Vasyl Kordan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vasyl Kordan has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
V. Pavlyuk
6 shared publications- Volodymyr Pavlyuk
Department of Inorganic Chemistry, Ivan Franko National University, Kyryla and Mefodiya str., 6, 79005 Lviv, Ukraine
5 shared publications - Khrystyna Khrushchyk
Department of Physical and Colloidal Chemistry, Faculty of Chemistry, Ivan Franko National University of Lviv, 6 Kyryla and Mefodiia Street, 79005 Lviv, Ukraine
4 shared publications - Lidiya M. Boichyshyn
Ivan Franko National University of Lviv, Lviv, Ukraine
4 shared publications - Małgorzata Karolus
Institute of Materials Engineering, Faculty of Science and Technology, University of Silesia, 75 Pułku Piechoty 1a, 41-500 Chorzów, Poland
4 shared publications I. Tarasiuk
Ivan Franko Natl Univ Lviv, Lvov, Ukraine
3 shared publications
Latest Publications
- Open Access
The Influence of Short-Term Isothermal Annealing on Changes in the Surface and the Physical and Chemical Properties of Amorphous Metal Alloy Al87Y4Gd1Ni4Fe4
This study investigates the effect of short-term isothermal annealing at 647 ± 1 K for 5 min on the surface state, electrochemical response, and tribological behavior of the Al87Y4Gd1Ni4Fe4 amorphous alloy. Scanning Kelvin probe measurements revealed a pronounced shift in the contact potential difference and a more spatially coherent distribution of CPD after annealing, indicating substantial modification of the surface electronic state. XPS analysis showed that the relative contribution of oxidized Al increased from approximately 84.4% to 92.9%, whereas the contribution of non-oxide Al species decreased from approximately 15.6% to 7.1%. At the same time, the total surface oxygen concentration decreased and yttrium became enriched in the near-surface region, demonstrating a redistribution of surface chemical states rather than a simple increase in oxidation. Annealing caused only minor changes in surface roughness but markedly improved wear performance: the specific wear rate decreased from 1.917 × 10−3 to 1.234 × 10−3 mm3/(N·m) (approximately 36%), while the maximum wear-track depth decreased from 35.8 to 8.55 μm. In contrast, electrochemical impedance spectroscopy revealed deterioration of the protective properties of the surface layer. The passive-film resistance decreased from 7845 to 4335 Ω·cm2, the charge-transfer resistance from 8692 to 5262 Ω·cm2, and the double-layer CPE exponent ndl from 0.91 to 0.74, indicating increased electrochemical heterogeneity of the interface. Thus, short-term annealing produces a distinct functional trade-off: it substantially improves the tribological performance of the Al87Y4Gd1Ni4Fe4 alloy while simultaneously reducing the effectiveness of its electrochemical surface barrier.
Open AccessThe Influence of Short-Term Isothermal Annealing on Changes in the Surface and the Physical and Chemical Properties of Amorphous Metal Alloy Al87Y4Gd1Ni4Fe4
This study investigates the effect of short-term isothermal annealing at 647 ± 1 K for 5 min on the surface state, electrochemical response, and tribological behavior of the Al87Y4Gd1Ni4Fe4 amorphous alloy. Scanning Kelvin probe measurements revealed a pronounced shift in the contact potential difference and a more spatially coherent distribution of CPD after annealing, indicating substantial modification of the surface electronic state. XPS analysis showed that the relative contribution of oxidized Al increased from approximately 84.4% to 92.9%, whereas the contribution of non-oxide Al species decreased from approximately 15.6% to 7.1%. At the same time, the total surface oxygen concentration decreased and yttrium became enriched in the near-surface region, demonstrating a redistribution of surface chemical states rather than a simple increase in oxidation. Annealing caused only minor changes in surface roughness but markedly improved wear performance: the specific wear rate decreased from 1.917 × 10−3 to 1.234 × 10−3 mm3/(N·m) (approximately 36%), while the maximum wear-track depth decreased from 35.8 to 8.55 μm. In contrast, electrochemical impedance spectroscopy revealed deterioration of the protective properties of the surface layer. The passive-film resistance decreased from 7845 to 4335 Ω·cm2, the charge-transfer resistance from 8692 to 5262 Ω·cm2, and the double-layer CPE exponent ndl from 0.91 to 0.74, indicating increased electrochemical heterogeneity of the interface. Thus, short-term annealing produces a distinct functional trade-off: it substantially improves the tribological performance of the Al87Y4Gd1Ni4Fe4 alloy while simultaneously reducing the effectiveness of its electrochemical surface barrier.
