Dajun Tao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dajun Tao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Baojun Ge
Harbin University of Science and Technology, Harbin, China
6 shared publications - Peng Hou
National Engineering Research Center of Large Electric Machines and Heat Transfer Technology, Harbin University of Science and Technology, Harbin 150080, China
5 shared publications - Bo Pan
National Engineering Research Center of Large Electric Machines and Heat Transfer Technology, Harbin University of Science and Technology, Harbin 150080, China
3 shared publications - Yue Wang
National Engineering Research Center of Large Electric Machines and Heat Transfer Technology, Harbin University of Science and Technology, Harbin 150080, China
3 shared publications - Li-Ping Zhao
Harbin University of Science and Technology, Harbin, China
2 shared publications - Gang Hu
State key laboratory of hydro-power equipment, Harbin 150040, China
1 shared publication
Latest Publications
- 18 March 2023
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 18 (5) , 3721-3732
Model Predictive Current Control for Dual Three-Phase Permanent Magnet Synchronous Motor Based on Active Disturbance Rejection
- 18 March 2023
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 18 (5) , 3721-3732
Model Predictive Current Control for Dual Three-Phase Permanent Magnet Synchronous Motor Based on Active Disturbance Rejection
- Open Access
Analysis of Load Loss Characteristics of FeCo Alloy High Speed Permanent Magnet Motor
In order to study the change law of loss and efficiency of high-speed permanent magnet motor (HSPMM) under load after using FeCo_B800 alloy material instead of silicon steel sheet DW310_35 material to make iron core, two FeCo_B800 stator materials with the same structure and size parameters were developed. HSPMM and HSPMM of silicon steel DW310_35 stator material. The loss and efficiency characteristics of the two motors under the same operating conditions were tested by the experimental method, and the losses of the two motors at different load rates were compared and analyzed by means of the finite element method. The research results show that at light load, the FeCo_B800 motor stator core loss is lower than the DW310_35 silicon steel sheet motor, and the efficiency advantage is very obvious; however, with the increase of the load rate, the FeCo_B800 motor stator core is seriously saturated, resulting in the distortion of the winding magnetomotive force waveform. The loss caused by the harmonics of the winding magnetomotive force is higher than that of the DW310_35 silicon steel sheet motor, and the efficiency advantage of the FeCo-B800 motor gradually decreases with the increase of the load rate.
Open AccessAnalysis of Load Loss Characteristics of FeCo Alloy High Speed Permanent Magnet Motor
In order to study the change law of loss and efficiency of high-speed permanent magnet motor (HSPMM) under load after using FeCo_B800 alloy material instead of silicon steel sheet DW310_35 material to make iron core, two FeCo_B800 stator materials with the same structure and size parameters were developed. HSPMM and HSPMM of silicon steel DW310_35 stator material. The loss and efficiency characteristics of the two motors under the same operating conditions were tested by the experimental method, and the losses of the two motors at different load rates were compared and analyzed by means of the finite element method. The research results show that at light load, the FeCo_B800 motor stator core loss is lower than the DW310_35 silicon steel sheet motor, and the efficiency advantage is very obvious; however, with the increase of the load rate, the FeCo_B800 motor stator core is seriously saturated, resulting in the distortion of the winding magnetomotive force waveform. The loss caused by the harmonics of the winding magnetomotive force is higher than that of the DW310_35 silicon steel sheet motor, and the efficiency advantage of the FeCo-B800 motor gradually decreases with the increase of the load rate.
- Open Access
Research on the Influence of Power-Supply Mode and Copper-Shielding Layer on the Loss of Cryogenic Permanent Magnet Motor for LNG Pump
In order to study the method for reducing the losses in cryogenic permanent magnet motors for LNG pumps, the design of a submersible cryogenic permanent magnet brushless DC motor is presented in this paper. First, the materials used in the motor were tested at room temperature and at a low temperature, and the BH curve and BP curve of the silicon-steel sheet were obtained. Next, DC power supply and PWM power supply were used to analyze the influence of the power-supply mode on the motor loss. Finally, based on the calculation results of the motor loss, the ability of the copper-shielding layer to reduce the motor loss was explored. In the calculation process, the influence of the temperature was considered, and the motor losses at different temperatures were compared and analyzed, which provided a reference for reducing the loss of the cryogenic permanent magnet motor.
Open AccessResearch on the Influence of Power-Supply Mode and Copper-Shielding Layer on the Loss of Cryogenic Permanent Magnet Motor for LNG Pump
In order to study the method for reducing the losses in cryogenic permanent magnet motors for LNG pumps, the design of a submersible cryogenic permanent magnet brushless DC motor is presented in this paper. First, the materials used in the motor were tested at room temperature and at a low temperature, and the BH curve and BP curve of the silicon-steel sheet were obtained. Next, DC power supply and PWM power supply were used to analyze the influence of the power-supply mode on the motor loss. Finally, based on the calculation results of the motor loss, the ability of the copper-shielding layer to reduce the motor loss was explored. In the calculation process, the influence of the temperature was considered, and the motor losses at different temperatures were compared and analyzed, which provided a reference for reducing the loss of the cryogenic permanent magnet motor.
