Jianchun Weng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jianchun Weng has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Bin Lu
College of Marine Equipment and Mechanical Engineering and Xiamen Key Lab of Marine Corrosion and Smart Protective Materials, Jimei University, Xiamen 361021, China
2 shared publications - Bo Li
Jimei University, Xiamen, Xiamen, 361021, CHINA
2 shared publications - Ding-Rong Deng
College of Marine Equipment and Mechanical Engineering Key Laboratory of Energy Cleaning Utilization Development Cleaning Combustion and Energy Utilization Research Center of Fujian Province Xiamen Key Laboratory of Marine Corrosion and Smart Protective Materials Jimei University Xiamen Fujian 361021 P. R. China
2 shared publications - Guifang Li
College of Marine Equipment and Mechanical Engineering and Xiamen Key Lab of Marine Corrosion and Smart Protective Materials, Jimei University, Xiamen 361021, China
2 shared publications - Junying Chen
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China
2 shared publications - Qi-Hui Wu
Xiamen Key Lab of Marine Corrosion and Smart Protective Materials, College of Mechanical and Energy Engineering, Jimei University, Xiamen 361021, P. R. China
2 shared publications
Latest Publications
- Open Access
Application of Li6.4La3Zr1.45Ta0.5Mo0.05O12/PEO Composite Solid Electrolyte in High-Performance Lithium Batteries
Replacing the flammable liquid electrolytes with solid ones has been considered to be the most effective way to improve the safety of the lithium batteries. However, the solid electrolytes often suffer from low ionic conductivity and poor rate capability due to their relatively stable molecular/atomic architectures. In this study, we report a composite solid electrolyte, in which polyethylene oxide (PEO) is the matrix and Li6.4La3Zr1.45Ta0.5Mo0.05O12 (LLZTMO) and Li6.4La3Zr1.4Ta0.6O12 (LLZTO) are the fillers. Ta/Mo co-doping can further promote the ion transport capacity in the electrolyte. The synthesized composite electrolytes exhibit high thermal stability (up to 413 °C) and good ionic conductivity (LLZTMO–PEO 2.00 × 10−4 S·cm−1, LLZTO–PEO 1.53 × 10−4 S·cm−1) at 35 °C. Compared with a pure PEO electrolyte, whose ionic conductivity is in the range of 10−7~10−6 S·cm−1, the ionic conductivity of composite solid electrolytes is greatly improved. The full cell assembled with LiFePO4 as the positive electrode exhibits excellent rate performance and good cycling stability, indicating that prepared solid electrolytes have great potential applications in lithium batteries.
Open AccessApplication of Li6.4La3Zr1.45Ta0.5Mo0.05O12/PEO Composite Solid Electrolyte in High-Performance Lithium Batteries
Replacing the flammable liquid electrolytes with solid ones has been considered to be the most effective way to improve the safety of the lithium batteries. However, the solid electrolytes often suffer from low ionic conductivity and poor rate capability due to their relatively stable molecular/atomic architectures. In this study, we report a composite solid electrolyte, in which polyethylene oxide (PEO) is the matrix and Li6.4La3Zr1.45Ta0.5Mo0.05O12 (LLZTMO) and Li6.4La3Zr1.4Ta0.6O12 (LLZTO) are the fillers. Ta/Mo co-doping can further promote the ion transport capacity in the electrolyte. The synthesized composite electrolytes exhibit high thermal stability (up to 413 °C) and good ionic conductivity (LLZTMO–PEO 2.00 × 10−4 S·cm−1, LLZTO–PEO 1.53 × 10−4 S·cm−1) at 35 °C. Compared with a pure PEO electrolyte, whose ionic conductivity is in the range of 10−7~10−6 S·cm−1, the ionic conductivity of composite solid electrolytes is greatly improved. The full cell assembled with LiFePO4 as the positive electrode exhibits excellent rate performance and good cycling stability, indicating that prepared solid electrolytes have great potential applications in lithium batteries.
- Open Access
- 2 November 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (12) , 126404
Deposition of diamond films by microwave plasma CVD on 4H-SiC substrates
Diamond films were deposited on 4H-SiC substrates by microwave plasma chemical vapor deposition (MPCVD). The substrate pretreatment method of electrostatic adsorption of seed crystals by nanodiamond suspensions was used, and the nucleation density of diamond on the substrate surface reached 1010/cm2 compared with ultrasonic seed crystals of diamond micro-powder suspensions, and continuous dense diamond films were formed in a shorter growth time. Scanning electron microscopy and Raman spectroscopy were used to characterize the changes of diamond grain morphology and quality with methane concentration, deposition time and substrate temperature during the growth process. The experimental results show that the methane concentration, deposition time and substrate temperature are the key factors affecting the grain shape and quality of diamond. And the best quality of diamond film is obtained at 850 °C substrate temperature.