- 1 October 2026
- Published by Lviv Polytechnic National University in Infocommunication technologies and electronic engineering
- Vol. 6 (2) , 192-201
DESIGN RULES FOR TUNING THE NANOPARTICLES PLASMONIC RESPONSE: NUMERICAL ANALYSIS OF MATERIAL, MORPHOLOGY, SIZE, AND DIELECTRIC ENVIRONMENT
Localized surface plasmon resonance (LSPR) in metal nanoparticles is determined by the combination of their structural, geometric, and optical parameters, which offers extensive possibilities for controlling the spectral response of plasmonic structures. This study presents a comprehensive numerical analysis of the influence of the material, size, geometric shape, and dielectric parameters of the nanoparticle environment on the spectral position, intensity, and mode structure of LSPR. Numerical and analytical approaches were used to model the optical response, enabling a systematic comparison of the plasmonic characteristics of nanoparticles with different parameters. It has been established that the nanoparticle material determines the fundamental spectral region of plasmon resonance formation and the nature of its spectral profile. A change in size leads to a shift in the resonant wavelength and a change in the intensity of the optical response, with the nature of these changes depending significantly on the optical properties of the material. It is shown that geometric shape is an effective mechanism for controlling LSPR: decreasing symmetry and increasing geometric anisotropy contribute to a long-wavelength shift of the resonance and the appearance of additional plasmon modes. The presence of sharp edges and vertices in nanoparticle geometry leads to a non-uniform surface charge distribution and enhanced electromagnetic field localization, which is particularly important for applications based on local field enhancement. The influence of the dielectric properties of the surrounding medium was investigated separately. A systematic long-wavelength shift of the LSPR with increasing refractive index has been observed, with the magnitude of spectral sensitivity depending significantly on the nanoparticle material. The obtained results demonstrate that the spectral response of plasmonic nanoparticles can be tuned through a combined choice of material, size, morphology, and dielectric environment. The established relationships can serve as practical principles for designing plasmonic nanostructures with specific optical characteristics for use in optical and refractometric sensors, optoelectronic structures, and functional nanocomposites.
- 1 October 2026
- Published by Lviv Polytechnic National University in Infocommunication technologies and electronic engineering
- Vol. 6 (2) , 192-201
DESIGN RULES FOR TUNING THE NANOPARTICLES PLASMONIC RESPONSE: NUMERICAL ANALYSIS OF MATERIAL, MORPHOLOGY, SIZE, AND DIELECTRIC ENVIRONMENT
Localized surface plasmon resonance (LSPR) in metal nanoparticles is determined by the combination of their structural, geometric, and optical parameters, which offers extensive possibilities for controlling the spectral response of plasmonic structures. This study presents a comprehensive numerical analysis of the influence of the material, size, geometric shape, and dielectric parameters of the nanoparticle environment on the spectral position, intensity, and mode structure of LSPR. Numerical and analytical approaches were used to model the optical response, enabling a systematic comparison of the plasmonic characteristics of nanoparticles with different parameters. It has been established that the nanoparticle material determines the fundamental spectral region of plasmon resonance formation and the nature of its spectral profile. A change in size leads to a shift in the resonant wavelength and a change in the intensity of the optical response, with the nature of these changes depending significantly on the optical properties of the material. It is shown that geometric shape is an effective mechanism for controlling LSPR: decreasing symmetry and increasing geometric anisotropy contribute to a long-wavelength shift of the resonance and the appearance of additional plasmon modes. The presence of sharp edges and vertices in nanoparticle geometry leads to a non-uniform surface charge distribution and enhanced electromagnetic field localization, which is particularly important for applications based on local field enhancement. The influence of the dielectric properties of the surrounding medium was investigated separately. A systematic long-wavelength shift of the LSPR with increasing refractive index has been observed, with the magnitude of spectral sensitivity depending significantly on the nanoparticle material. The obtained results demonstrate that the spectral response of plasmonic nanoparticles can be tuned through a combined choice of material, size, morphology, and dielectric environment. The established relationships can serve as practical principles for designing plasmonic nanostructures with specific optical characteristics for use in optical and refractometric sensors, optoelectronic structures, and functional nanocomposites.