- Open Access
Rotor Strength Analysis of FeCo-Based Permanent Magnet High Speed Motor
To solve the problem of tension stress caused by centrifugal force and caused by high-speed operation of permanent magnet (PM) rotor, a FeCo-based PM rotor structure model is proposed. Based on the thick-walled cylinder theory, the uniform analytical calculation formulas of strain field, displacement field, and stress field of high-speed permanent magnet rotor are derived, and the stresses of FeCo-based PM and sleeve are obtained. The correctness of analytical calculation method (ACM) is verified by finite element method (FEM). Based on the derived analytical formula, the influence of static interference, sleeve thickness, rotating shaft, and PM thermal expansion coefficient on the strength of high-speed permanent magnet rotor is analyzed, and the mechanical design law of high-speed permanent magnet rotor is summarized. Alloy sleeves are usually fitted outside the high-speed permanent magnet rotor to protect the PM from damage. In order to ensure safe operation of PM rotor under hot rotating conditions, strength calculation and check of sleeve and PM must be carried out. Based on the characteristics of slender structure of high-speed rotor, a high-speed permanent magnet motor (HSPMM) with a rated power of 100 kW and a rated speed of 18,000 r/min was produced, and a continuous operation test was carried out to verify the validity of the above theoretical analysis.
Open AccessRotor Strength Analysis of FeCo-Based Permanent Magnet High Speed Motor
To solve the problem of tension stress caused by centrifugal force and caused by high-speed operation of permanent magnet (PM) rotor, a FeCo-based PM rotor structure model is proposed. Based on the thick-walled cylinder theory, the uniform analytical calculation formulas of strain field, displacement field, and stress field of high-speed permanent magnet rotor are derived, and the stresses of FeCo-based PM and sleeve are obtained. The correctness of analytical calculation method (ACM) is verified by finite element method (FEM). Based on the derived analytical formula, the influence of static interference, sleeve thickness, rotating shaft, and PM thermal expansion coefficient on the strength of high-speed permanent magnet rotor is analyzed, and the mechanical design law of high-speed permanent magnet rotor is summarized. Alloy sleeves are usually fitted outside the high-speed permanent magnet rotor to protect the PM from damage. In order to ensure safe operation of PM rotor under hot rotating conditions, strength calculation and check of sleeve and PM must be carried out. Based on the characteristics of slender structure of high-speed rotor, a high-speed permanent magnet motor (HSPMM) with a rated power of 100 kW and a rated speed of 18,000 r/min was produced, and a continuous operation test was carried out to verify the validity of the above theoretical analysis.
- Open Access
Fault-Tolerant Control for Reducing Harmonic Distortion of Dual Three-Phase Permanent Magnet Synchronous Motor
Aiming at the open circuit fault of a dual three-phase permanent magnet synchronous motor, a normalized current method is used for open circuit fault diagnosis. Then, a fault-tolerant control strategy for reducing the harmonic distortion of a dual three-phase permanent magnet synchronous motor is proposed, which is based on current model prediction control and keeps the decoupling transformation matrix unchanged. The fault-tolerant control method based on current model prediction considers the influence of the control quantity on the future state of the system, and effectively reduces the total harmonic distortion. Two fault-tolerant control strategies for the motor are analyzed, with minimizing stator copper consumption and maximizing torque output as control objectives. Through simulation and experiment of fault-tolerant control strategies for a dual three-phase permanent magnet synchronous motor, the results verify the effectiveness and feasibility of the strategy.
Open AccessFault-Tolerant Control for Reducing Harmonic Distortion of Dual Three-Phase Permanent Magnet Synchronous Motor
Aiming at the open circuit fault of a dual three-phase permanent magnet synchronous motor, a normalized current method is used for open circuit fault diagnosis. Then, a fault-tolerant control strategy for reducing the harmonic distortion of a dual three-phase permanent magnet synchronous motor is proposed, which is based on current model prediction control and keeps the decoupling transformation matrix unchanged. The fault-tolerant control method based on current model prediction considers the influence of the control quantity on the future state of the system, and effectively reduces the total harmonic distortion. Two fault-tolerant control strategies for the motor are analyzed, with minimizing stator copper consumption and maximizing torque output as control objectives. Through simulation and experiment of fault-tolerant control strategies for a dual three-phase permanent magnet synchronous motor, the results verify the effectiveness and feasibility of the strategy.
