JFJörg Fricke

Jörg Fricke

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jörg Fricke has a total of 82 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Heterogeneously integrated evanescently coupled lasers emitting in the submicrometre wavelength range

    by K. Akritidis, M. Billet, M. Kiewiet, J.-P. Koester, J. Fricke, P. Della Casa, H. Wenzel, J. Brouckaert, R. Jansen, G. Roelkens, et al.

    Owing to its broad transparency window, ultra-low propagation losses, and compatibility with complementary metal–oxide–semiconductor (CMOS) fabrication processes, silicon nitride (SiN) has emerged as a highly attractive platform for extending integrated photonics into the visible and near-infrared spectrum. By incorporating active components such as modulators, light sources, and detectors, complex photonic systems with unprecedented functionality and performance become possible. These systems enable a wide range of applications, including biosensing, on-chip spectroscopy, imaging, and quantum computing. However, the low refractive index of SiN relative to III–V gain materials poses a major challenge for implementing evanescently coupled lasers, the dominant coupling scheme in silicon photonics at the telecommunication wavelengths. Although a silicon intermediate layer is often used to alleviate this mismatch, its strong absorption at shorter wavelengths precludes its use. Here, we present an integration strategy that overcomes this limitation by employing a CMOS-compatible a-Si:H layer with two etch depths, which was engineered to achieve the required optical properties at shorter wavelengths. This intermediate structure enables efficient vertical coupling between the SiN photonic circuit and a micro-transfer-printed GaAs-based semiconductor optical amplifier. Using this scheme, we demonstrate on-chip amplification with a gain of more than 13 dB as well as lasing in the submicrometre wavelength range. Finally, we showcase the versatility of this process by integrating a second amplifier stage following the laser, achieving on-chip output powers exceeding 4 mW. These results highlight the potential of this method for developing fully integrated evanescently coupled laser systems operating in the near-infrared band.

  • Modeling and Characterization by Experiment of Higher Order Surface Bragg Gratings for Ultra-Narrow Linewidth Diode Lasers

    by S. Wenzel, O. Brox, J. Fricke, I. Nechepurenko, A. Tsarapkin, A. Wicht

    Bragg gratings for monolithic extended cavity diode lasers with ultra-narrow linewidth must exhibit a spectrally narrow resonance of the order of a few tens of gigahertz to enable longitudinal single mode operation. This requirement is met by higher order surface gratings in ridge-waveguides, combining a length of at least 2 mm with a small coupling coefficient. The modeling of such structures relies on major simplifications. In addition, the impact of uncertainties in the design and implementation is aggravated by the size of the grating. To optimize the design and evaluate the quality of the modeling and implementation, we developed and applied a procedure for the precise measurement of the grating reflectance and loss. In this work, we present our hybrid modeling approach based on eigenmode expansion complemented by coupled mode theory as well as our characterization procedure. We combine this with the analysis by scanning electron microscopy of our test structures. We find that measured spectra of gratings of up to 2 mm length agree well with the models, including the asymmetry of the loss vs. frequency caused by radiation effects. We also report a spectral filamentation of the reflectance spectrum of 4 mm long gratings with side features on the long wavelength side.


  • Open Access

    DBR Lasers at 679.29 and 707.20 nm for Efficient Repumping in Sr Optical Lattice Clocks

    by Nora Goossen-Schmidt, Bassem Arar, Jörg Fricke, Karl Häusler, Andre Maaßdorf, Max Schiemangk, Sandy Szermer, Hans Wenzel, Andreas Wicht

    We have developed and characterized DBR lasers emitting at 679 nm and 707 nm, specifically tailored to excite the repumping wavelengths in Sr optical lattice clocks. They achieve a FWHM linewidth of about 1MHz at optical output powers of more than 65 mW.


  • Open Access

    420 W pulse power from a 905 nm distributed bragg reflector laser with multiple active regions and tunnel junctions

    by Nor Ammouri, Heike Christopher, Andre Maaßdorf, Jörg Fricke, Arnim Ginolas, Armin Liero, Hans Wenzel, Andrea Knigge, Günther Tränkle

    We report a record-high pulse power of 420 W or a pulse energy of 4.2 μJ at a pulse current of 210 A, emitted by a single distributed Bragg reflector broad-area laser with 5 active regions separated by 4 tunnel junctions. The laser is operated with nanosecond current pulses at a repetition frequency of 10 kHz so that optical pulses with a width of 10 ns are emitted. The emission spectrum exhibits a spectral peak at approximately 905 nm at 25 °C with a spectral width of less than 0.2 nm and a temperature-related shift of 63 pm K−1. We also investigate the dependence of the output power on cavity length and number of active regions. A 4 mm long laser with 3 active regions achieves a pulse power of 272 W at 150 A. At the same current, 2 mm long lasers with 3 and 5 active regions achieve output powers of 167 W and 283 W, respectively. Despite its shorter cavity, the 2 mm long 5 active region laser delivers 10 W more output power at 150 A than the 4 mm long laser with 3 active regions. All lasers under study have a p-contact stripe width of 200 μm.