- Open Access
Thermally Initiated Structural Transformations in the Temperature Range (624–643) ± 1 K for Amorphous Metal Alloy Al87Y4Gd1Ni8 and Influence on Mechanical Properties
Amorphous metal alloys (AMAs) are metastable materials that are characterized by good mechanical properties and corrosion properties. It is known that with certain thermal modifications, these properties improve or lose their value. The purpose of this research work is to investigate the optimal conditions of thermal modification that improve the mechanical properties of this alloy. The DSC method established the temperatures of phase transitions in the temperature range of 624–643 K, which correspond to the following processes: crystal nucleation (T1 = 624 ± 1 K), growth (T2 = 633 ± 1 K), and stable crystallization (T3 = 643 ± 1 K). The XRD and TEM/HREM methods revealed structural changes in the amorphous matrix as a result of thermal modification. As a result of isothermal annealing for 2 min. at temperatures T1, T2, T3, a solid solution based on aluminum and a thermally stable compound Al19Ni5(Y,Gd)3 were formed. The equation for the transformation of an amorphous matrix AMA Al87Y4Gd1Ni8 in the temperature range (624–643) ± 1 K during isothermal 2 min annealing is given by: Am → Am′resid+ solid solution Al(X) → Am′(enriched REE) + solid solution Al(X) + nano-Al19Ni5(Y,Gd)3 → Am′(enriched REE) + solid solution Al(X) + nano-Al19Ni5(Y,Gd)3. The Oliver–Pharr method established that AMAs annealed at temperatures T1 and T2 have microhardness indicators 5–9 times higher than amorphous samples; however, the material loses its elasticity under such thermal deformation conditions.
Open AccessThermally Initiated Structural Transformations in the Temperature Range (624–643) ± 1 K for Amorphous Metal Alloy Al87Y4Gd1Ni8 and Influence on Mechanical Properties
Amorphous metal alloys (AMAs) are metastable materials that are characterized by good mechanical properties and corrosion properties. It is known that with certain thermal modifications, these properties improve or lose their value. The purpose of this research work is to investigate the optimal conditions of thermal modification that improve the mechanical properties of this alloy. The DSC method established the temperatures of phase transitions in the temperature range of 624–643 K, which correspond to the following processes: crystal nucleation (T1 = 624 ± 1 K), growth (T2 = 633 ± 1 K), and stable crystallization (T3 = 643 ± 1 K). The XRD and TEM/HREM methods revealed structural changes in the amorphous matrix as a result of thermal modification. As a result of isothermal annealing for 2 min. at temperatures T1, T2, T3, a solid solution based on aluminum and a thermally stable compound Al19Ni5(Y,Gd)3 were formed. The equation for the transformation of an amorphous matrix AMA Al87Y4Gd1Ni8 in the temperature range (624–643) ± 1 K during isothermal 2 min annealing is given by: Am → Am′resid+ solid solution Al(X) → Am′(enriched REE) + solid solution Al(X) + nano-Al19Ni5(Y,Gd)3 → Am′(enriched REE) + solid solution Al(X) + nano-Al19Ni5(Y,Gd)3. The Oliver–Pharr method established that AMAs annealed at temperatures T1 and T2 have microhardness indicators 5–9 times higher than amorphous samples; however, the material loses its elasticity under such thermal deformation conditions.
- Open Access
The Effect of Short-Term Annealing of the Amorphous Metal Alloy Al87Y4Gd1Ni8 on Surface Morphology and Electrochemical Properties
Amorphous metal alloys (AMAs) are characterized by good mechanical and electrochemical properties. However, due to crystallization processes occurring at higher temperatures (Ta ˃ 600 K), these properties may deteriorate. The aim of this work was to investigate the effects of short-term annealing at T3 = 611 ± 1 K and to determine the risks of such thermal modifications for the electrochemical properties of the material. A comprehensive analysis shows that short-term isothermal annealing (5 min) of the amorphous metal alloy Al87Y4Gd1Ni8 at a temperature of 611 ± 1 K improves the tribological properties of the material. However, it has been established that heat treatment for 5 min is optimal and leads to temporary thickening of the film and the formation of an almost ideal double layer, but annealing for 15–60 min negatively affects the electrochemical properties of this material, indicating a decrease in the protective properties of the passivating layers.