- Open Access
Coupling Analysis of Electromagnetic Vibration and Noise of FeCo-Based Permanent-Magnet Synchronous Motor
Addressing the problem of the vibration and noise of a permanent-magnet synchronous motor (PMSM), this paper optimizes the structure of a permanent-magnet motor rotator, introduces the electromagnetic-structure-acoustic coupling calculation model, and optimizes the motor rotator to reduce the vibration and noise of a permanent-magnet motor. Using the theory of Maxwell’s stress equation, the radial electromagnetic force on the stator teeth of the permanent-magnet motor is deduced and analyzed, and the correctness of the analysis calculation is verified by using the finite element multi-physical field coupling method. Based on the deduced analytical expression of the radial electromagnetic force, the sources of the radial electromagnetic force for each order and the frequency of the permanent-magnet motor are summarized. A 12-slot, 8-pole, permanent-magnet motor is taken as an example. A calculation model considering the spatial distribution of the radial electromagnetic force and the electromagnetic vibration of an iron-cobalt-based stator is established. The harmonic response of the electromagnetic vibration of the motor is analyzed, and a modal analysis is carried out. The optimized acceleration vibration noise cascade of the FeCo-based permanent-magnet drive motor under load is given. The correctness and validity of the theoretical derivation and simulation are verified by experiments.
Open AccessCoupling Analysis of Electromagnetic Vibration and Noise of FeCo-Based Permanent-Magnet Synchronous Motor
Addressing the problem of the vibration and noise of a permanent-magnet synchronous motor (PMSM), this paper optimizes the structure of a permanent-magnet motor rotator, introduces the electromagnetic-structure-acoustic coupling calculation model, and optimizes the motor rotator to reduce the vibration and noise of a permanent-magnet motor. Using the theory of Maxwell’s stress equation, the radial electromagnetic force on the stator teeth of the permanent-magnet motor is deduced and analyzed, and the correctness of the analysis calculation is verified by using the finite element multi-physical field coupling method. Based on the deduced analytical expression of the radial electromagnetic force, the sources of the radial electromagnetic force for each order and the frequency of the permanent-magnet motor are summarized. A 12-slot, 8-pole, permanent-magnet motor is taken as an example. A calculation model considering the spatial distribution of the radial electromagnetic force and the electromagnetic vibration of an iron-cobalt-based stator is established. The harmonic response of the electromagnetic vibration of the motor is analyzed, and a modal analysis is carried out. The optimized acceleration vibration noise cascade of the FeCo-based permanent-magnet drive motor under load is given. The correctness and validity of the theoretical derivation and simulation are verified by experiments.
- Open Access
Analysis of Eddy Current Loss of 120-kW High-Speed Permanent Magnet Synchronous Motor
Pulse width modulation current harmonics and space harmonics are some of the major factors affecting the rotor eddy current loss of the high-speed permanent magnet motor. In this study, based on the principle of the equivalent current sheet, a two-dimensional motor model in a rectangular coordinate system was established. Considering the armature reaction, the end effect, and the current harmonics generated by variable frequency power supply, the eddy current loss of the rotor at different frequencies was analyzed and calculated using the analytical and finite element methods (FEM). When the frequency is between 200 Hz and 600 Hz, the variation trend of the rotor eddy current loss with a frequency obtained by analytical calculation and FEM analysis is roughly the same, and the error is still within a reasonable range. However, as the frequency continues to increase, the error between the two becomes larger and larger. Furthermore, based on the two-dimensional FE model, the influence of the sleeve material, the thickness, and the composite structure on the rotor eddy current loss were studied and analyzed. It was found that adding a graphene shielding layer between the permanent magnet and the sleeve can effectively shield the harmonic magnetic field, greatly reduce the eddy current loss of the permanent magnet, and effectively prevent the temperature of the permanent magnet from being too high, which is conducive to the continuous and stable operation of the high-speed permanent magnet motor.
Open AccessAnalysis of Eddy Current Loss of 120-kW High-Speed Permanent Magnet Synchronous Motor
Pulse width modulation current harmonics and space harmonics are some of the major factors affecting the rotor eddy current loss of the high-speed permanent magnet motor. In this study, based on the principle of the equivalent current sheet, a two-dimensional motor model in a rectangular coordinate system was established. Considering the armature reaction, the end effect, and the current harmonics generated by variable frequency power supply, the eddy current loss of the rotor at different frequencies was analyzed and calculated using the analytical and finite element methods (FEM). When the frequency is between 200 Hz and 600 Hz, the variation trend of the rotor eddy current loss with a frequency obtained by analytical calculation and FEM analysis is roughly the same, and the error is still within a reasonable range. However, as the frequency continues to increase, the error between the two becomes larger and larger. Furthermore, based on the two-dimensional FE model, the influence of the sleeve material, the thickness, and the composite structure on the rotor eddy current loss were studied and analyzed. It was found that adding a graphene shielding layer between the permanent magnet and the sleeve can effectively shield the harmonic magnetic field, greatly reduce the eddy current loss of the permanent magnet, and effectively prevent the temperature of the permanent magnet from being too high, which is conducive to the continuous and stable operation of the high-speed permanent magnet motor.