- 2 November 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (12) , 126404
Open AccessDeposition of diamond films by microwave plasma CVD on 4H-SiC substrates
Diamond films were deposited on 4H-SiC substrates by microwave plasma chemical vapor deposition (MPCVD). The substrate pretreatment method of electrostatic adsorption of seed crystals by nanodiamond suspensions was used, and the nucleation density of diamond on the substrate surface reached 1010/cm2 compared with ultrasonic seed crystals of diamond micro-powder suspensions, and continuous dense diamond films were formed in a shorter growth time. Scanning electron microscopy and Raman spectroscopy were used to characterize the changes of diamond grain morphology and quality with methane concentration, deposition time and substrate temperature during the growth process. The experimental results show that the methane concentration, deposition time and substrate temperature are the key factors affecting the grain shape and quality of diamond. And the best quality of diamond film is obtained at 850 °C substrate temperature.
- Open Access
Synthesis of Low-Cost and High-Performance Dual-Atom Doped Carbon-Based Materials with a Simple Green Route as Anodes for Sodium-Ion Batteries
Sodium-ion batteries (SIBs) are promising alternatives to replace lithium-ion batteries as future energy storage batteries because of their abundant sodium resources, low cost, and high charging efficiency. In order to match the high energy capacity and density, designing an atomically doped carbonous material as the anode is presently one of the important strategies to commercialize SIBs. In this work, we report the preparation of high-performance dual-atom-doped carbon (C) materials using low-cost corn starch and thiourea (CH4N2S) as the precursors. The electronegativity and radii of the doped atoms and C are different, which can vary the embedding properties of sodium ions (Na+) into/on C. As sulfur (S) can effectively expand the layer spacing, it provides more channels for embedding and de-embedding Na+. The synergistic effect of N and S co-doping can remarkably boost the performance of SIBs. The capacity is preserved at 400 mAh g −1 after 200 cycles at 500 mA g−1; more notably, the initial Coulombic efficiency is 81%. Even at a high rate of high current of 10 A g−1, the cell capacity can still reach 170 mAh g−1. More importantly, after 3000 cycles at 1 A g−1, the capacity decay is less than 0.003% per cycle, which demonstrates its excellent electrochemical performance. These results indicate that high-performance carbon materials can be prepared using low-cost corn starch and thiourea.
Open AccessSynthesis of Low-Cost and High-Performance Dual-Atom Doped Carbon-Based Materials with a Simple Green Route as Anodes for Sodium-Ion Batteries
Sodium-ion batteries (SIBs) are promising alternatives to replace lithium-ion batteries as future energy storage batteries because of their abundant sodium resources, low cost, and high charging efficiency. In order to match the high energy capacity and density, designing an atomically doped carbonous material as the anode is presently one of the important strategies to commercialize SIBs. In this work, we report the preparation of high-performance dual-atom-doped carbon (C) materials using low-cost corn starch and thiourea (CH4N2S) as the precursors. The electronegativity and radii of the doped atoms and C are different, which can vary the embedding properties of sodium ions (Na+) into/on C. As sulfur (S) can effectively expand the layer spacing, it provides more channels for embedding and de-embedding Na+. The synergistic effect of N and S co-doping can remarkably boost the performance of SIBs. The capacity is preserved at 400 mAh g −1 after 200 cycles at 500 mA g−1; more notably, the initial Coulombic efficiency is 81%. Even at a high rate of high current of 10 A g−1, the cell capacity can still reach 170 mAh g−1. More importantly, after 3000 cycles at 1 A g−1, the capacity decay is less than 0.003% per cycle, which demonstrates its excellent electrochemical performance. These results indicate that high-performance carbon materials can be prepared using low-cost corn starch and thiourea.
