Omer Yunus Gumus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Omer Yunus Gumus has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Halil Ibrahim Unal
Gazi University
2 shared publications - Israfil Kucuk
Institute of Nanotechnology, Gebze Technical University, Kocaeli 41400, Turkey
2 shared publications - Kamil Feratoğlu
Kirklareli University
2 shared publications Ahmet Celik
Faculty of Arts and Sciences, Department of Physics, Giresun University, Giresun, Türkiye
1 shared publication- Ayse Celik Bedeloglu
Bursa Technical University
1 shared publication Berat Enes Canli
Department of Polymer Materials Engineering, Engineering and Natural Sciences Faculty, Bursa Technical University, Bursa, Turkey
1 shared publication
Latest Publications
- 22 October 2026
- Published by Turkish Journal of Forestry in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
- Vol. 27, 265-278
Characterization of PLA–hemp biocomposites produced by hot-pressing
This study investigates the thermal, chemical, physical, morphological, and mechanical properties of hot-pressed PLA-hemp biocomposites produced without compatibilizers. Hemp particles below 75 µm were composed of PLA at 3%, 6%, and 9 wt%, and neat PLA was evaluated in both granular and extruded forms. The composition was compounded using a twin-screw extruder and converted into plates by hot pressing. TGA showed that extrusion slightly improved the thermal stability of neat PLA, whereas hemp addition reduced degradation temperatures. DSC results demonstrated that hemp fibers increased earlier crystallization and the crystallinity of the PLA matrix. FTIR spectra showed that the interaction between PLA and hemp was mainly physical but there is no evidence of new chemical bond formation. Water absorption and thickness swelling increased with hemp content, reaching the highest values in PLA-H9. Surface roughness was significantly affected by sample type, while tensile and flexural strengths decreased after hemp incorporation. SEM images depicted fiber pull-out, interfacial debonding, and micro voids, confirming limited matrix–fiber adhesion. Overall, hemp addition improved bio-based content but reduced strength without compatibilization.
- 22 October 2026
- Published by Turkish Journal of Forestry in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
- Vol. 27, 265-278
Characterization of PLA–hemp biocomposites produced by hot-pressing
This study investigates the thermal, chemical, physical, morphological, and mechanical properties of hot-pressed PLA-hemp biocomposites produced without compatibilizers. Hemp particles below 75 µm were composed of PLA at 3%, 6%, and 9 wt%, and neat PLA was evaluated in both granular and extruded forms. The composition was compounded using a twin-screw extruder and converted into plates by hot pressing. TGA showed that extrusion slightly improved the thermal stability of neat PLA, whereas hemp addition reduced degradation temperatures. DSC results demonstrated that hemp fibers increased earlier crystallization and the crystallinity of the PLA matrix. FTIR spectra showed that the interaction between PLA and hemp was mainly physical but there is no evidence of new chemical bond formation. Water absorption and thickness swelling increased with hemp content, reaching the highest values in PLA-H9. Surface roughness was significantly affected by sample type, while tensile and flexural strengths decreased after hemp incorporation. SEM images depicted fiber pull-out, interfacial debonding, and micro voids, confirming limited matrix–fiber adhesion. Overall, hemp addition improved bio-based content but reduced strength without compatibilization.
