Sohail Shah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sohail Shah has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Mukesh Bachhav
Idaho National Laboratory
5 shared publications Mukesh Bachhav
4 shared publicationsTiankai Yao
4 shared publications- Yachun Wang
Idaho National Laboratory (INL), Idaho Falls, ID (United States)
3 shared publications - Arnold Pradhan2 shared publications
Assel Aitkaliyeva
2 shared publications
Latest Publications
- Open Access
- 9 October 2026
- Published by Elsevier in SSRN Electronic Journal
Segregation Behavior in Thermally Aged vs Neutron-Irradiated Commercial Pressure Vessel Steel Heat Affected Zone Using Atom Probe Tomograph
This study considers the effect of thermal aging and irradiation on solute segregation behavior in commercial pressurized water reactor pressure vessel steel taken from a commercial pressurizer and commercial surveillance capsule. The thermally aged and irradiated materials were in-service for 300,000 hours at 345°C and irradiated at 288°C to a fluence of 5.14x1019 n/cm2 (E> 1 MeV), respectively. Atom probe tomography was used to examine solute clustering and grain boundary segregation behavior in both sample sets. The thermally aged sample exhibits solute segregation to the grain boundary without characteristic solute clustering, while the irradiated sample exhibits both clustering and grain boundary segregation. Additionally, the clusters observed in the irradiated material exhibit differences in chemical composition based on nucleation at the grain boundary versus the matrix. The solute behavior is explained in the context of compositional and sink driving factors. These findings help further understand the behavior of pressure boundary materials critical for long-term operation of light water reactors.
- 9 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSegregation Behavior in Thermally Aged vs Neutron-Irradiated Commercial Pressure Vessel Steel Heat Affected Zone Using Atom Probe Tomograph
This study considers the effect of thermal aging and irradiation on solute segregation behavior in commercial pressurized water reactor pressure vessel steel taken from a commercial pressurizer and commercial surveillance capsule. The thermally aged and irradiated materials were in-service for 300,000 hours at 345°C and irradiated at 288°C to a fluence of 5.14x1019 n/cm2 (E> 1 MeV), respectively. Atom probe tomography was used to examine solute clustering and grain boundary segregation behavior in both sample sets. The thermally aged sample exhibits solute segregation to the grain boundary without characteristic solute clustering, while the irradiated sample exhibits both clustering and grain boundary segregation. Additionally, the clusters observed in the irradiated material exhibit differences in chemical composition based on nucleation at the grain boundary versus the matrix. The solute behavior is explained in the context of compositional and sink driving factors. These findings help further understand the behavior of pressure boundary materials critical for long-term operation of light water reactors.
- Open Access
- 12 August 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 633
TEM characterization of two variants of fuel-cladding chemical interaction in a HT-9 Clad U-10Zr fuel. Variant 2: FCCI without a Zr rind
- 12 August 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 633
Open AccessTEM characterization of two variants of fuel-cladding chemical interaction in a HT-9 Clad U-10Zr fuel. Variant 2: FCCI without a Zr rind
- Open Access
- 30 May 2026
- Published by Elsevier in SSRN Electronic Journal
TEM characterization of two variants of fuel-cladding chemical interaction in a HT-9 Clad U-10Zr Fuel. Variant 2: FCCI without a Zr Rind
This study uses transmission electron microscopy (TEM) and atom probe tomography (APT) to characterize a region of intense fuel-cladding chemical interaction (FCCI) in an HT9-clad U-10Zr fuel irradiated in FFTF to 12.6 at.% burnup at a time-averaged inner cladding temperature of 501 °C. In the absence of a protective Zr-rind, Fe and Cr infiltrated the fuel to a depth of ~130 µm and produced five distinct reaction layers of U-Fe binaries and ternary U-Zr-Fe phases. The analysis revealed three findings that refine the current understanding of FCCI: ternary U-Zr-Fe phases formed as multiple allotropes not predicted by equilibrium phase diagrams, Cr infiltration into the fuel was gated by prior Fe-driven phase formation and cladding decarburization rather than occurring as an independent diffusion process, and the complex lanthanide-attacked cladding wastage layer was identified as Ln3(Fe,Cr)29 rather than the Ln2Fe17 commonly assigned in the literature. Transmutation-generated Pu was also detected at the interface within a Ce-rich Fe-based intermetallic. These results show that FCCI severity is governed by local interfacial chemistry and indicate that predictive mechanistic models will require further experimental assessments of the U-Zr-Fe-Cr and (Fe,Cr)-Ln systems.