Open AccessThe Effect of Short-Term Annealing of the Amorphous Metal Alloy Al87Y4Gd1Ni8 on Surface Morphology and Electrochemical Properties
Amorphous metal alloys (AMAs) are characterized by good mechanical and electrochemical properties. However, due to crystallization processes occurring at higher temperatures (Ta ˃ 600 K), these properties may deteriorate. The aim of this work was to investigate the effects of short-term annealing at T3 = 611 ± 1 K and to determine the risks of such thermal modifications for the electrochemical properties of the material. A comprehensive analysis shows that short-term isothermal annealing (5 min) of the amorphous metal alloy Al87Y4Gd1Ni8 at a temperature of 611 ± 1 K improves the tribological properties of the material. However, it has been established that heat treatment for 5 min is optimal and leads to temporary thickening of the film and the formation of an almost ideal double layer, but annealing for 15–60 min negatively affects the electrochemical properties of this material, indicating a decrease in the protective properties of the passivating layers.
- Open Access
- 6 March 2025
- Published by Stepan Gzhytskyi National University of Veterinary Medicine and Biotechnologies Lviv in Scientific Messenger of LNU of Veterinary Medicine and Biotechnologies. Series: Food Technologies
- Vol. 27 (103) , 56-60
Evaluation of the corrosion resistance of cobalt-based amorphous alloys in an alkaline solution
Cobalt-based amorphous alloys have high corrosion resistance in alkaline solutions due to several key factors. In particular, amorphous alloys do not have a crystal lattice, which excludes the presence of main places for local corrosion. It also significantly reduces the likelihood of formation of microgalvanic pairs, which are the cause of corrosive destruction. Cobalt amorphous alloys often contain chromium, boron, phosphorus and molybdenum, which contribute to the formation of a protective passive film on the surface of the material. In alkaline environments, this film (metal oxides and hydroxides) is stable, which provides durability and resistance to corrosion. Since cobalt and its oxides are highly stable in alkaline environments, this can contribute to electrocatalytic processes. Such alloys are promising for use in electrochemical devices (batteries, fuel cells, etc.). In alkaline environments, due to the high content of cobalt and additional alloying elements, amorphous alloys show special resistance to pitting and crevice corrosion, which is especially important for industrial applications. Due to these properties, amorphous cobalt alloys are used in anti-corrosion coatings, medical implants, as well as in electrochemical and magnetic devices. In the case of using cobalt amorphous alloys as catalysts for the release of hydrogen from alkaline solutions, the corrosion resistance of ribbon amorphous alloys Co72,0Fe5,0Si11,0B12,0, Co72,0Cr5,0Si11,0B12,0, Co70Fe2,5Cr4,5Si11B12 in a 1.0 M aqueous solution of KOH was evaluated for the first time. Electrochemical characteristics of alloys at different speeds of potential scanning were determined.
- 6 March 2025
- Published by Stepan Gzhytskyi National University of Veterinary Medicine and Biotechnologies Lviv in Scientific Messenger of LNU of Veterinary Medicine and Biotechnologies. Series: Food Technologies
- Vol. 27 (103) , 56-60
Open AccessEvaluation of the corrosion resistance of cobalt-based amorphous alloys in an alkaline solution
Cobalt-based amorphous alloys have high corrosion resistance in alkaline solutions due to several key factors. In particular, amorphous alloys do not have a crystal lattice, which excludes the presence of main places for local corrosion. It also significantly reduces the likelihood of formation of microgalvanic pairs, which are the cause of corrosive destruction. Cobalt amorphous alloys often contain chromium, boron, phosphorus and molybdenum, which contribute to the formation of a protective passive film on the surface of the material. In alkaline environments, this film (metal oxides and hydroxides) is stable, which provides durability and resistance to corrosion. Since cobalt and its oxides are highly stable in alkaline environments, this can contribute to electrocatalytic processes. Such alloys are promising for use in electrochemical devices (batteries, fuel cells, etc.). In alkaline environments, due to the high content of cobalt and additional alloying elements, amorphous alloys show special resistance to pitting and crevice corrosion, which is especially important for industrial applications. Due to these properties, amorphous cobalt alloys are used in anti-corrosion coatings, medical implants, as well as in electrochemical and magnetic devices. In the case of using cobalt amorphous alloys as catalysts for the release of hydrogen from alkaline solutions, the corrosion resistance of ribbon amorphous alloys Co72,0Fe5,0Si11,0B12,0, Co72,0Cr5,0Si11,0B12,0, Co70Fe2,5Cr4,5Si11B12 in a 1.0 M aqueous solution of KOH was evaluated for the first time. Electrochemical characteristics of alloys at different speeds of potential scanning were determined.
