Georg Brösigke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Georg Brösigke has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
Jens-Uwe Repke
10 shared publications- Jens-Uwe Repke
Process Dynamics and Operations Group, Technische Universität Berlin, Straße des 17. Juni 135, 10623 Berlin, Germany
7 shared publications - Mudassar Javed
Process Dynamics and Operations Group Technische Universität Berlin Straße des 17. Juni 135 10623 Berlin Germany
5 shared publications - Reinhard Schomäcker
Technische Universität Berlin, Department of Chemistry, Straße des 17. Juni 124, 10623, Berlin, Germany
4 shared publications - Aleksander Gurlo
Technische Universität Berlin, Chair of Advanced Ceramic Materials, Straße des 17. Juni 135, 10623 Berlin, Germany
3 shared publications - Maged F. Bekheet
Technische Universität Berlin, Faculty III Process Sciences, Institute of Materials Science and Technology, Chair of Advanced Ceramic Materials, Straße des 17. Juni 135, 10623 Berlin, Germany
3 shared publications
Latest Publications
- Open Access
- 4 October 2026
- Published by Elsevier in SSRN Electronic Journal
Characterizing the Fluid-Dynamic Operating Range of Rotating Zigzag Beds: Experimental Validation of a Wet Pressure Drop Model to Predict Flooding
In the strive towards process intensification, the substitution of gravitational acceleration with centrifugal force as the principle driving force has led to the development of High Gravity (HiGee) technology as a potential alternative to separation columns. While many HiGee designs have emerged, the rotating zigzag bed (RZB) has attracted increasing interest within the research field as it supplements its rotating internals with stationary elements. Despite the importance of quantifying the separation performance these zigzag internals offer, it is the fluid dynamics setting the boundaries for operation. Reliable information on conditions under which flooding occurs and the wet pressure drop across the entire operation range is scarcely available. Thus, the underlying mechanisms of delimiting operation states lacks substantial understanding. This study provides a fluid-dynamic investigation of the operation window of various zigzag geometries under a wide range of liquid and gas loads at varying rotational speeds down to the flooding regime. Physical terms for gas-liquid interaction are developed and incorporated into an experimentally validated wet pressure drop model. The model is able to accurately predict experimental wet pressure drop data and delimit states including loading points of varying zigzag geometries and load capacities. Furthermore, a new Sherwood-Shipley-Holloway correlation is proposed for flooding in RZBs to enable an equitable comparison between varying internal geometries omitting the necessity to conduct experiments.
- 4 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterizing the Fluid-Dynamic Operating Range of Rotating Zigzag Beds: Experimental Validation of a Wet Pressure Drop Model to Predict Flooding
In the strive towards process intensification, the substitution of gravitational acceleration with centrifugal force as the principle driving force has led to the development of High Gravity (HiGee) technology as a potential alternative to separation columns. While many HiGee designs have emerged, the rotating zigzag bed (RZB) has attracted increasing interest within the research field as it supplements its rotating internals with stationary elements. Despite the importance of quantifying the separation performance these zigzag internals offer, it is the fluid dynamics setting the boundaries for operation. Reliable information on conditions under which flooding occurs and the wet pressure drop across the entire operation range is scarcely available. Thus, the underlying mechanisms of delimiting operation states lacks substantial understanding. This study provides a fluid-dynamic investigation of the operation window of various zigzag geometries under a wide range of liquid and gas loads at varying rotational speeds down to the flooding regime. Physical terms for gas-liquid interaction are developed and incorporated into an experimentally validated wet pressure drop model. The model is able to accurately predict experimental wet pressure drop data and delimit states including loading points of varying zigzag geometries and load capacities. Furthermore, a new Sherwood-Shipley-Holloway correlation is proposed for flooding in RZBs to enable an equitable comparison between varying internal geometries omitting the necessity to conduct experiments.
