Jehyung Ok
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jehyung Ok has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Tae-Il Kim
School of Chemical Engineering Sungkyunkwan University (SKKU) Suwon Republic of Korea
4 shared publications - Byeonghak Park
School of Chemical Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
2 shared publications Joo Hwan Shin
School of Chemical Engineering, Sungkyunkwan University (SKKU), Suwon, Republic of Korea
2 shared publicationsSubin Park
School of Chemical Engineering Sungkyunkwan University (SKKU) Suwon Republic of Korea
2 shared publicationsChanho Jeong
Department of Biomedical Engineering, SKKU, Suwon 16419, Republic of Korea
1 shared publication- Hyesu Jeon
School of Chemical Engineering Sungkyunkwan University (SKKU) Suwon Republic of Korea
1 shared publication
Latest Publications
- 16 January 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (12) , e17030
Viscoelastic Phase Transition of Polyborodimethylsiloxane (PBDMS) for Mechanical Pass Filters and Noise Fading Sensor
Continuous monitoring of physiological signals is inevitably disrupted by motion artifacts and ambient mechanical noise. Signal processing is typically required to extract genuine physiological signals from motion artifacts, yet the signals can be distorted and classified incompletely. Previously, we presented a noise‐selective damper based on gelatin hydrogel and chitosan, however, the hydrogel is unstable due to dehydration. In addition, various types of mechanical filters, such as high‐pass, low‐pass, and band‐pass filters, are needed as alternatives to signal processing. Here, we present viscoelastic polyborodimethylsiloxane (PBDMS) based mechanical pass filters, which maintain stable damping properties for over three months. Dynamic bonding from hydrogen bonds and B─O bonds enables energy dissipation through chain rearrangement and entanglement. The damping behaviors can be tuned by adjusting its molecular weight. As molecular weight increases, the reconfiguration and re‐bonding of these chains slow down, resulting in a longer relaxation time. This molecular‐weight‐dependent relaxation behavior allows precise control over the transition frequency. Furthermore, by parallelly assembling materials with distinct phase transition characteristics, not only high‐pass, but also low‐pass and band‐pass mechanical filtering is achieved. Using PBDMS‐based wearable bioelectronics, we successfully separate more than two concurrent mechanical signals without any additional signal processing.
- 16 January 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (12) , e17030
Viscoelastic Phase Transition of Polyborodimethylsiloxane (PBDMS) for Mechanical Pass Filters and Noise Fading Sensor
Continuous monitoring of physiological signals is inevitably disrupted by motion artifacts and ambient mechanical noise. Signal processing is typically required to extract genuine physiological signals from motion artifacts, yet the signals can be distorted and classified incompletely. Previously, we presented a noise‐selective damper based on gelatin hydrogel and chitosan, however, the hydrogel is unstable due to dehydration. In addition, various types of mechanical filters, such as high‐pass, low‐pass, and band‐pass filters, are needed as alternatives to signal processing. Here, we present viscoelastic polyborodimethylsiloxane (PBDMS) based mechanical pass filters, which maintain stable damping properties for over three months. Dynamic bonding from hydrogen bonds and B─O bonds enables energy dissipation through chain rearrangement and entanglement. The damping behaviors can be tuned by adjusting its molecular weight. As molecular weight increases, the reconfiguration and re‐bonding of these chains slow down, resulting in a longer relaxation time. This molecular‐weight‐dependent relaxation behavior allows precise control over the transition frequency. Furthermore, by parallelly assembling materials with distinct phase transition characteristics, not only high‐pass, but also low‐pass and band‐pass mechanical filtering is achieved. Using PBDMS‐based wearable bioelectronics, we successfully separate more than two concurrent mechanical signals without any additional signal processing.
- Top Cited Papers
- 20 November 2023
- Published by Wiley in Advanced Materials
- Vol. 36 (1) , e2211595
Wearable and Implantable Cortisol‐Sensing Electronics for Stress Monitoring
Cortisol is a steroid hormone that is released from the body in response to stress. Although a moderate level of cortisol secretion can help the body maintain homeostasis, excessive secretion can cause various diseases, such as depression and anxiety. Conventional methods for cortisol measurement undergo procedures that limit continuous monitoring, typically collecting samples of bodily fluids, followed by separate analysis in a laboratory setting that takes several hours. Thus, recent studies demonstrate wearable, miniaturized sensors integrated with electronic modules that enable wireless real‐time analysis. Here, the primary focus is on wearable and implantable electronic devices that continuously measure cortisol concentration. Diverse types of cortisol‐sensing techniques, such as antibody‐, DNA‐aptamer‐, and molecularly imprinted polymer‐based sensors, as well as wearable and implantable devices that aim to continuously monitor cortisol in a minimally invasive fashion are discussed. In addition to the cortisol monitors that directly measure stress levels, other schemes that indirectly measure stress, such as electrophysiological signals and sweat are also summarized. Finally, the challenges and future directions in stress monitoring and management electronics are reviewed.
