Egas José Armando
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Egas José Armando has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Omar Gatera
African Center of Excellence in Internet of Things, University of Rwanda, Kigali, Rwanda
4 shared publications - Damien Hanyurwimfura
African Center of Excellence in Internet of Things, University of Rwanda, Kigali, Rwanda
3 shared publications Athanase Nduwumuremyi
Department of Agriculture, Forestry and Bioresources and Department of Smart Systems, Seoul National University, Seoul, Republic of Korea
2 shared publications- Athanase Nduwumuremyi
Rwanda Agriculture Board, Kigali, Rwanda
2 shared publications - Cristiano Márcio Alves de Souza
Universidade Federal da Grande Dourados
2 shared publications - Kwang Soo Kim
Seoul National University (Seoul, Korea, Republic of)
2 shared publications
Latest Publications
- Open Access
- 14 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
An edge AIoT framework for optimizing the placement of integrated soil sensors in agricultural wireless sensor networks
- 14 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessAn edge AIoT framework for optimizing the placement of integrated soil sensors in agricultural wireless sensor networks
- Open Access
- 1 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Evaluation of advanced Kalman filter on real-time agricultural soil parameters through an IoT resources-constrained device
Effective sensor denoising is crucial for accurate, real-time agricultural decision-support systems. This study explores the application of Unscented Kalman Filter (UKF) extensions on resource-constrained devices to improve sensor denoising and enhance the reliability of Internet of Things (IoT) based agricultural soil monitoring. The study was conducted in Ruhango district, Rwanda, utilizing a wireless sensor node equipped with a Raspberry Pi 5 (ARM v8) and an integrated seven-in-one soil sensor measuring temperature, humidity, electrical conductivity, pH, nitrogen, phosphorus, and potassium. The sensor was placed at a depth of 20 cm in ten cassava farms, collecting data every 30 min for eight months. Four real-time sensor denoising models were implemented: UKF, Cubature Kalman Filter (CKF), UKF with Artificial Neural Network (UKF_ANN), and UKF with Fuzzy Logic (UKF_FL). Models’ performance was evaluated using boxplot, square root(R2), mean absolute error (MAE), root mean square error (RMSE), computation memory (CM), and computation time (CT). Data analysis was performed using Python 3.12 on ARM v8. Results demonstrated that CKF outperformed the other models, reducing RMSE by up to 32% and lowering CM and CT by 75%. CKF and UKF_ANN maintained the integrity of the censored data while effectively removing Gaussian, uniform, and salt-and-pepper noise, making them suitable for IoT-based soil monitoring systems.
- 1 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Open AccessEvaluation of advanced Kalman filter on real-time agricultural soil parameters through an IoT resources-constrained device
Effective sensor denoising is crucial for accurate, real-time agricultural decision-support systems. This study explores the application of Unscented Kalman Filter (UKF) extensions on resource-constrained devices to improve sensor denoising and enhance the reliability of Internet of Things (IoT) based agricultural soil monitoring. The study was conducted in Ruhango district, Rwanda, utilizing a wireless sensor node equipped with a Raspberry Pi 5 (ARM v8) and an integrated seven-in-one soil sensor measuring temperature, humidity, electrical conductivity, pH, nitrogen, phosphorus, and potassium. The sensor was placed at a depth of 20 cm in ten cassava farms, collecting data every 30 min for eight months. Four real-time sensor denoising models were implemented: UKF, Cubature Kalman Filter (CKF), UKF with Artificial Neural Network (UKF_ANN), and UKF with Fuzzy Logic (UKF_FL). Models’ performance was evaluated using boxplot, square root(R2), mean absolute error (MAE), root mean square error (RMSE), computation memory (CM), and computation time (CT). Data analysis was performed using Python 3.12 on ARM v8. Results demonstrated that CKF outperformed the other models, reducing RMSE by up to 32% and lowering CM and CT by 75%. CKF and UKF_ANN maintained the integrity of the censored data while effectively removing Gaussian, uniform, and salt-and-pepper noise, making them suitable for IoT-based soil monitoring systems.