  • Open Access

    Tunable and Wavelength‐Stabilised Laser Based on a Bragg Reflection Waveguide for Spontaneous Parametric Down Conversion

    by Thomas Tenzler, Christof Zink, Jörg Fricke, Pietro Della Casa, Jos Boschker, Maximilian Schäfer, Hans Wenzel, Andrea Knigge

    Bragg reflection waveguide lasers offer compact solutions for the generation of photon pairs through spontaneous parametric down conversion, by simultaneously generating the lasing pump light and converting it into photon pairs within the same device. However, the acceptance bandwidth of the lasing light for this conversion process is small, which makes free‐runnning Fabry–Pérot lasers with no wavelength stabilisation less suitable for nonlinear processes. We present the emission characteristics of a Bragg reflection ridge waveguide laser where a surface Bragg grating is implemented in one segment of the device. The lasing wavelength, determined by the Bragg condition, can be adjusted by the period of the grating between 775 and 785 nm. Furthermore, a micro heater in the grating section enables additional tuning of the lasing wavelength by 2 nm.


  • Open Access

    Repetition Frequency Detuning in Mode‐Locked Lasers with Integrated S‐Bend Waveguide

    by Shulin Wohlfeil, Jan‐Philipp Koester, Heike Christopher, Jörg Fricke, Pietro Della Casa, Hans Wenzel, Andrea Knigge, Günther Tränkle

    We present the integration of an S‐bend waveguide into the cavity of a mode‐locked diode laser to tune its repetition frequency for use in terahertz time‐domain spectroscopy applications. The mode‐locked diode laser, featuring a facet‐to‐facet 6‐mm‐long straight ridge waveguide, emits light at a wavelength of around 830 nm and operates at a repetition frequency of 6.3 GHz. By incorporating an S‐bend into the cavity, the optical path length can be modified, enabling a variation of up to 12 MHz in the repetition frequency. Furthermore, this approach supports the co‐integration of two lasers on a single chip, each with a distinct repetition rate but operating under identical environmental and driving conditions, offering a robust and compact two‐laser solution for asynchronous optical sampling.


  • Open Access

    GaAs-based photonic integrated circuit platform enabling monolithic ring-resonator-coupled lasers

    by Jan-Philipp Koester, Hans Wenzel, Jörg Fricke, Matthias Reggentin, Pietro Della Casa, Poojitha Sammeta, Olaf Brox, Michael Ekterai, Mario Kohlbrenner, Andreas Renkewitz, et al.

    This paper reports on a monolithically integrated gallium arsenide (GaAs)-based photonic integrated circuit platform for wavelengths around 1064 nm. Enabled by spatially selective quantum well removal and two-step epitaxial growth, it supports on-chip gain as well as passive waveguides. In addition, shallow- and deep-etched waveguides are realized. The former result in waveguide losses of less than 2 dB/cm, while the latter enable compact integrated waveguide components. To demonstrate the performance of the platform, racetrack ring resonators based on deep-etched Euler bends and shallow-etched directional couplers are realized, achieving high intrinsic quality factors of 2.6 × 105 and 3.2 × 105 for the fundamental TE and TM mode, respectively. To demonstrate the use of these resonators, ring-resonator-coupled lasers are fabricated, resulting in one-sided output powers of up to 14 mW and single-mode operation with 40 dB side-mode suppression. The successful integration of ring resonators on a GaAs-based active/passive photonic integrated circuit platform paves the way for the realization of fully monolithic, widely tunable, and narrow linewidth ring-resonator-coupled laser sources.


  • Wavelength-Stabilized Multi-Active Region DBR and DFB Broad-Area and Ridge-Waveguide Lasers for High Peak-Power Pulsed Operation

    by Heike Christopher, Nor Ammouri, Maximilian Beier, Jörg Fricke, Arnim Ginolas, Jan-Philipp Koester, Armin Liero, Andre Maaßdorf, Sonja Nozinic, Hans Wenzel, et al.