- Open Access
The Effects of Ultrasonic Impact Modification on the Surface Quality of 20CrNiMo Carburized Steel
Ultra-high residual compressive stress can be introduced via the ultrasonic impact on the basis of transformation hardening, and further enhance the overall performance of 20CrNiMo carburized steel. In order to achieve the best surface quality of 20CrNiMo carburized steel, ultrasonic impact modification testing with varying static loads (900 N, 1200 N, and 1500 N) and rounds (1, 3, and 6) was conducted. By characterizing microhardness, microstructure, the surface roughness and residual compressive stress, the influence of ultrasonic impact modification parameters on its surface quality were analyzed. The experimental results indicated that the static loads and rounds of ultrasonic impact modification had a significant impact on the surface quality. The best surface quality could be obtained after six rounds of ultrasonic impact modification under a static load of 1200 N. In addition, the surface roughness decreased from 0.40 μm to 0.04 μm, the surface microhardness increased from 679 HV0.1 to 1086 HV0.1, and the maximum residual compressive stress of 1195.36 MPa was formed. Furthermore, the surface quality would deteriorate when the static load and ultrasonic impact rounds were increased.
Open AccessThe Effects of Ultrasonic Impact Modification on the Surface Quality of 20CrNiMo Carburized Steel
Ultra-high residual compressive stress can be introduced via the ultrasonic impact on the basis of transformation hardening, and further enhance the overall performance of 20CrNiMo carburized steel. In order to achieve the best surface quality of 20CrNiMo carburized steel, ultrasonic impact modification testing with varying static loads (900 N, 1200 N, and 1500 N) and rounds (1, 3, and 6) was conducted. By characterizing microhardness, microstructure, the surface roughness and residual compressive stress, the influence of ultrasonic impact modification parameters on its surface quality were analyzed. The experimental results indicated that the static loads and rounds of ultrasonic impact modification had a significant impact on the surface quality. The best surface quality could be obtained after six rounds of ultrasonic impact modification under a static load of 1200 N. In addition, the surface roughness decreased from 0.40 μm to 0.04 μm, the surface microhardness increased from 679 HV0.1 to 1086 HV0.1, and the maximum residual compressive stress of 1195.36 MPa was formed. Furthermore, the surface quality would deteriorate when the static load and ultrasonic impact rounds were increased.
- Open Access
Effect of Laser Shock Peening on the Fatigue Life of 1Cr12Ni3Mo2VN Steel for Steam Turbine Blades
In the present study, laser shock peening (LSP) was employed to enhance the rotating bending fatigue life of 1Cr12Ni3Mo2VN martensitic stainless steel used in steam turbine blades, addressing the issue of insufficient fatigue performance in these components. The aim of this study was to investigate the effect of LSP on the microhardness, residual stress, and rotating bending fatigue life of 1Cr12Ni3Mo2VN steel samples. The microhardness of LSP-treated samples was increased by 10.5% (LSP-3J sample) and 15.3% (LSP-4J sample), respectively, compared to high-frequency hardening samples. The residual compressive stress of the LSP-4J sample was the largest, reaching −689 MPa, and the affected layer depth was about 800 μm. Fatigue tests showed that the number of cycles at the fracture point for the LSP-3J and LSP-4J samples increased by 163% and 233%, respectively. The fatigue fracture morphology of the four samples showed that the microhardness and residual compressive stress distribution introduced by LSP could effectively inhibit the initiation of surface cracks, slow down the crack growth rate, and improve the rotating bending fatigue life of 1Cr12Ni3Mo2VN.
Open AccessEffect of Laser Shock Peening on the Fatigue Life of 1Cr12Ni3Mo2VN Steel for Steam Turbine Blades
In the present study, laser shock peening (LSP) was employed to enhance the rotating bending fatigue life of 1Cr12Ni3Mo2VN martensitic stainless steel used in steam turbine blades, addressing the issue of insufficient fatigue performance in these components. The aim of this study was to investigate the effect of LSP on the microhardness, residual stress, and rotating bending fatigue life of 1Cr12Ni3Mo2VN steel samples. The microhardness of LSP-treated samples was increased by 10.5% (LSP-3J sample) and 15.3% (LSP-4J sample), respectively, compared to high-frequency hardening samples. The residual compressive stress of the LSP-4J sample was the largest, reaching −689 MPa, and the affected layer depth was about 800 μm. Fatigue tests showed that the number of cycles at the fracture point for the LSP-3J and LSP-4J samples increased by 163% and 233%, respectively. The fatigue fracture morphology of the four samples showed that the microhardness and residual compressive stress distribution introduced by LSP could effectively inhibit the initiation of surface cracks, slow down the crack growth rate, and improve the rotating bending fatigue life of 1Cr12Ni3Mo2VN.