- 28 January 2025
- Published by Springer Nature in Journal of Biosystems Engineering
- Vol. 50 (1) , 47-58
Enhancing Agricultural Internet of Things Data Accuracy: Evaluating Kalman Filter-Based Sensor Denoising Techniques
- 28 January 2025
- Published by Springer Nature in Journal of Biosystems Engineering
- Vol. 50 (1) , 47-58
Enhancing Agricultural Internet of Things Data Accuracy: Evaluating Kalman Filter-Based Sensor Denoising Techniques
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Remote Monitoring System in Real Time for Cattle Production, Through Low-Cost Technologies
This study aimed to development a cost-effective remote monitoring system for cattle management, using both hardware (motion sensor, jumpers, ESP32 camera, and TTL programmer) and software (Arduino IDE and a dashboard) components. A noteworthy strength of this study is its cost-efficient approach, successfully implemented for real-time animal monitoring with internet-based communication. The programming code was developed using the Arduino IDE, and then the validation was conducted in a cattle production corral encompassing calves, heifers, cows, and oxen. To validate the model, we used the confusion matrix and the Kappa index, that showed a good agreement, and confirming that the system is ease of use, secure, scalability, and cost-effective, enabling animal monitoring and data storage via dashboard. An economic evaluation, comparing costs and key features with RFID, Zigbee, Lora WAN, and ESP32CAM technologies, supports the conclusion that implementing this TTL-based system for animal monitoring, featuring remote real-time data collection and internet communication integration, is both possible and viable.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Remote Monitoring System in Real Time for Cattle Production, Through Low-Cost Technologies
This study aimed to development a cost-effective remote monitoring system for cattle management, using both hardware (motion sensor, jumpers, ESP32 camera, and TTL programmer) and software (Arduino IDE and a dashboard) components. A noteworthy strength of this study is its cost-efficient approach, successfully implemented for real-time animal monitoring with internet-based communication. The programming code was developed using the Arduino IDE, and then the validation was conducted in a cattle production corral encompassing calves, heifers, cows, and oxen. To validate the model, we used the confusion matrix and the Kappa index, that showed a good agreement, and confirming that the system is ease of use, secure, scalability, and cost-effective, enabling animal monitoring and data storage via dashboard. An economic evaluation, comparing costs and key features with RFID, Zigbee, Lora WAN, and ESP32CAM technologies, supports the conclusion that implementing this TTL-based system for animal monitoring, featuring remote real-time data collection and internet communication integration, is both possible and viable.
- Open Access
- 29 September 2023
- Published by Universidade Federal de Grande Dourados in Agrarian
- Vol. 16 (56) , e17226
Soil microbial biomass carbon and Jatropha curcas yield intecropping with forages and crop species
The domestication of Jatropha curcas L. in the Brazilian territory has been boosted by its great potential in the production of grains, oil and, in particular, its adaptation in different soil and climatic conditions. The aim of this research was evaluate the soil biological quality through the soil microbial biomass carbon and its indices derivate (metabolic and microbial quotient) under J. curcas intercropping with many forages species, legumes and annual crop rotation systems, as well as the accumulated production of J. curcas grains and oil. The experiment was conducted in a commercial area in the randomized blocks experimental design with the treatments arranged in a 12 x 2 factorial design, with four repetitions, resulting in 12 treatments with cropping systems and 2 sampling times (February 2012 and May 2012). Soil sampling was performed in February and May 2012, at 0 at 10 cm layer and four composite samples were collected in each cropping system, from five subsamples in each plot. J. curcas intercropping with B. ruziziensis, favors the maintenance of the community of soil microorganisms compared to the treatment with the species P. maximum cv. Massai and Cajanus cajan, which promoted decreasing in soil organic matter dynamics, when compared to the other cropping systems. The monocropping systems of J. curcas and intercropping in rotation systems 2 and 3 achieved higher yields of J. curcas grains and oil over three seasons.