- 24 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11539-11573
Additive manufacturing of vulcanized EPDM/carbon black rubber composites by solvent-cast 3D printing: production of a repeatable and sensitive piezoresistive strain sensor for wearable applications
- 24 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11539-11573
Additive manufacturing of vulcanized EPDM/carbon black rubber composites by solvent-cast 3D printing: production of a repeatable and sensitive piezoresistive strain sensor for wearable applications
- 23 May 2026
- Published by Springer Nature in Chemistry Africa
- Vol. 9 (5) , 194
Influence of Amines on the Structure and Adsorption Properties of PVA Hydrogels for Dye Removal
- 23 May 2026
- Published by Springer Nature in Chemistry Africa
- Vol. 9 (5) , 194
Influence of Amines on the Structure and Adsorption Properties of PVA Hydrogels for Dye Removal
- Open Access
- 22 February 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (17) , 1-21
Development and Characterization of Polyethylene Naphthalate (PEN)/Tungsten Oxide (WO3) Composites for Gamma Radiation Shielding Applications
The present study details the design and integral characterization of a novel polyethylene naphthalate (PEN)/tungsten oxide (WO 3 ) composite designed for gamma radiation shielding applications. The composites were prepared by melt processing, incorporating WO 3 at 5, 10, and 20% by mass as a high-Z filler to enhance the radiation attenuation efficiency. We performed morphological, structural, and thermal characterizations of these composites using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). Additionally, the tensile test was performed to evaluate the mechanical strength. The shielding performance was evaluated by determining the mass attenuation coefficient (MAC, µ m ), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP) across photon energies ranging from 31 to 1332 keV. These parameters were determined experimentally using the HPGe gamma detector and the NIST XCOM database, and were theoretically simulated using the EGS4 Monte Carlo approach. A strong agreement was found between the experimental, simulation, and theoretical attenuation values, confirming the effectiveness of the composite in gamma radiation shielding. The MAC value of the pure PEN, which was 0.080 cm 2 /g at 662 keV, was increased to 0.086 cm 2 /g by introducing 20 wt% of WO 3 . The results indicate the potential of PEN/WO 3 composites as lightweight, efficient shielding materials for radiation protection applications, particularly in the 31–276 keV energy range.
- 22 February 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (17) , 1-21
Open AccessDevelopment and Characterization of Polyethylene Naphthalate (PEN)/Tungsten Oxide (WO3) Composites for Gamma Radiation Shielding Applications
The present study details the design and integral characterization of a novel polyethylene naphthalate (PEN)/tungsten oxide (WO 3 ) composite designed for gamma radiation shielding applications. The composites were prepared by melt processing, incorporating WO 3 at 5, 10, and 20% by mass as a high-Z filler to enhance the radiation attenuation efficiency. We performed morphological, structural, and thermal characterizations of these composites using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). Additionally, the tensile test was performed to evaluate the mechanical strength. The shielding performance was evaluated by determining the mass attenuation coefficient (MAC, µ m ), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP) across photon energies ranging from 31 to 1332 keV. These parameters were determined experimentally using the HPGe gamma detector and the NIST XCOM database, and were theoretically simulated using the EGS4 Monte Carlo approach. A strong agreement was found between the experimental, simulation, and theoretical attenuation values, confirming the effectiveness of the composite in gamma radiation shielding. The MAC value of the pure PEN, which was 0.080 cm 2 /g at 662 keV, was increased to 0.086 cm 2 /g by introducing 20 wt% of WO 3 . The results indicate the potential of PEN/WO 3 composites as lightweight, efficient shielding materials for radiation protection applications, particularly in the 31–276 keV energy range.
- Open Access
- 29 March 2024
- Published by Bursa Technical University in Journal of Innovative Science and Engineering
- Vol. 8 (1) , 103-114
Redox Properties of Poly (aniline boronic acid) in Aqueous Environment with Glucose and Table Sugar Addition
Polyaniline boronic acid, a conducting polymer with unique properties, has gained attention for its potential applications in batteries, sensors, drug delivery systems, and electrochemical devices. Understanding the redox behavior of this polymer in the presence of sugars is of particular interest due to the potential implications for its functionality in various applications. Cyclic voltammetry is employed to analyze the redox behavior of the polymer in aqueous solutions with glucose and table sugar. Preliminary results suggest that the presence of glucose improves, and table sugar declines the peak values. The diffusion coefficient of the polymer is found as 2.6x10-9 cm2/s. The choice of supporting electrolyte, exemplified by potassium carbonate and potassium chloride, also exhibited an influence on redox behavior of polyaniline boronic acid, and peak potential and peak values are higher in potassium chloride solutions.
- 29 March 2024
- Published by Bursa Technical University in Journal of Innovative Science and Engineering
- Vol. 8 (1) , 103-114
Open AccessRedox Properties of Poly (aniline boronic acid) in Aqueous Environment with Glucose and Table Sugar Addition
Polyaniline boronic acid, a conducting polymer with unique properties, has gained attention for its potential applications in batteries, sensors, drug delivery systems, and electrochemical devices. Understanding the redox behavior of this polymer in the presence of sugars is of particular interest due to the potential implications for its functionality in various applications. Cyclic voltammetry is employed to analyze the redox behavior of the polymer in aqueous solutions with glucose and table sugar. Preliminary results suggest that the presence of glucose improves, and table sugar declines the peak values. The diffusion coefficient of the polymer is found as 2.6x10-9 cm2/s. The choice of supporting electrolyte, exemplified by potassium carbonate and potassium chloride, also exhibited an influence on redox behavior of polyaniline boronic acid, and peak potential and peak values are higher in potassium chloride solutions.