- Open Access
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Triply periodic minimal surface packings for rotating packed beds: pressure drop, flooding and liquid distribution
Rotating packed beds (RPBs) intensify gas–liquid contact, but their compact design requires uniformly distributed liquid through the packing. Additive manufacturing allows packings based on triply periodic minimal surfaces (TPMS), whose porosity and specific surface area (SSA) can be set independently. Sixteen 3D-printed gyroid, diamond and split-P TPMS packings, covering 64–83% overall porosity and 719–1399 m²/m³ SSA and including two radial gradient designs, were tested in a transparent RPB against a commercial metal foam. Wet pressure drop and flooding were measured at 63 operating points per packing (200–1800 rpm, 60–150 kg/h liquid, 20–80 m³/h gas) and the axial droplet distribution was measured by phase Doppler anemometry. Pressure drop follows the free cross-section and rises by up to 19% from 83% to 64% porosity and by 16% over the SSA range. Both radial gradient designs, reported to favour mass transfer, add no high-speed pressure-drop penalty. Above the flooding region the three topologies agree to within about 10%, while in the flooding region the split-P floods first. An empirical model in rotational speed, gas flow rate, SSA and porosity describes all sixteen packings to a pooled mean absolute deviation of 3.5%. Most gyroids centre the liquid within 3.5 mm of the symmetry plane, the diamond displaces it by more than 7.5 mm, and the split-P and the metal foam stay centred. The structure sets the sign of the displacement, while the operating point adds a common shift caused by the gas flow in the cavity.
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTriply periodic minimal surface packings for rotating packed beds: pressure drop, flooding and liquid distribution
Rotating packed beds (RPBs) intensify gas–liquid contact, but their compact design requires uniformly distributed liquid through the packing. Additive manufacturing allows packings based on triply periodic minimal surfaces (TPMS), whose porosity and specific surface area (SSA) can be set independently. Sixteen 3D-printed gyroid, diamond and split-P TPMS packings, covering 64–83% overall porosity and 719–1399 m²/m³ SSA and including two radial gradient designs, were tested in a transparent RPB against a commercial metal foam. Wet pressure drop and flooding were measured at 63 operating points per packing (200–1800 rpm, 60–150 kg/h liquid, 20–80 m³/h gas) and the axial droplet distribution was measured by phase Doppler anemometry. Pressure drop follows the free cross-section and rises by up to 19% from 83% to 64% porosity and by 16% over the SSA range. Both radial gradient designs, reported to favour mass transfer, add no high-speed pressure-drop penalty. Above the flooding region the three topologies agree to within about 10%, while in the flooding region the split-P floods first. An empirical model in rotational speed, gas flow rate, SSA and porosity describes all sixteen packings to a pooled mean absolute deviation of 3.5%. Most gyroids centre the liquid within 3.5 mm of the symmetry plane, the diamond displaces it by more than 7.5 mm, and the split-P and the metal foam stay centred. The structure sets the sign of the displacement, while the operating point adds a common shift caused by the gas flow in the cavity.
- Open Access
- 14 August 2026
- Published by Elsevier in Chemical Engineering Journal
- Vol. 547
Reduced order CFD framework for kinetic parameter estimation in reactive flow applications
- 14 August 2026
- Published by Elsevier in Chemical Engineering Journal
- Vol. 547
Open AccessReduced order CFD framework for kinetic parameter estimation in reactive flow applications
- Open Access
- 26 March 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 330
Developing CO2-to-DME tandem kinetic model: Integrating methanol and DME synthesis under a unified framework
- 26 March 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 330
Open AccessDeveloping CO2-to-DME tandem kinetic model: Integrating methanol and DME synthesis under a unified framework
- Open Access
- 15 October 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 524
Comprehensive structural performance study of multi-core–shell catalysts through an experimental/numerical approach: Cyclohexane dehydrogenation case study
- 15 October 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 524
Open AccessComprehensive structural performance study of multi-core–shell catalysts through an experimental/numerical approach: Cyclohexane dehydrogenation case study
- Open Access
- 14 July 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (37)
Structured Multilayer Thin Films for Catalytic Applications: A Novel Approach on Catalyst Design Utilizing Microfabrication Techniques
