Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yana N. Savina has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A combined method for producing defect-free ingots of the high-entropy alloy TiZrAlVCr and their use as cathode targets for coating deposition

    by Ya. N. Savina, R. R. Valiev, V. V. Sanin, L. Yu. Mezhevaya, M. V. Zhivotvorev, Yu. M. Modina, A. Yu. Nazarov, K. N. Ramazanov, Я. Н. Савина, Р. Р. Валиев, et al.

    This article presents the results of producing a high-entropy alloy of the Ti–Zr–Al–V–Cr system, intended for practical use as cathode targets in NNV-6.6 vacuum arc systems, using a combined method of melting and remelting. It is shown that direct remelting of the components by vacuum arc melting (VAM) in a copper mould leads to cracking of ingots due to high thermal stresses (cooling rate of 10 2 –10 3 °C/s), while switching off cooling causes copper contamination. To solve the problem, a combined method is proposed: preliminary melting of the components by VAM, followed by vacuum induction remelting (VIM) and casting into a mold. A special ceramic lining based on oxides containing up to 2 wt. % rare-earth metal oxides was used, ensuring minimal impurity contamination. The optimal crystallization parameters were selected: reduction of the cooling rate to 5–10 °C/s, use of a copper base plate for directional heat extraction and a feeder head to compensate for shrinkage effects. Scanning electron microscopy and energy-dispersive X -ray spectroscopy confirmed the chemical homogeneity of the resulting ingots (the contents of Ti, Zr, Al, V, and Cr were 16–27 at. %). The microhardness of the alloy was 768–789 HV with high reproducibility across batches. The cathode targets were successfully tested in the NNV-6.6-I1 installation: single-layer and two types of multilayer coatings were deposited on substrates made of Ti–6Al–4V titanium alloy. The developed technology ensures the production of defect-free ingots of a specified geometry (\(\emptyset \)80–85 mm, h = 45 mm), suitable for industrial use in vacuum arc deposition processes for protective coatings.

  • Open Access

    Mechanical Properties of High-Entropy Coatings of the (TiZrVCrAl)N System of Different Architectures Deposited by the Arc-PVD Method on the Surface of Ti-6Al-4V Alloy

    by Yana N. Savina, Roman R. Valiev, Stanislav V. Ovchinnikov, Almaz Yu. Nazarov, Iuliia M. Modina, Aleksey A. Nikolaev, Kamil’ N. Ramazanov, Vitaly V. Sanin, Liliya Yu. Mezhevaia, Elina R. Kasimova, et al.

    In this work, for the first time, we applied and determined the mechanical characteristics of protective coatings made of high-entropy alloy (TiZrVCrAl)N with different architectures onto the surface of Ti-6Al-4V alloy with the initial coarse-grained and ultrafine-grained structure using arc physical vapor deposition. We designed and prepared three coating architectures: a monolayer nitride coating (TiZrVCrAl)N, a multilayer coating consisting of nine alternating layers of TiZrVCrAl and (TiZrVCrAl)N, and a multilayer coating consisting of 720 alternating layers of (TiZrVCrAl)N and TiN, with a total thickness not exceeding 2 microns. We evaluated their protective performances by nanoindentation and scratch tests. Importantly, the effect of the substrate microstructure on the coatings’ performance is investigated by comparing their mechanical behavior on coarse-grained and ultrafine-grained Ti-6Al-4V. Our experimental results show that the coating performance improves with increasing number of layers in the coating, and this effect is even more pronounced for the multilayer coating deposited on the ultrafine-grained titanium alloy substrate. We also find that the (TiZrVCrAl)N/TiN (720 layers) multilayer coating deposited on the UFG Ti-6Al-4V alloy substrate exhibits the highest H/E- and H3/E2-values, indicating the coating’s high innovative potential for performance in extreme conditions. The origins of this phenomenon are analyzed and discussed.


  • High-Rate Erosion of VT6 Titanium Alloy with ZrN Protective Coating

    by S. A. Atroshenko, R. Z. Valiev, N. A. Kazarinov, N. F. Morozov, R. R. Valiev, Ya. N. Savina, M. N. Antonova, A. D. Evstifeev

    We report an experimental study of the wear and fracture of ZrN-coated VT6 alloy in its coarse-grained (as-prepared) and ultrafine-grained states during high-rate dynamic erosion by solid corundum particles with an average size of 109, 58, and 23 μm in an air flow at velocities in the range 50–250 m/s and exposure times of 30, 60, and 300 s. The experimental data were used to determine the fraction of viscous fracture, the erosion damage depth, the change in the microstructure of the coated and uncoated alloy near the erosion surface, and also the weight wear and surface roughness. The results demonstrate that, in the case of high-rate erosion, the alloy wear and damage processes depend significantly on the exposure time, erosion rate (velocity of abrasive particles), powder particle size, and substrate structure.