- 20 November 2023
- Published by Wiley in Advanced Materials
- Vol. 36 (1) , e2211595
Top Cited PapersWearable and Implantable Cortisol‐Sensing Electronics for Stress Monitoring
Cortisol is a steroid hormone that is released from the body in response to stress. Although a moderate level of cortisol secretion can help the body maintain homeostasis, excessive secretion can cause various diseases, such as depression and anxiety. Conventional methods for cortisol measurement undergo procedures that limit continuous monitoring, typically collecting samples of bodily fluids, followed by separate analysis in a laboratory setting that takes several hours. Thus, recent studies demonstrate wearable, miniaturized sensors integrated with electronic modules that enable wireless real‐time analysis. Here, the primary focus is on wearable and implantable electronic devices that continuously measure cortisol concentration. Diverse types of cortisol‐sensing techniques, such as antibody‐, DNA‐aptamer‐, and molecularly imprinted polymer‐based sensors, as well as wearable and implantable devices that aim to continuously monitor cortisol in a minimally invasive fashion are discussed. In addition to the cortisol monitors that directly measure stress levels, other schemes that indirectly measure stress, such as electrophysiological signals and sweat are also summarized. Finally, the challenges and future directions in stress monitoring and management electronics are reviewed.
- Open Access
- 30 May 2022
- Published by Springer Nature in npj Flexible Electronics
- Vol. 6 (1) , 1-12
Wearable EEG electronics for a Brain–AI Closed-Loop System to enhance autonomous machine decision-making
Human nonverbal communication tools are very ambiguous and difficult to transfer to machines or artificial intelligence (AI). If the AI understands the mental state behind a user’s decision, it can learn more appropriate decisions even in unclear situations. We introduce the Brain–AI Closed-Loop System (BACLoS), a wireless interaction platform that enables human brain wave analysis and transfers results to AI to verify and enhance AI decision-making. We developed a wireless earbud-like electroencephalography (EEG) measurement device, combined with tattoo-like electrodes and connectors, which enables continuous recording of high-quality EEG signals, especially the error-related potential (ErrP). The sensor measures the ErrP signals, which reflects the human cognitive consequences of an unpredicted machine response. The AI corrects or reinforces decisions depending on the presence or absence of the ErrP signals, which is determined by deep learning classification of the received EEG data. We demonstrate the BACLoS for AI-based machines, including autonomous driving vehicles, maze solvers, and assistant interfaces.
- 30 May 2022
- Published by Springer Nature in npj Flexible Electronics
- Vol. 6 (1) , 1-12
Open AccessWearable EEG electronics for a Brain–AI Closed-Loop System to enhance autonomous machine decision-making
Human nonverbal communication tools are very ambiguous and difficult to transfer to machines or artificial intelligence (AI). If the AI understands the mental state behind a user’s decision, it can learn more appropriate decisions even in unclear situations. We introduce the Brain–AI Closed-Loop System (BACLoS), a wireless interaction platform that enables human brain wave analysis and transfers results to AI to verify and enhance AI decision-making. We developed a wireless earbud-like electroencephalography (EEG) measurement device, combined with tattoo-like electrodes and connectors, which enables continuous recording of high-quality EEG signals, especially the error-related potential (ErrP). The sensor measures the ErrP signals, which reflects the human cognitive consequences of an unpredicted machine response. The AI corrects or reinforces decisions depending on the presence or absence of the ErrP signals, which is determined by deep learning classification of the received EEG data. We demonstrate the BACLoS for AI-based machines, including autonomous driving vehicles, maze solvers, and assistant interfaces.
- Top Cited Papers
- 6 May 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 376 (6593) , 624-629
Cuticular pad–inspired selective frequency damper for nearly dynamic noise–free bioelectronics
Bioelectronics needs to continuously monitor mechanical and electrophysiological signals for patients. However, the signals always include artifacts by patients’ unexpected movement (such as walking and respiration under approximately 30 hertz). The current method to remove them is a signal process that uses a bandpass filter, which may cause signal loss. We present an unconventional bandpass filter material—viscoelastic gelatin-chitosan hydrogel damper, inspired by the viscoelastic cuticular pad in a spider—to remove dynamic mechanical noise artifacts selectively. The hydrogel exhibits frequency-dependent phase transition that results in a rubbery state that damps low-frequency noise and a glassy state that transmits the desired high-frequency signals. It serves as an adaptable passfilter that enables the acquisition of high-quality signals from patients while minimizing signal process for advanced bioelectronics.
- 6 May 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 376 (6593) , 624-629
Top Cited PapersCuticular pad–inspired selective frequency damper for nearly dynamic noise–free bioelectronics
Bioelectronics needs to continuously monitor mechanical and electrophysiological signals for patients. However, the signals always include artifacts by patients’ unexpected movement (such as walking and respiration under approximately 30 hertz). The current method to remove them is a signal process that uses a bandpass filter, which may cause signal loss. We present an unconventional bandpass filter material—viscoelastic gelatin-chitosan hydrogel damper, inspired by the viscoelastic cuticular pad in a spider—to remove dynamic mechanical noise artifacts selectively. The hydrogel exhibits frequency-dependent phase transition that results in a rubbery state that damps low-frequency noise and a glassy state that transmits the desired high-frequency signals. It serves as an adaptable passfilter that enables the acquisition of high-quality signals from patients while minimizing signal process for advanced bioelectronics.