- 30 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTEM characterization of two variants of fuel-cladding chemical interaction in a HT-9 Clad U-10Zr Fuel. Variant 2: FCCI without a Zr Rind
This study uses transmission electron microscopy (TEM) and atom probe tomography (APT) to characterize a region of intense fuel-cladding chemical interaction (FCCI) in an HT9-clad U-10Zr fuel irradiated in FFTF to 12.6 at.% burnup at a time-averaged inner cladding temperature of 501 °C. In the absence of a protective Zr-rind, Fe and Cr infiltrated the fuel to a depth of ~130 µm and produced five distinct reaction layers of U-Fe binaries and ternary U-Zr-Fe phases. The analysis revealed three findings that refine the current understanding of FCCI: ternary U-Zr-Fe phases formed as multiple allotropes not predicted by equilibrium phase diagrams, Cr infiltration into the fuel was gated by prior Fe-driven phase formation and cladding decarburization rather than occurring as an independent diffusion process, and the complex lanthanide-attacked cladding wastage layer was identified as Ln3(Fe,Cr)29 rather than the Ln2Fe17 commonly assigned in the literature. Transmutation-generated Pu was also detected at the interface within a Ce-rich Fe-based intermetallic. These results show that FCCI severity is governed by local interfacial chemistry and indicate that predictive mechanistic models will require further experimental assessments of the U-Zr-Fe-Cr and (Fe,Cr)-Ln systems.
- Open Access
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Fission Products in Fuel Cladding Chemical Interaction (FCCI) Region of ATR-Irradiated HT9-Clad U-10MTZ (10MTZ=5Mo-4.3Ti-0.7Zr, wt.%) Metallic Fuel
Fuel-cladding chemical interaction (FCCI) is an important phenomenon in metallic nuclear fuels, as it directly influences fuel performance, cladding integrity, and overall reactor safety. A detailed understanding of FCCI mechanisms and the role of fission products is essential for designing and developing advanced fuel systems with improved irradiation performance. In this study, we investigated the FCCI region on the cladding side of HT9 ferritic-martensitic steel in contact with U-10MTZ fuel (10MTZ = 5Mo-4.3Ti-0.7Zr, wt.%), irradiated in the Advanced Test Reactor to 2.2 at.% burnup. High-resolution characterization techniques, including transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), and atom probe tomography (APT), were employed to examine microstructural evolution and fission product distributions in the FCCI region. TEM revealed Ti-rich precipitates along grain boundaries of the cubic (U,Zr)(Fe,Cr)₂ phase. EELS detected Ba and lanthanide fission products (Ln-FPs) within isolated pores. APT identified a wide range of fission products, including Kr, Te, Gd, and Dy, as well as a distinct band of Zr, Ti, C, and Sn adjacent to a pore. APT tips from the HT9 cladding region exhibited carbon depletion without evidence of elemental clustering. These findings provide new insights into the spatial distribution and chemical behavior of fission products and their influence on microstructural evolution under irradiation, establishing a benchmark for future studies on FCCI mechanisms in irradiated U-10MTZ metallic fuels.
- 20 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFission Products in Fuel Cladding Chemical Interaction (FCCI) Region of ATR-Irradiated HT9-Clad U-10MTZ (10MTZ=5Mo-4.3Ti-0.7Zr, wt.%) Metallic Fuel
Fuel-cladding chemical interaction (FCCI) is an important phenomenon in metallic nuclear fuels, as it directly influences fuel performance, cladding integrity, and overall reactor safety. A detailed understanding of FCCI mechanisms and the role of fission products is essential for designing and developing advanced fuel systems with improved irradiation performance. In this study, we investigated the FCCI region on the cladding side of HT9 ferritic-martensitic steel in contact with U-10MTZ fuel (10MTZ = 5Mo-4.3Ti-0.7Zr, wt.%), irradiated in the Advanced Test Reactor to 2.2 at.% burnup. High-resolution characterization techniques, including transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), and atom probe tomography (APT), were employed to examine microstructural evolution and fission product distributions in the FCCI region. TEM revealed Ti-rich precipitates along grain boundaries of the cubic (U,Zr)(Fe,Cr)₂ phase. EELS detected Ba and lanthanide fission products (Ln-FPs) within isolated pores. APT identified a wide range of fission products, including Kr, Te, Gd, and Dy, as well as a distinct band of Zr, Ti, C, and Sn adjacent to a pore. APT tips from the HT9 cladding region exhibited carbon depletion without evidence of elemental clustering. These findings provide new insights into the spatial distribution and chemical behavior of fission products and their influence on microstructural evolution under irradiation, establishing a benchmark for future studies on FCCI mechanisms in irradiated U-10MTZ metallic fuels.