  • Microstructure and Properties of Protective Ion-Plasma Coating on UFG Ti Alloy

    by Ya. N. Savina, S. V. Ovchinnikov, R. R. Valiev, K. S. Selivanov

    The paper presents results of comprehensive studies on a fine structure of TiVN ion-plasma protective coating deposited on a Ti–6Al–4V substrate with an ultrafine-grained (UFG) structure. This coating considerably improves the performance properties of critical products operating under high loads in aggressive environments. In the article special attention is paid to features of formation of coating layers and their phase composition with account of effect caused the substrate ultrafine-grained structure. It is established that TiVN functional coating has a layered structure with thin layers of dark and light colors, which can be formed at different ratios of Ti and V concentrations due to planetary rotation of substrates. The structure of a TiVN functional layer is columnar and has an average diameter of about 17 nm. Based on microdiffraction patterns of a TiVN layer, it is found that the reflexes correspond to an fcc structure, which does not have a dominant textural component of growth. This might be conditioned by high level of ion activation of growth and multicomponent nature of the coating being terms for creation and retention of high density of defects. This fine structure of ion-plasma coating on a substrate with UFG structure provides the achievement of high adhesion and erosion resistance.

  • Open Access

    Microstructure and strength of a 3D-printed Ti–6Al–4V alloy subjected to high-pressure torsion

    by Emi I. Usmanov, Yana N. Savina, Roman R. Valiev

    Currently, one of the effective 3D printing methods is wire-feed electron-beam additive manufacturing (EBAM), which allows producing large-sized commercial billets from Ti–6Al–4V titanium alloy. However, Ti–6Al–4V alloy produced by this method demonstrates reduced strength properties. It is known that it is possible to increase the strength properties of metallic materials by refining their grain structure by high-pressure torsion (HPT). This work is aimed at studying the influence of high-pressure torsion on the microstructure, and mechanical strength of a structural Ti–6Al–4V titanium alloy produced by the wire-feed electron-beam additive manufacturing method. The microstructure of a 3D-printed Ti–6Al–4V alloy in the initial state, and after high-pressure torsion, was studied using optical, scanning and transmission electron microscopy. An EBSD analysis of the material in its original state was carried out. The microhardness of the material in the initial and deformed states was measured. Using the dependence of the yield strength on microhardness, the estimated mechanical strength of the material after processing by the high-pressure torsion method was determined. The microstructural features of the 3D-printed Ti–6Al–4V alloy after high-pressure torsion, which provide increased strength of this material, are discussed. The research results demonstrate that 3D printing, using the electron-beam additive manufacturing method, allows producing a Ti–6Al–4V titanium alloy with a microstructure unusual for this material, which consists of columnar primary β-grains with a transverse size of 1–2mm, inside of which martensitic α'-Ti needles are located. Thin β-Ti layers with a thickness of about 200nm are observed between the α'-Ti needles. Further deformation treatment of the alloy, using the high-pressure torsion method, allowed forming an ultrafine-grained structure in its volume, presumably consisting of α-grains with an average size of (25±10)nm. High-pressure torsion of the 3D-printed alloy allowed achieving rather high microhardness values of (448±5)НV0.1, which, according to the HV=2.8–3σy ratio, corresponds to the estimated yield strength of approximately 1460MPa.

  • Microstructural Transformation and Enhanced Strength of Wire‐Feed Electron‐Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High‐Pressure Torsion

    by Roman R. Valiev, Alexey V. Panin, Emil I. Usmanov, Yana N. Savina, Ruslan Z. Valiev

    For the first time, the present study demonstrates the influence of high‐pressure torsion (HPT) on microstructural refinement and mechanical strength of Ti–6Al–4V titanium alloy produced by wire‐feed electron‐beam additive manufacturing. This technology has attracted an increasing interest presently from manufacturers of products with complex shapes and it allows for producing a titanium alloy with a unique microstructure that consists of martensitic α′ phase, separated by thin interlayers of residual β phase. Further processing of the alloy by HPT results in the formation of an ultrafine‐grained (UFG) structure with an average grain size of about 25 ± 10 nm, significantly increasing its microhardness up to 448 ± 5 HV. Microscopic studies reveal that the attained UFG structure consists predominantly of the grains of α and β phases in the ratio of 92.8% and 7.2%, respectively. This article also considers the nature of the high strength of Ti–6Al–4V subjected to HPT.


  • Open Access

    Enhanced Erosion Resistance of an Ultrafine-Grained Ti Alloy with a PVD Coating

    by Roman R. Valiev, Konstantin S. Selivanov, Marina K. Smyslova, Yuri M. Dyblenko, Yana N. Savina, Ruslan Z. Valiev, Irina P. Semenova

    This paper presents the results of a comprehensive study of the erosive wear resistance, strength, and adhesive characteristics of the high-temperature structural titanium alloy Ti-5.7Al-3.8Mo-1.2Zr-1.3Sn (the Russian grade VT8M-1) with coarse-grained and ultrafine-grained (UFG) structures and a protective erosion-resistant TiVN coating produced by physical vapor deposition (PVD), deposited on the alloy surface. A microscopic analysis of the areas subjected to the action of abrasive particles was performed, and different characters of erosive wear were revealed depending on the structural state of the alloy. The obtained results convincingly demonstrate that by means of refining the grain structure of alloys and depositing a protective ion-plasma TiVN coating on the alloy surface, it is possible to significantly increase the erosion resistance of materials operating under high loads and in aggressive environments.


  • Enhanced service properties of a protective coating on a titanium alloy with an ultrafine-grained structure

    by R.R. Valiev, Y.M. Modina, K.S. Selivanov, I.P. Semenova, E.D. Khafizova, R.Z. Valiev, Ya.N. Savina