- Open Access
- 13 March 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (11) , 14927-14948
Effect of Carbon Nanotube Reinforcement on Creep and Recovery Behavior of Additively Manufactured Polymers: An Experimental and Prediction Study
In this study, one of the most frequently used polymeric materials in fused deposition modeling (FDM) acrylonitrile butadiene styrene (ABS) is reinforced with different amount of carbon nanotubes (CNTs). Thermogravimetric analysis and differential scanning calorimetry analysis are applied to examine thermal degradation behavior of produced nanocomposite filaments. Specimens are manufactured by fused deposition modeling by using produced nanocomposite filaments. Tensile, creep and viscoelastic-viscoplastic behaviors of FDM-printed nanocomposite samples are investigated by conducting tensile, creep and loading–unloading tests under different strain rates and strain levels. Morphology of 3D printed samples is examined through scanning electron microscopy. Void densities which plays important role in mechanical behavior of additively manufactured samples are determined via ImageJ and CNT reinforcement on void densities are investigated. Data obtained from tests are used in system identification process, and multi-input–single-output model structures are proposed for the prediction of tensile, creep and recovery behaviors of 3D printed nanocomposite materials.
- 13 March 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (11) , 14927-14948
Open AccessEffect of Carbon Nanotube Reinforcement on Creep and Recovery Behavior of Additively Manufactured Polymers: An Experimental and Prediction Study
In this study, one of the most frequently used polymeric materials in fused deposition modeling (FDM) acrylonitrile butadiene styrene (ABS) is reinforced with different amount of carbon nanotubes (CNTs). Thermogravimetric analysis and differential scanning calorimetry analysis are applied to examine thermal degradation behavior of produced nanocomposite filaments. Specimens are manufactured by fused deposition modeling by using produced nanocomposite filaments. Tensile, creep and viscoelastic-viscoplastic behaviors of FDM-printed nanocomposite samples are investigated by conducting tensile, creep and loading–unloading tests under different strain rates and strain levels. Morphology of 3D printed samples is examined through scanning electron microscopy. Void densities which plays important role in mechanical behavior of additively manufactured samples are determined via ImageJ and CNT reinforcement on void densities are investigated. Data obtained from tests are used in system identification process, and multi-input–single-output model structures are proposed for the prediction of tensile, creep and recovery behaviors of 3D printed nanocomposite materials.
- Open Access
- 9 November 2023
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 30 (2) , 543-556
Mechanical, UV protection, and antibacterial properties of poly(vinyl alcohol) /marine mucilage biocomposite films
The mucilage that accumulated in the Sea of Marmara in 2021 turned into an environmental disaster that threatened not only marine life but also the shipping and tourism industries. However, because of the partially organic structure of marine mucilage, it has the potential to be used as an additive for polymer films. In this study, bioplastic films were prepared from PVA with a series of mucilage content from 0% to 50% by mass, and their properties were investigated. The FT‐IR spectra revealed a shift in hydroxyl peaks, suggesting an interaction between the mucilage and PVA. SEM images showed the formation of crystal forms at the higher mucilage content of 20%, indicating ionic saturation of the PVA matrix. EDX and XRD analyses revealed that the crystal was NaCl coming from the mucilage composition. The tensile strength of the neat PVA film was measured as 9.86 MPa and improved to 14.56 MPa with 5% mucilage content, which is attributed to the ionic cross‐linking. The tensile properties were preserved up to 20% of the mucilage content, and then sudden decrements were observed. The transmittance percentage ( T %) of the neat PVA film in UV–Vis spectra (800–200 nm) was detected as 75% at 500 nm and decreased down to 39% with increased mucilage content up to 50%. Furthermore, a rising limit of linearity (LOL) of the spectrums was observed from 350 to 580 nm, with increasing mucilage content from 5% to 50%. The biofilms showed antibacterial activity against Escherichia coli and Staphylococcus aureus bacteria. Hence, a robust and biodegradable film having UV protection and antibacterial activity was developed from the marine mucilage bio‐waste. Highlights: Poly(vinyl alcohol)/marine mucilage biocomposite films were prepared. Biocomposite films showed increased UV‐A, UV‐B, and UV‐C protection with increased mucilage content. Enhanced tensile strength of biocomposite films up to 20 wt% mucilage content was determined due to ionic crosslink formed by NaCl salt ions. Biocomposite exhibited antibacterial activity against Escherichia coli and Staphylococcus aureus .