- Open Access
- 4 April 2026
- Published by Elsevier in SSRN Electronic Journal
Phase stability of a Zr-Ru BCC+B2 eutectic refractory alloy during annealing and proton irradiation
Alloying refractory metals with Ru is a promising approach to obtain BCC+B2 microstructures. The current paper investigates a simple Zr-Ru binary alloy to gain fundamental insights into the effect of Ru on the phase stability. The composition of interest, 80Zr-20Ru (at.%), is a near-eutectic composition that consists of lamellar BCC and B2 phases. High-temperature annealing of this as-cast microstructure at 1150 °C coarsened the lamellar B2 into a blocky morphology, with a corresponding reduction in B2 number density. Aging at 600 °C transformed the BCC matrix phase into HCP and B2 phases via a divorced eutectoid reaction. This result indicates that the current experimental and computed Zr-Ru phase diagram requires revision. While the untransformed BCC phase exhibited a clear ω formation tendency, the distortions in the diffraction patterns recorded near the BCC-HCP reaction front are inconsistent with the ω displacements and potentially indicate a different displacement wave before transforming to HCP. During proton irradiation at 600 °C, the BCC phase underwent phase transformations depending on the initial microstructure. When the as-cast sample was irradiated at 600 °C, the BCC phase transformed to HCP, but when the high-temperature annealed microstructure was irradiated, the BCC transformed into a mixture of HCP and FCC phases. This is attributed to a potential martensitic reaction that was limited in the former due to a high B2 number density. These results reveal pathways to alter phase stability and Ru concentration in the matrix, which can be applied to the design of promising alloys in the high-entropy space.
- 4 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPhase stability of a Zr-Ru BCC+B2 eutectic refractory alloy during annealing and proton irradiation
Alloying refractory metals with Ru is a promising approach to obtain BCC+B2 microstructures. The current paper investigates a simple Zr-Ru binary alloy to gain fundamental insights into the effect of Ru on the phase stability. The composition of interest, 80Zr-20Ru (at.%), is a near-eutectic composition that consists of lamellar BCC and B2 phases. High-temperature annealing of this as-cast microstructure at 1150 °C coarsened the lamellar B2 into a blocky morphology, with a corresponding reduction in B2 number density. Aging at 600 °C transformed the BCC matrix phase into HCP and B2 phases via a divorced eutectoid reaction. This result indicates that the current experimental and computed Zr-Ru phase diagram requires revision. While the untransformed BCC phase exhibited a clear ω formation tendency, the distortions in the diffraction patterns recorded near the BCC-HCP reaction front are inconsistent with the ω displacements and potentially indicate a different displacement wave before transforming to HCP. During proton irradiation at 600 °C, the BCC phase underwent phase transformations depending on the initial microstructure. When the as-cast sample was irradiated at 600 °C, the BCC phase transformed to HCP, but when the high-temperature annealed microstructure was irradiated, the BCC transformed into a mixture of HCP and FCC phases. This is attributed to a potential martensitic reaction that was limited in the former due to a high B2 number density. These results reveal pathways to alter phase stability and Ru concentration in the matrix, which can be applied to the design of promising alloys in the high-entropy space.
- 5 September 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 617
Nanoscale clustering and fission product segregation in irradiated annular U-10Zr fuel
- 5 September 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 617
Nanoscale clustering and fission product segregation in irradiated annular U-10Zr fuel
- 20 January 2025
- Published by Elsevier in Acta Materialia
- Vol. 286
Local chemical ordering of a neutron-irradiated CrFeMnNi compositionally complex alloy
- 20 January 2025
- Published by Elsevier in Acta Materialia
- Vol. 286
Local chemical ordering of a neutron-irradiated CrFeMnNi compositionally complex alloy
- 25 June 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 599
Correlating microstructure and mechanical properties of harvested high dose Zorita light water reactor internals
- 25 June 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 599
Correlating microstructure and mechanical properties of harvested high dose Zorita light water reactor internals
- Open Access
- 29 December 2023
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (1) , 1-13
On the Use of a Cluster Identification Method and a Statistical Approach for Analyzing Atom Probe Tomography Data for GP Zones in Al–Zn–Mg(–Cu) Alloys
Early-stage clustering in two Al–Mg–Zn(–Cu) alloys has been investigated using atom probe tomography and transmission electron microscopy. Cluster identification by the isoposition method and a statistical approach based on the pair correlation function have both been applied to estimate the cluster size, composition, and volume fraction from atom probe data sets. To assess the accuracy of the quantification of clusters of different mean sizes, synthesized virtual data sets were used, accounting for a simulated degraded spatial resolution. The quality of the predictions made by the two complementary methods is discussed, considering the experimental and simulated data sets.
- 29 December 2023
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (1) , 1-13
Open AccessOn the Use of a Cluster Identification Method and a Statistical Approach for Analyzing Atom Probe Tomography Data for GP Zones in Al–Zn–Mg(–Cu) Alloys
Early-stage clustering in two Al–Mg–Zn(–Cu) alloys has been investigated using atom probe tomography and transmission electron microscopy. Cluster identification by the isoposition method and a statistical approach based on the pair correlation function have both been applied to estimate the cluster size, composition, and volume fraction from atom probe data sets. To assess the accuracy of the quantification of clusters of different mean sizes, synthesized virtual data sets were used, accounting for a simulated degraded spatial resolution. The quality of the predictions made by the two complementary methods is discussed, considering the experimental and simulated data sets.