- 1 January 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 81-82
Electrochemical Properties of Ba2HoCu3O7
The ceramic phase Ba2HoCu3O7 was tested as potential cathode material of a lithium-ion battery. A single-phase polycrystalline sample was synthesized via solid-state reaction and characterized by XRD, SEM, and EDX. Electrochemical lithiation in a Ba₂HoCu₃O₇ cell preserved the initial structure with a volume expansion of ΔV/V = 0.21%. Up to 0.63 Li per formula unit was intercalated, and the battery showed cycling stability over 50 cycles.
- 1 January 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications)
- p. 81-82
Electrochemical Properties of Ba2HoCu3O7
The ceramic phase Ba2HoCu3O7 was tested as potential cathode material of a lithium-ion battery. A single-phase polycrystalline sample was synthesized via solid-state reaction and characterized by XRD, SEM, and EDX. Electrochemical lithiation in a Ba₂HoCu₃O₇ cell preserved the initial structure with a volume expansion of ΔV/V = 0.21%. Up to 0.63 Li per formula unit was intercalated, and the battery showed cycling stability over 50 cycles.
- Open Access
- 1 January 2025
- Published by Ivan Franko National University of Lviv in Visnyk of the Lviv University. Series Chemistry
- Vol. 66 (1)
Electrochemical synthesis of the LixCa0.5Pr0.5FeO3 phase
ЕЛЕКТРОХІМІЧНИЙ СИНТЕЗ ФАЗИ Li x Ca 0,5 Pr 0,5 FeO 3
- 1 January 2025
- Published by Ivan Franko National University of Lviv in Visnyk of the Lviv University. Series Chemistry
- Vol. 66 (1)
Open AccessElectrochemical synthesis of the LixCa0.5Pr0.5FeO3 phase
ЕЛЕКТРОХІМІЧНИЙ СИНТЕЗ ФАЗИ Li x Ca 0,5 Pr 0,5 FeO 3
- Open Access
- 18 December 2024
- Published by Swiss Chemical Society in Chimia
- Vol. 78 (12) , 869-877
Intermetallic Materials for High-Capacity Hydrogen Storage Systems
In this article, we provide an overview of hydrogen storage materials, taking our previous results as examples. Towards the end of the paper, we present a case study in order to highlight the effects of substitutional alloying, compositional additives, and nanostructuring on the hydrogen sorption properties of magnesium-based intermetallics. Specifically, partial substitution of Mg by Li and d-elements by p-elements leads to structural changes, inducing disorder and the formation of high-entropy alloys. Our approach showcases the methodology to enhance the H2-capacity and to provide a positive boost to the H2-storage performance, including lower temperatures of H2 desorption, better thermodynamics and kinetics, lower temperatures of hydrogen uptake/ release for Metal-Hydride Hydrogen Storage (MHHS) systems and higher capacity of anodes for Metal-Hydride batteries (MHB) together with lower prices of raw materials.
- 18 December 2024
- Published by Swiss Chemical Society in Chimia
- Vol. 78 (12) , 869-877
Open AccessIntermetallic Materials for High-Capacity Hydrogen Storage Systems
In this article, we provide an overview of hydrogen storage materials, taking our previous results as examples. Towards the end of the paper, we present a case study in order to highlight the effects of substitutional alloying, compositional additives, and nanostructuring on the hydrogen sorption properties of magnesium-based intermetallics. Specifically, partial substitution of Mg by Li and d-elements by p-elements leads to structural changes, inducing disorder and the formation of high-entropy alloys. Our approach showcases the methodology to enhance the H2-capacity and to provide a positive boost to the H2-storage performance, including lower temperatures of H2 desorption, better thermodynamics and kinetics, lower temperatures of hydrogen uptake/ release for Metal-Hydride Hydrogen Storage (MHHS) systems and higher capacity of anodes for Metal-Hydride batteries (MHB) together with lower prices of raw materials.