- 9 November 2023
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 30 (2) , 543-556
Open AccessMechanical, UV protection, and antibacterial properties of poly(vinyl alcohol) /marine mucilage biocomposite films
The mucilage that accumulated in the Sea of Marmara in 2021 turned into an environmental disaster that threatened not only marine life but also the shipping and tourism industries. However, because of the partially organic structure of marine mucilage, it has the potential to be used as an additive for polymer films. In this study, bioplastic films were prepared from PVA with a series of mucilage content from 0% to 50% by mass, and their properties were investigated. The FT‐IR spectra revealed a shift in hydroxyl peaks, suggesting an interaction between the mucilage and PVA. SEM images showed the formation of crystal forms at the higher mucilage content of 20%, indicating ionic saturation of the PVA matrix. EDX and XRD analyses revealed that the crystal was NaCl coming from the mucilage composition. The tensile strength of the neat PVA film was measured as 9.86 MPa and improved to 14.56 MPa with 5% mucilage content, which is attributed to the ionic cross‐linking. The tensile properties were preserved up to 20% of the mucilage content, and then sudden decrements were observed. The transmittance percentage ( T %) of the neat PVA film in UV–Vis spectra (800–200 nm) was detected as 75% at 500 nm and decreased down to 39% with increased mucilage content up to 50%. Furthermore, a rising limit of linearity (LOL) of the spectrums was observed from 350 to 580 nm, with increasing mucilage content from 5% to 50%. The biofilms showed antibacterial activity against Escherichia coli and Staphylococcus aureus bacteria. Hence, a robust and biodegradable film having UV protection and antibacterial activity was developed from the marine mucilage bio‐waste. Highlights: Poly(vinyl alcohol)/marine mucilage biocomposite films were prepared. Biocomposite films showed increased UV‐A, UV‐B, and UV‐C protection with increased mucilage content. Enhanced tensile strength of biocomposite films up to 20 wt% mucilage content was determined due to ionic crosslink formed by NaCl salt ions. Biocomposite exhibited antibacterial activity against Escherichia coli and Staphylococcus aureus .
- 20 March 2023
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (5) , 653-676
Enhanced strength and toughness of polylactic acid by blending with modified natural rubber having acetate pendant group
Among biobased and biodegradable polymers, polylactic acid (PLA) is most widely used one. However, its poor mechanical properties need to be enhanced. In this study, PLA blend film with improved mechanical properties were developed without compromising any bio-content. For this, natural rubber derivative with acetate pendant group (ANR) and PLA blend films were prepared. First, natural rubber was epoxidized, and then partial acetylation was achieved by the ring-opening reaction of the epoxy groups. The epoxidation and the acetylation were examined by FTIR analysis. 1H-NMR spectrum revealed a 29% epoxidation and 8.25% acetylation degree. The Tg of natural rubber (−66°C) increased to −41°C and −31°C after epoxidation and acetylation, respectively. The compatibility of ENR and ANR with PLA was evident from the DSC results and Molau test. The morphology of PLA blend film containing 25 wt% of ANR (ANR25) was observed as well-dispersed fine droplets by SEM images. The tensile strength, elastic modulus, and yield strength of ANR25 were measured as 11.6 MPa, 397.3 MPa, and 6.9 MPa, respectively. These values are considerably higher than neat PLA film. Compared to reported studies on PLA toughening so far, increments in both the strength and elongation of ANR25 were observed by tensile tests. Moreover, highest toughness among all samples was determined as 18.8 MJm−3 for ANR25, which is 1.8 times higher than neat PLA. Thus, a strong and tough bio-based PLA blend was developed for film application such as packaging and sheeting.