The metal/metal oxide interface is key to establishing catalytic performance, selectivity, and stability in heterogeneous systems. In this proof‐of‐concept study, a systematic methodology is introduced for the preparation of multilayer catalysts that combines Radio Frequency (RF) magnetron sputtering with laser microstructuring for the synthesis of high‐density Cu/ZnO interfaces. By means of a specifically designed split target, alternating few‐nanometer‐thick layers of Cu and ZnO are deposited under precise control and with high reproducibility. Laser scribing is then employed to create defined microstructures that reveal buried interfaces, improving access to catalytically active interfaces. As‐deposited and laser‐scribed multilayer's structural and chemical stability is confirmed through Atomic Force Microscopy (AFM), X‐Ray Fluorescence (XRF), X‐Ray Diffraction (XRD), X‐Ray Photoelectron Spectroscopy (XPS), and Scanning Electron Microscope (SEM) characterizations. Catalytic activity is evaluated under gradient‐free, continuous‐stirring conditions for CO 2 hydrogenation to methanol where the catalyst produces methanol and CO under laboratory‐scale conditions. The strategy addresses specific design bottlenecks such as limited control over interfacial geometry and exposure while acknowledging the inherent limitations of thin‐film systems in terms of surface area and scalability. While demonstrated for CO 2 ‐to‐methanol conversion, the method is generally applicable to other interface‐dependent reactions. Building on this initial demonstration, forthcoming efforts will focus on detailed mechanistic analysis, long‐duration testing, and performance benchmarking against conventional powder‐based catalysts.
- 14 July 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (37)
Open AccessStructured Multilayer Thin Films for Catalytic Applications: A Novel Approach on Catalyst Design Utilizing Microfabrication Techniques
The metal/metal oxide interface is key to establishing catalytic performance, selectivity, and stability in heterogeneous systems. In this proof‐of‐concept study, a systematic methodology is introduced for the preparation of multilayer catalysts that combines Radio Frequency (RF) magnetron sputtering with laser microstructuring for the synthesis of high‐density Cu/ZnO interfaces. By means of a specifically designed split target, alternating few‐nanometer‐thick layers of Cu and ZnO are deposited under precise control and with high reproducibility. Laser scribing is then employed to create defined microstructures that reveal buried interfaces, improving access to catalytically active interfaces. As‐deposited and laser‐scribed multilayer's structural and chemical stability is confirmed through Atomic Force Microscopy (AFM), X‐Ray Fluorescence (XRF), X‐Ray Diffraction (XRD), X‐Ray Photoelectron Spectroscopy (XPS), and Scanning Electron Microscope (SEM) characterizations. Catalytic activity is evaluated under gradient‐free, continuous‐stirring conditions for CO 2 hydrogenation to methanol where the catalyst produces methanol and CO under laboratory‐scale conditions. The strategy addresses specific design bottlenecks such as limited control over interfacial geometry and exposure while acknowledging the inherent limitations of thin‐film systems in terms of surface area and scalability. While demonstrated for CO 2 ‐to‐methanol conversion, the method is generally applicable to other interface‐dependent reactions. Building on this initial demonstration, forthcoming efforts will focus on detailed mechanistic analysis, long‐duration testing, and performance benchmarking against conventional powder‐based catalysts.
- Open Access
- 3 June 2025
- Published by Elsevier in Chemical Engineering and Processing - Process Intensification
- Vol. 216
Less pressure loss with extra packing — The counterintuitive behavior of rotating packed beds
- 3 June 2025
- Published by Elsevier in Chemical Engineering and Processing - Process Intensification
- Vol. 216
Open AccessLess pressure loss with extra packing — The counterintuitive behavior of rotating packed beds
- Open Access
- 24 April 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 247
Enhancing mass transfer in falling liquid films: The impact of sharp-edged microstructures
- 24 April 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 247
Open AccessEnhancing mass transfer in falling liquid films: The impact of sharp-edged microstructures
- Open Access
- 18 January 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 241
Experimental diffusivity measurements using non-invasive laser-induced luminescence (PLIF & PLIF-I) in non-binary fluid multiphase domains
- 18 January 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 241
Open AccessExperimental diffusivity measurements using non-invasive laser-induced luminescence (PLIF & PLIF-I) in non-binary fluid multiphase domains