inspections. A digital inspection method addresses both aspects while resulting in a significant inspection time reduction. The purpose of this work is to develop a digital and automated inspection method based on In-plane Heatwave Thermography and the analysis of the disturbances due to thermal irregularities in the plate-like structure. For this, a comparison study with Ultrasound Lock-in Thermography and Scanning Laser Doppler Vibrometry as well as a benchmarking of all three methods on one serviceable aircraft fuselage panel is performed. The presented data confirm the feasibility to detect and to qualify countersunk rivets and screws in aluminium aircraft fuselage panels with the discussed methods. The results suggest a fully automated inspection procedure which combines the different approaches and a study with more samples to establish thresholds indicating intact and damaged fasteners.
- Open Access
- 29 January 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (13)
Understanding the Dehydration Stress in Lipid Vesicles by a Combined Quartz Crystal Microbalance and Dielectric Spectroscopy Study
- 29 January 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (13)
Open AccessUnderstanding the Dehydration Stress in Lipid Vesicles by a Combined Quartz Crystal Microbalance and Dielectric Spectroscopy Study
- Open Access
- 9 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (24) , 5387
Using Acoustic Emission Measurements for Ice-Melting Detection
Aircraft operators being faced with water accumulation in fuel tanks on a daily basis and are looking for reliable detection systems to determine the remaining amount of accumulated ice during maintenance after flight. Using such a technology, an increase in the safety and efficiency of the aircraft operation would be possible in this highly competitive market. This article presents the use of the Acoustic Emission Technique (AE) for the reliable and non-invasive monitoring of the melting of ice in fuel tanks. This technology is in principle based on the fact that a phase transition comes frequently along with stress relaxation that can be used for monitoring the process. Therefore, the melting of water can, in essence, be monitored with AE without accessing the ice directly. The analysis of the AE signals has been carried out in the time domain since it was the melting of ice needed to be monitored as a function of temperature rise time. The insights presented in this paper can possibly lead to new technologies for ice detection, especially in remote areas that are not easily accessible with other techniques.
- 9 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (24) , 5387
Open AccessUsing Acoustic Emission Measurements for Ice-Melting Detection
Aircraft operators being faced with water accumulation in fuel tanks on a daily basis and are looking for reliable detection systems to determine the remaining amount of accumulated ice during maintenance after flight. Using such a technology, an increase in the safety and efficiency of the aircraft operation would be possible in this highly competitive market. This article presents the use of the Acoustic Emission Technique (AE) for the reliable and non-invasive monitoring of the melting of ice in fuel tanks. This technology is in principle based on the fact that a phase transition comes frequently along with stress relaxation that can be used for monitoring the process. Therefore, the melting of water can, in essence, be monitored with AE without accessing the ice directly. The analysis of the AE signals has been carried out in the time domain since it was the melting of ice needed to be monitored as a function of temperature rise time. The insights presented in this paper can possibly lead to new technologies for ice detection, especially in remote areas that are not easily accessible with other techniques.
- Open Access
- 1 December 2019
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 90 (12) , 125106
A compact device for simultaneous dielectric spectroscopy and microgravimetric analysis under controlled humidity
Water plays a key role in the functioning of natural and synthetic molecular systems. Despite several hydration studies, different techniques are employed individually for monitoring different physical features such as kinetics, dynamics, and absorption. This study describes a compact hydration cell that enables simultaneous dielectric relaxation spectroscopy (DRS) and mass loss/uptake measurements in thin organic layers under controlled humidity conditions and in a wide temperature range. This approach enabled us to correlate the physical quantities obtained during the same experiment by complementary techniques. To demonstrate the performance of this device, a 200 nm thick poly(methyl methacrylate) (PMMA) layer was measured at various relative humidity levels (0%–75%), temperatures (25–75 °C), and frequencies (DRS: 0.1 Hz–1 MHz) to study how hydration and dehydration processes affect its molecular dynamics. The results show the capability of this setup to study the changes in the PMMA film regarding the kinetics and molecular dynamics upon variation of the water content.
- 1 December 2019
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 90 (12) , 125106
Open AccessA compact device for simultaneous dielectric spectroscopy and microgravimetric analysis under controlled humidity
Water plays a key role in the functioning of natural and synthetic molecular systems. Despite several hydration studies, different techniques are employed individually for monitoring different physical features such as kinetics, dynamics, and absorption. This study describes a compact hydration cell that enables simultaneous dielectric relaxation spectroscopy (DRS) and mass loss/uptake measurements in thin organic layers under controlled humidity conditions and in a wide temperature range. This approach enabled us to correlate the physical quantities obtained during the same experiment by complementary techniques. To demonstrate the performance of this device, a 200 nm thick poly(methyl methacrylate) (PMMA) layer was measured at various relative humidity levels (0%–75%), temperatures (25–75 °C), and frequencies (DRS: 0.1 Hz–1 MHz) to study how hydration and dehydration processes affect its molecular dynamics. The results show the capability of this setup to study the changes in the PMMA film regarding the kinetics and molecular dynamics upon variation of the water content.
- 21 February 2019
- Published by Springer Nature
- p. 482-493
Moisture Climate Monitoring in Confined Spaces Using Percolation Sensors
- 21 February 2019
- Published by Springer Nature
- p. 482-493
Moisture Climate Monitoring in Confined Spaces Using Percolation Sensors
- Open Access
- 1 January 2019
- Published by Acoustical Society of America (ASA) in Proceedings of Meetings on Acoustics
- Vol. 38 (1) , 030013
Laser ultrasonic inspection for crack detection in a rotating tube under dynamic load
Laser-based ultrasonic inspection is an emerging versatile non-contact technique for defect detection in a variety of critical components. This article reports on the adaptation of this method for the inspection of rotating cylindrical components undergoing varying stress, by detecting the dynamically changing mechanical response of cracks, which goes along with modulation of the guided acoustic waves that encounter the cracks. Optical interferometry was used for the remote detection of photo-acoustically generated guided waves. An application of laser ultrasonic to investigate guided waves and their interaction with cracks detected by a laser Doppler velocimetry (LDV) on cylindrical structures under dynamically changing stress is presented. Mode conversion, which occurs when guided waves are encountering a crack, is also investigated. The experimentally assessed effects of defects on the envelope, spectrum and other receiving wave characteristics are analysed and exploited for their detection and characterization, giving a basis for the use of laser ultrasonic for Non Destructive Testing (NDT).
- 1 January 2019
- Published by Acoustical Society of America (ASA) in Proceedings of Meetings on Acoustics
- Vol. 38 (1) , 030013
Open AccessLaser ultrasonic inspection for crack detection in a rotating tube under dynamic load
Laser-based ultrasonic inspection is an emerging versatile non-contact technique for defect detection in a variety of critical components. This article reports on the adaptation of this method for the inspection of rotating cylindrical components undergoing varying stress, by detecting the dynamically changing mechanical response of cracks, which goes along with modulation of the guided acoustic waves that encounter the cracks. Optical interferometry was used for the remote detection of photo-acoustically generated guided waves. An application of laser ultrasonic to investigate guided waves and their interaction with cracks detected by a laser Doppler velocimetry (LDV) on cylindrical structures under dynamically changing stress is presented. Mode conversion, which occurs when guided waves are encountering a crack, is also investigated. The experimentally assessed effects of defects on the envelope, spectrum and other receiving wave characteristics are analysed and exploited for their detection and characterization, giving a basis for the use of laser ultrasonic for Non Destructive Testing (NDT).