- 29 September 2023
- Published by Universidade Federal de Grande Dourados in Agrarian
- Vol. 16 (56) , e17226
Open AccessSoil microbial biomass carbon and Jatropha curcas yield intecropping with forages and crop species
The domestication of Jatropha curcas L. in the Brazilian territory has been boosted by its great potential in the production of grains, oil and, in particular, its adaptation in different soil and climatic conditions. The aim of this research was evaluate the soil biological quality through the soil microbial biomass carbon and its indices derivate (metabolic and microbial quotient) under J. curcas intercropping with many forages species, legumes and annual crop rotation systems, as well as the accumulated production of J. curcas grains and oil. The experiment was conducted in a commercial area in the randomized blocks experimental design with the treatments arranged in a 12 x 2 factorial design, with four repetitions, resulting in 12 treatments with cropping systems and 2 sampling times (February 2012 and May 2012). Soil sampling was performed in February and May 2012, at 0 at 10 cm layer and four composite samples were collected in each cropping system, from five subsamples in each plot. J. curcas intercropping with B. ruziziensis, favors the maintenance of the community of soil microorganisms compared to the treatment with the species P. maximum cv. Massai and Cajanus cajan, which promoted decreasing in soil organic matter dynamics, when compared to the other cropping systems. The monocropping systems of J. curcas and intercropping in rotation systems 2 and 3 achieved higher yields of J. curcas grains and oil over three seasons.
- Open Access
- 1 December 2022
- Published by International Journal for Innovation Education and Research in International Journal for Innovation Education and Research
- Vol. 10 (12) , 1-22
Construction of low-cost benches to assist in teaching machine elements and small engine testing
The teaching practice in technical, technological, and engineering education requires well-structured laboratories with didactic resources that provide the actors in the teaching and learning process with better interaction between the topics covered and the search for a practice. Thus, it is fundamental that lecturing institutions have teaching resources in their laboratories that the lecturers would use to improve their teaching-learning process. A teaching bench is a good option among the previous didactic models. The machine elements didactic benches allow a better explanation and application of the relationships between the various mechanical elements and related several subjects. For this reason, this work aims to build two didactic benches to assist the teaching-learning process under technical and didactic standards for teaching courses and/or related subjects of machine elements and later performance of engine bench tests to ensure its operation. The first didactic bench aims to assist in classes in relevant subjects involving machine elements. It has several components in it, and its characteristics and functionalities can be visualized. It has an electric engine for activation and a Prony brake type that measures the motor's torque and power demands. Additionally, it allows the student to visualize the correlations of the various calculations with practice, such as transmission ratio, torque, and power. The second didactic bench concerns the analysis of internal combustion or electric engines' functionalities, in which several parameters are analyzed, such as speed motor, torque, power, and fuel consumption. The engine bench has a load cell, rotation sensor, and Prony brake type initially adapted to test two engine models (electric and internal combustion). This work was developed using machine design methodology, highlighting the informational, conceptual, preliminary, and detailed design. The didactic bench tests ensured that they could be used in the teaching-learning process for engineering students. Moreover, with the construction of the small engine test bench, it is possible to evaluate internal combustion engine operating parameters, such as power, strength, rotation, and fuel consumption.
- 1 December 2022
- Published by International Journal for Innovation Education and Research in International Journal for Innovation Education and Research
- Vol. 10 (12) , 1-22
Open AccessConstruction of low-cost benches to assist in teaching machine elements and small engine testing
The teaching practice in technical, technological, and engineering education requires well-structured laboratories with didactic resources that provide the actors in the teaching and learning process with better interaction between the topics covered and the search for a practice. Thus, it is fundamental that lecturing institutions have teaching resources in their laboratories that the lecturers would use to improve their teaching-learning process. A teaching bench is a good option among the previous didactic models. The machine elements didactic benches allow a better explanation and application of the relationships between the various mechanical elements and related several subjects. For this reason, this work aims to build two didactic benches to assist the teaching-learning process under technical and didactic standards for teaching courses and/or related subjects of machine elements and later performance of engine bench tests to ensure its operation. The first didactic bench aims to assist in classes in relevant subjects involving machine elements. It has several components in it, and its characteristics and functionalities can be visualized. It has an electric engine for activation and a Prony brake type that measures the motor's torque and power demands. Additionally, it allows the student to visualize the correlations of the various calculations with practice, such as transmission ratio, torque, and power. The second didactic bench concerns the analysis of internal combustion or electric engines' functionalities, in which several parameters are analyzed, such as speed motor, torque, power, and fuel consumption. The engine bench has a load cell, rotation sensor, and Prony brake type initially adapted to test two engine models (electric and internal combustion). This work was developed using machine design methodology, highlighting the informational, conceptual, preliminary, and detailed design. The didactic bench tests ensured that they could be used in the teaching-learning process for engineering students. Moreover, with the construction of the small engine test bench, it is possible to evaluate internal combustion engine operating parameters, such as power, strength, rotation, and fuel consumption.
