Alexandru Andrei Vasile
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexandru Andrei Vasile has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Nasser Mohieddin Abukhdeir
Department of Chemical Engineering, University of Waterloo, Waterloo, Ontario, Canada
5 shared publications Hector Budman
2 shared publications- Marc Gordon Aucoin
Department of Chemical Engineering, University of Waterloo, Waterloo, ON N2L 3G1, Canada
2 shared publications - Daham Diyanath Liyanage1 shared publication
- Elizabeth Julia Monte1 shared publication
- Jake E. Ferguson1 shared publication
Latest Publications
- Open Access
- 16 August 2026
- Published by Elsevier in SSRN Electronic Journal
Automata-Based Simulation Framework for Modeling Pool Boiling
An improved stochastic automata model is developed based on the model developed by Marcel and coworkers (C. Marcel et al., Int. J. Heat Mass Trans. 111 (2017) 657-665). The model utilizes active nucleation site density correlations to determine the number of nucleation sites per time step, eliminating the need for fitted parameters in the cavity size distribution used for determining active nucleation sites. The model includes random nucleation site distribution, geometrically consistent bubble growth, micro-layer evaporation, and micro-convection heat transfer models with the effect of surface wettability. The model is validated against a broad set of experimental data from the literature with diverse surface characteristics including wettability and surface roughness. The transition from isolated bubble departure to coalesced bubble departure regimes is identified from experimental data and compared to model predictions. The validation study shows that the presented model shows good agreement for wall superheat in the isolated bubble region, with the mean absolute percentage error (MAPE) between 6.64% and 7.46%. With the enhanced stochastic automata model presented in this work, the effect of wettability, surface roughness, and heater material properties can be clearly identified within the isolated bubble formation/departure boiling regime. The results presented in this work quantitatively show that the presented boiling model enables improved physical fidelity and computational efficiency for pool boiling processes.
- 16 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAutomata-Based Simulation Framework for Modeling Pool Boiling
An improved stochastic automata model is developed based on the model developed by Marcel and coworkers (C. Marcel et al., Int. J. Heat Mass Trans. 111 (2017) 657-665). The model utilizes active nucleation site density correlations to determine the number of nucleation sites per time step, eliminating the need for fitted parameters in the cavity size distribution used for determining active nucleation sites. The model includes random nucleation site distribution, geometrically consistent bubble growth, micro-layer evaporation, and micro-convection heat transfer models with the effect of surface wettability. The model is validated against a broad set of experimental data from the literature with diverse surface characteristics including wettability and surface roughness. The transition from isolated bubble departure to coalesced bubble departure regimes is identified from experimental data and compared to model predictions. The validation study shows that the presented model shows good agreement for wall superheat in the isolated bubble region, with the mean absolute percentage error (MAPE) between 6.64% and 7.46%. With the enhanced stochastic automata model presented in this work, the effect of wettability, surface roughness, and heater material properties can be clearly identified within the isolated bubble formation/departure boiling regime. The results presented in this work quantitatively show that the presented boiling model enables improved physical fidelity and computational efficiency for pool boiling processes.
- Open Access
- 17 June 2026
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 231, 744-759
Flow alignment-informed method for compartmental modelling of multiphase flows
- 17 June 2026
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 231, 744-759
Open AccessFlow alignment-informed method for compartmental modelling of multiphase flows
- Open Access
- 30 October 2024
- Published by The Open Journal in Journal of Open Source Software
- Vol. 9 (102) , 6963
OpenCCM: An Open-Source Continuous Compartmental Modelling Package
OpenCCM is a compartmental modelling (Jourdan et al., 2019) software package based on recently developed fully automated flow alignment compartmentalization methods (Vasile et al., 2024). It is primarily intended for large-scale flow-based processes with weak coupling between composition changes, e.g., through (bio)chemical reactions, and convective mass transport in the system. Compartmental modelling is an important approach used to develop reduced-order models (Benner et al., 2020; Chinesta et al., 2017) using a priori knowledge of process hydrodynamics (Jourdan et al., 2019). Compartmental modelling methods, such as those implemented in OpenCCM, enable simulations of these processes with far less computational complexity while still capturing the key aspects of process dynamics. OpenCCM integrates with two multiphysics simulation software packages, OpenCMP (Monte et al., 2022) and OpenFOAM (Greenshields, 2024), allowing for ease of transferring simulation data for compartmentalization. Additionally, it provides users with built-in functionality for computing residence times and exporting for use in other simulation or visualization software, including ParaView (Ayachit, 2015). Post-processing methods are included for mapping simulation results from compartment domains to the original simulation domain, which are useful for visualization purposes and for further simulations in using other software (e.g., multi-scale modelling).
- 30 October 2024
- Published by The Open Journal in Journal of Open Source Software
- Vol. 9 (102) , 6963
Open AccessOpenCCM: An Open-Source Continuous Compartmental Modelling Package
OpenCCM is a compartmental modelling (Jourdan et al., 2019) software package based on recently developed fully automated flow alignment compartmentalization methods (Vasile et al., 2024). It is primarily intended for large-scale flow-based processes with weak coupling between composition changes, e.g., through (bio)chemical reactions, and convective mass transport in the system. Compartmental modelling is an important approach used to develop reduced-order models (Benner et al., 2020; Chinesta et al., 2017) using a priori knowledge of process hydrodynamics (Jourdan et al., 2019). Compartmental modelling methods, such as those implemented in OpenCCM, enable simulations of these processes with far less computational complexity while still capturing the key aspects of process dynamics. OpenCCM integrates with two multiphysics simulation software packages, OpenCMP (Monte et al., 2022) and OpenFOAM (Greenshields, 2024), allowing for ease of transferring simulation data for compartmentalization. Additionally, it provides users with built-in functionality for computing residence times and exporting for use in other simulation or visualization software, including ParaView (Ayachit, 2015). Post-processing methods are included for mapping simulation results from compartment domains to the original simulation domain, which are useful for visualization purposes and for further simulations in using other software (e.g., multi-scale modelling).
- Open Access
- 16 March 2024
- Published by Elsevier in Computers & Chemical Engineering
- Vol. 185
A flow alignment-informed method for compartmental modelling
- 16 March 2024
- Published by Elsevier in Computers & Chemical Engineering
- Vol. 185
Open AccessA flow alignment-informed method for compartmental modelling
- Open Access
- 6 May 2022
- Published by The Open Journal in Journal of Open Source Software
- Vol. 7 (73) , 3742
OpenCMP: An Open-Source Computational Multiphysics Package
- 6 May 2022
- Published by The Open Journal in Journal of Open Source Software
- Vol. 7 (73) , 3742
Open AccessOpenCMP: An Open-Source Computational Multiphysics Package