    For LiDAR applications, compact, robust, and mass-producible light sources generating high-peak power nanosecond-long pulses are essential. This paper presents an investigation of power scaling in semiconductor lasers via the number of epitaxially stacked active regions in a single vertical waveguide supporting a higher order mode, chip length, output aperture width, and lateral waveguide design. All devices are wavelength-stabilized using surface gratings integrated either as a passive section at the rear facet of the diode laser as a distributed-Bragg-reflector (DBR) or along the full length of the chip in a distributed feedback (DFB) design. A 4 mm long broad-area (BA) DBR laser with a stripe width of 200 $\mu$ m and five active regions delivered approximately 171 W at 80 A, a factor of 6.6 more peak pulse power than the standard 6 mm long single active region DBR laser with 50 $\mu$ m stripe width. A corresponding 3 mm long 3-active region DFB-BA laser achieved more than 125 W at 129 A. These BA lasers have a lateral beam propagation ratio M $^{2}\approx$ 30. In contrast, weakly tapered ridge waveguide (TRW) lasers were found to generate more than 20 W with an M $^{2}$ of about 3 and an excellent lateral brightness of 24 W $\cdot$ mm $^{-1}$ mrad $^{-1}$ .


  • Open Access

    Monolithically integrated multimode interference coupler-based master oscillator power amplifier with dual-wavelength emission around 830 nm

    by André Müller, Jan-Philipp Koester, Lara Sophie Theurer, Jörg Fricke, Hans Wenzel, Andrea Knigge, Bernd Sumpf

    A monolithically integrated dual-wavelength multimode interference coupler-based master oscillator power amplifier is presented. It consists of two shallowly etched, laterally separated ridge waveguide laser cavities as master oscillators with individual distributed Bragg reflector gratings as cavity mirrors. A deeply etched coupling section containing S-bend shaped waveguides and a multimode interference coupler is used to couple the laser emission of the master oscillators into a shallowly etched single waveguide serving as power amplifier. Changing the etch depth for the coupling section enables a compact device layout. In addition, increased radiation angles of modes not coupled into the power amplifier help to suppress beam steering, otherwise indicated by laterally separated far-field intensity distributions. The device provides 0.5 W of dual-wavelength emission around 830 nm in individual and common operation. As designed, both emission wavelengths are separated by 0.5 nm with spectral widths below 20 pm, limited by the spectral resolution of the spectrometer. Both peak wavelengths remain within spectral windows of 50 pm within the available power range. This enables full flexibility selecting operating points for applications such as shifted excitation Raman difference spectroscopy and the generation of THz emission by photomixing. The emission wavelengths can additionally be non-continuously tuned by applying a heater current to resistors implemented next to the distributed Bragg reflector gratings. As an example, selected spectral distances of 0.5 nm, 1.0 nm, 1.5 nm, and 2.0 nm are demonstrated. Near field widths of 5 μm and far field angles of 17° result in beam propagation ratios of 1.4 (1/e2) in all operation modes and enable easy beam shaping or optical single-mode fiber coupling.


  • Single mode 660 nm DBR tapered laser with 1 W optical output power

    by Gunnar Blume, Oliver Matalla, Hans Wenzel, Andre Maassdorf, David Feise, Jörg Fricke, Peter Ressel, Sabrina Kreutzmann, Arnim Ginolas, Alexander Sahm, et al.

    For several non-destructive spectroscopy methods based on quantum mechanical effects (e.g. MID-IR quantum-OCT) the size of currently used solid state lasers prevents effective miniaturization. Red-emitting diode lasers with single longitudinal and single lateral mode emission are therefore required for successful out-of-the lab usage. To address this challenge, the FBH developed specialized tapered lasers (TPL) emitting near 660 nm with an integrated tenth order distributed Bragg reflector (DBR) surface grating, requiring only a single epitaxy step. The facets were passivated and coated to obtain reflectivities of 5% for the front and 30% for the rear facet. The DBR-TPL chips were mounted p-side down on CVD-diamonds with structured contacts to allow separate contacting of the ridge waveguide (RW) and tapered (TP) sections. The DBR-TPLs feature a nearly diffraction limited output beam with a spectral width below 0.5 pm, corresponding to a coherence length of almost 1 m. An optical output power of more than 1 W could be demonstrated at currents of 50 mA and 2.5 A for the RW and TP sections, respectively. The beam quality at 1 W was M21/e2 = 1.1 (M24σ = 2.1). The DBR-TPLs are a first important component in the concept for a miniaturized portable quantum-OCT scanner. Here, the sample will be illuminated with MID-IR photons while the entangled NIR photons will be measured with a cost-effective, Si-based spectrometer.