- 20 March 2023
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (5) , 653-676
Enhanced strength and toughness of polylactic acid by blending with modified natural rubber having acetate pendant group
Among biobased and biodegradable polymers, polylactic acid (PLA) is most widely used one. However, its poor mechanical properties need to be enhanced. In this study, PLA blend film with improved mechanical properties were developed without compromising any bio-content. For this, natural rubber derivative with acetate pendant group (ANR) and PLA blend films were prepared. First, natural rubber was epoxidized, and then partial acetylation was achieved by the ring-opening reaction of the epoxy groups. The epoxidation and the acetylation were examined by FTIR analysis. 1H-NMR spectrum revealed a 29% epoxidation and 8.25% acetylation degree. The Tg of natural rubber (−66°C) increased to −41°C and −31°C after epoxidation and acetylation, respectively. The compatibility of ENR and ANR with PLA was evident from the DSC results and Molau test. The morphology of PLA blend film containing 25 wt% of ANR (ANR25) was observed as well-dispersed fine droplets by SEM images. The tensile strength, elastic modulus, and yield strength of ANR25 were measured as 11.6 MPa, 397.3 MPa, and 6.9 MPa, respectively. These values are considerably higher than neat PLA film. Compared to reported studies on PLA toughening so far, increments in both the strength and elongation of ANR25 were observed by tensile tests. Moreover, highest toughness among all samples was determined as 18.8 MJm−3 for ANR25, which is 1.8 times higher than neat PLA. Thus, a strong and tough bio-based PLA blend was developed for film application such as packaging and sheeting.
- 17 March 2023
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 43 (4) , 318-332
Wear prediction of 3D-printed acrylonitrile butadiene styrene-carbon nanotube nanocomposites at elevated temperatures
In this study, multi-wall carbon nanotube (MWCNT) reinforced acrylonitrile butadiene styrene (ABS) nanocomposite filaments are produced. Filaments are examined through thermogravimetric analysis (TGA) and definitive scanning calorimetry (DSC) analysis. Produced nanocomposite filaments are used in the fused deposition modeling (FDM) process to manufacture parts. Wear tests are conducted on 3D-printed parts using wear test apparatus with an attached heating module under different ambient temperatures. Hence, the influence of CNT reinforcement, along with different FDM process parameters and varying test conditions on the wear behavior of 3D-printed ABS-CNT parts, are examined. Worn surfaces of the specimens are examined by scanning electron microscopy (SEM). Nonlinear autoregressive exogenous (NARX) models are proposed for the prediction of the wear behavior of 3D-printed ABS-CNT nanocomposites. While wear rate is taken as output, ambient temperature and amount of nanofiller are accounted as input parameters along with the variation of coefficient of friction (COF) which is obtained from measured frictional force and three input-one output model structure is proposed for NARX. The use of multiple input-single output (MISO) model structure and examining the wear behavior of 3D-printed ABS-CNT samples under different wear test conditions with different FDM process parameters are the novelties in this work.
- 17 March 2023
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 43 (4) , 318-332
Wear prediction of 3D-printed acrylonitrile butadiene styrene-carbon nanotube nanocomposites at elevated temperatures
In this study, multi-wall carbon nanotube (MWCNT) reinforced acrylonitrile butadiene styrene (ABS) nanocomposite filaments are produced. Filaments are examined through thermogravimetric analysis (TGA) and definitive scanning calorimetry (DSC) analysis. Produced nanocomposite filaments are used in the fused deposition modeling (FDM) process to manufacture parts. Wear tests are conducted on 3D-printed parts using wear test apparatus with an attached heating module under different ambient temperatures. Hence, the influence of CNT reinforcement, along with different FDM process parameters and varying test conditions on the wear behavior of 3D-printed ABS-CNT parts, are examined. Worn surfaces of the specimens are examined by scanning electron microscopy (SEM). Nonlinear autoregressive exogenous (NARX) models are proposed for the prediction of the wear behavior of 3D-printed ABS-CNT nanocomposites. While wear rate is taken as output, ambient temperature and amount of nanofiller are accounted as input parameters along with the variation of coefficient of friction (COF) which is obtained from measured frictional force and three input-one output model structure is proposed for NARX. The use of multiple input-single output (MISO) model structure and examining the wear behavior of 3D-printed ABS-CNT samples under different wear test conditions with different FDM process parameters are the novelties in this work.