Dar-Yuan Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Dar-Yuan Chang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Chien-Hung Lin
1 shared publication- Chien-Hung Lin
Department of Mechanical Engineering, Chinese Culture University, Taipei, Taiwan (R.O.C.)
1 shared publication Chun-Chun Yang
Master Program in Department of Mechanical Engineering, Chinese Culture University, Taipei, Taiwan (R.O.C.)
1 shared publicationHsiang-Cheng Chien
1 shared publicationShan-Chao Chou
Department of Mechanical Engineering, Chinese Culture University, Taipei, Taiwan (R.O.C.)
1 shared publicationXing-Yao Wu
Department of Mechanical Engineering, Chinese Culture University, Taipei, Taiwan (R.O.C.)
1 shared publication
Latest Publications
- Open Access
- 11 May 2022
- Published by Springer Nature in Research Square
Parameters for drilling a stepped microhole of nitride ceramics using Taguchi-based grey relational analysis method
Microdrilling is an essential process in the semiconductor industry to produce microholes for wafer testing instruments such as a wafer probe card. The microholes are laid on an insulating ceramic plate in an array form for piloting microprobes to their specified positions, which are commonly machined by a peck-drilling process. This study investigated the parameters of cutting speed, feed rate, and depth in the peck-drilling process for making a stepped microhole of nitride ceramic plates. A two-level microdrilling experiment was first carried out to investigate the thrust force in drilling a 310-µm-diameter through microhole for checking the interactivity between the drilling parameters. After clarifying parametric interactions, Taguchi’s three-level fractional-factorial experiment of a stepped microhole was performed to derive “preferred factorial level set” for minimizing the thrust force and improving hole characteristics. Furthermore, Grey Relational Analysis (GRA) model was built to infer “optimal parameters level design” for considering the multi-characteristic problem of the microhole drilled. Experimental validations were implemented to confirm the analytical results. Experimental data provide useful references for drilling a stepped microhole of nitride ceramic plates.
- 11 May 2022
- Published by Springer Nature in Research Square
Open AccessParameters for drilling a stepped microhole of nitride ceramics using Taguchi-based grey relational analysis method
Microdrilling is an essential process in the semiconductor industry to produce microholes for wafer testing instruments such as a wafer probe card. The microholes are laid on an insulating ceramic plate in an array form for piloting microprobes to their specified positions, which are commonly machined by a peck-drilling process. This study investigated the parameters of cutting speed, feed rate, and depth in the peck-drilling process for making a stepped microhole of nitride ceramic plates. A two-level microdrilling experiment was first carried out to investigate the thrust force in drilling a 310-µm-diameter through microhole for checking the interactivity between the drilling parameters. After clarifying parametric interactions, Taguchi’s three-level fractional-factorial experiment of a stepped microhole was performed to derive “preferred factorial level set” for minimizing the thrust force and improving hole characteristics. Furthermore, Grey Relational Analysis (GRA) model was built to infer “optimal parameters level design” for considering the multi-characteristic problem of the microhole drilled. Experimental validations were implemented to confirm the analytical results. Experimental data provide useful references for drilling a stepped microhole of nitride ceramic plates.
- 6 October 2021
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1088-1112
Cutting force, Vibration, and Temperature in Drilling on a Thermoplastic Material of PEEK
Polyetheretherketone (PEEK) is one of the semi-crystalline thermoplastic polymers with excellent machinability and chemical stability applied to precise structural plates and electronic components. This study installed multiple sensors to analyze the machining characteristics in the PEEK drilling. According to the time domain signals, the effects of spindle speed and feed rate on the machining characteristics of cutting force and vibration were investigated. In addition, an infrared thermography was installed to record the temperature variation within the drilling area. The experimental hole was 2-mm diameter with a 4.5-mm depth. Experimental results showed that the effect of the feed rate on thrust force is greater than the spindle speed; drilling by a low-level spindle speed with a low-level feed rate can obtain the smallest cutting force and acceleration amplitude in the spindle axis; the temperature within the drilling area is inverse to the feed rate and a high-level feed rate is helpful for forming regular curl chips. When adequate airflow was applied during the drilling operation, the hole’s shrinkage ratio and roundness can be decreased. The data presented in this paper provide valuable references for realizing the drilling of the thermoplastic—PEEK.
- 6 October 2021
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1088-1112
Cutting force, Vibration, and Temperature in Drilling on a Thermoplastic Material of PEEK
Polyetheretherketone (PEEK) is one of the semi-crystalline thermoplastic polymers with excellent machinability and chemical stability applied to precise structural plates and electronic components. This study installed multiple sensors to analyze the machining characteristics in the PEEK drilling. According to the time domain signals, the effects of spindle speed and feed rate on the machining characteristics of cutting force and vibration were investigated. In addition, an infrared thermography was installed to record the temperature variation within the drilling area. The experimental hole was 2-mm diameter with a 4.5-mm depth. Experimental results showed that the effect of the feed rate on thrust force is greater than the spindle speed; drilling by a low-level spindle speed with a low-level feed rate can obtain the smallest cutting force and acceleration amplitude in the spindle axis; the temperature within the drilling area is inverse to the feed rate and a high-level feed rate is helpful for forming regular curl chips. When adequate airflow was applied during the drilling operation, the hole’s shrinkage ratio and roundness can be decreased. The data presented in this paper provide valuable references for realizing the drilling of the thermoplastic—PEEK.
- 9 July 2002
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 20 (1) , 9-19
A Freeform Surface Modelling System Based on Laser Scan Data for Reverse Engineering
- 9 July 2002
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 20 (1) , 9-19
A Freeform Surface Modelling System Based on Laser Scan Data for Reverse Engineering