- Open Access
- 12 May 2022
- Published by Revista Engenharia na Agricultura in REVISTA ENGENHARIA NA AGRICULTURA - REVENG
- Vol. 30, 97-110
Soil physical attributes and agronomic characteristics relationships of soybean in no-tillage
The objective of this work was to evaluate the soil physical attributes and their relationship to soybean productivity under no-tillage system. The study was conducted in a Oxisol, based on randomized blocks design, with the treatments: no-tillage for 10 years (0 tractor traffic) and five tractor-traffic intensities (2, 4, 6, 8, and 12 passes), with five repetitions. An increase of macroporosity up to 10% under soil bulk density ranging from 1.51 to 1.56 mg.m-3 and soil penetration resistance between 1.5 to 2.0 MPa, on the 0.00-0.10 m layer benefited the soybean productivity. The number of pods per plant, grain number per plant, stem diameter, and soybean productivity is higher in Oxisol, under intermediate compression. Soil bulk density and soil penetration resistance showed to be sensitive an indicators of soil physical quality, with more relation to soybean grain productivity.
- 12 May 2022
- Published by Revista Engenharia na Agricultura in REVISTA ENGENHARIA NA AGRICULTURA - REVENG
- Vol. 30, 97-110
Open AccessSoil physical attributes and agronomic characteristics relationships of soybean in no-tillage
The objective of this work was to evaluate the soil physical attributes and their relationship to soybean productivity under no-tillage system. The study was conducted in a Oxisol, based on randomized blocks design, with the treatments: no-tillage for 10 years (0 tractor traffic) and five tractor-traffic intensities (2, 4, 6, 8, and 12 passes), with five repetitions. An increase of macroporosity up to 10% under soil bulk density ranging from 1.51 to 1.56 mg.m-3 and soil penetration resistance between 1.5 to 2.0 MPa, on the 0.00-0.10 m layer benefited the soybean productivity. The number of pods per plant, grain number per plant, stem diameter, and soybean productivity is higher in Oxisol, under intermediate compression. Soil bulk density and soil penetration resistance showed to be sensitive an indicators of soil physical quality, with more relation to soybean grain productivity.
- Open Access
- 5 September 2021
- Published by Universidade Federal de Grande Dourados in Agrarian
- Vol. 14 (53) , 333-343
Depth, coverage and spacing of the furrows in mechanized sugarcane plantation with planter and distributor in the day and night shifts
Mechanized planting, is one of the main operations in the sugarcane production cycle that directly affects the longevity of the shoots, the crop yield and the profitability of the crop. Thus, this study aims to evaluate the furrow depth, furrow coverage and furrows spacing in a mechanized sugarcane plantation with a planter and a distributor in the day and night shifts of operation, using as statistical analysis quality control tool. In both shifts were sampled 30 points, where was collect data of furrow depth, furrow coverage and furrows spacing. The quality indicators of mechanized sugarcane planting are not influenced by the day and night shifts, and present values considered satisfactory when carrying out mechanized planting with a planter or distributor.
- 5 September 2021
- Published by Universidade Federal de Grande Dourados in Agrarian
- Vol. 14 (53) , 333-343
Open AccessDepth, coverage and spacing of the furrows in mechanized sugarcane plantation with planter and distributor in the day and night shifts
Mechanized planting, is one of the main operations in the sugarcane production cycle that directly affects the longevity of the shoots, the crop yield and the profitability of the crop. Thus, this study aims to evaluate the furrow depth, furrow coverage and furrows spacing in a mechanized sugarcane plantation with a planter and a distributor in the day and night shifts of operation, using as statistical analysis quality control tool. In both shifts were sampled 30 points, where was collect data of furrow depth, furrow coverage and furrows spacing. The quality indicators of mechanized sugarcane planting are not influenced by the day and night shifts, and present values considered satisfactory when carrying out mechanized planting with a planter or distributor.