- Open Access
Cutting Performance of Multicomponent AlTiZrN-Coated Cemented Carbide (YG8) Tools during Milling of High-Chromium Cast Iron
In order to improve the cutting performance of cemented-carbide (YG8) tools during the milling of high-chromium cast iron, AlTiZrN coating was deposited on the surface of YG8 samples and milling tools by physical vapor deposition (PVD) technology. The micromorphology and mechanical properties of the coating were studied by the experimental method, and the cutting performance of the coated tools was tested by a milling machining center. The results show that the AlTiZrN coating presents the face-centered cubic (fcc) structure of TiN. The average microhardness is 3887 HV0.05. The bonding strength between the coating and the substrate meets the standard HF3 and is up to the requirements. The coefficient of friction (COF) of the coating is about 0.32. AlTiZrN coating can significantly improve the life of cemented-carbide tools. At cutting speeds of 85, 105, and 125 mm/min, the lives of the AlTiZrN-coated tools increased by 20.7%, 22.4%, and 35.2%, respectively, compared with the uncoated tools. Under the same cutting condition, AlTiZrN-coated tools have better cutting and chip-breaking performance than uncoated tools. With the increase in cutting speed, the workpiece chips produced by AlTiZrN-coated tools are smaller and more uniform, and the scratches on the machined surface are smoother. Therefore, at higher cutting speeds, AlTiZrN-coated tools have more advantages in life and cutting performance than that of uncoated tools. During the cutting process, the wear mechanisms of the AlTiZrN-coated tools mainly included friction, oxidation, and bonding, while oxidation and bonding wear were the main wear mechanisms in the later stage of wear.
Open AccessCutting Performance of Multicomponent AlTiZrN-Coated Cemented Carbide (YG8) Tools during Milling of High-Chromium Cast Iron
In order to improve the cutting performance of cemented-carbide (YG8) tools during the milling of high-chromium cast iron, AlTiZrN coating was deposited on the surface of YG8 samples and milling tools by physical vapor deposition (PVD) technology. The micromorphology and mechanical properties of the coating were studied by the experimental method, and the cutting performance of the coated tools was tested by a milling machining center. The results show that the AlTiZrN coating presents the face-centered cubic (fcc) structure of TiN. The average microhardness is 3887 HV0.05. The bonding strength between the coating and the substrate meets the standard HF3 and is up to the requirements. The coefficient of friction (COF) of the coating is about 0.32. AlTiZrN coating can significantly improve the life of cemented-carbide tools. At cutting speeds of 85, 105, and 125 mm/min, the lives of the AlTiZrN-coated tools increased by 20.7%, 22.4%, and 35.2%, respectively, compared with the uncoated tools. Under the same cutting condition, AlTiZrN-coated tools have better cutting and chip-breaking performance than uncoated tools. With the increase in cutting speed, the workpiece chips produced by AlTiZrN-coated tools are smaller and more uniform, and the scratches on the machined surface are smoother. Therefore, at higher cutting speeds, AlTiZrN-coated tools have more advantages in life and cutting performance than that of uncoated tools. During the cutting process, the wear mechanisms of the AlTiZrN-coated tools mainly included friction, oxidation, and bonding, while oxidation and bonding wear were the main wear mechanisms in the later stage of wear.
- Open Access
- 6 November 2020
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 327, 02002
Study on polishing slurry of hydrogen peroxide-oxalic acid in CMP 304 stainless steel
Stainless steel will become the substrate material of the flexible display, requirements of the flexible substrate in the surface quality and performance are very strict. Chemical mechanical polishing (CMP) is one of the most appropriate technologies to achieve the surface processing of ultra-thin stainless-steel flexible display substrate with ultra-smooth and damage-free. In this paper, the design of CMP slurry of 304 stainless steel on the hydrogen peroxide-oxalic acid type was proposed. Through experiment and analysis, the basic ingredients of CMP slurry was obtained. The research results showed that the hydrogen peroxide can increase the hydrophilicity of the stainless steel surface, and the Fenton type Haber-Weiss reaction can occur on the surface of the fresh metal substrate of stainless steel. The trivalent iron ions generated by the Fenton type reaction combined with oxygen to generate iron oxide and promoted the removal of the surface material. Under acidic conditions, the oxalic acid can decrease the stability of the oxide film on the stainless steel surface, promote the diffusion of oxygen into the metal interface, improve the oxygen reduction reaction, and increase the material removal rate. The results will provide an important reference for the next researching the CMP slurry of 304 stainless steel.
- 6 November 2020
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 327, 02002
Open AccessStudy on polishing slurry of hydrogen peroxide-oxalic acid in CMP 304 stainless steel
Stainless steel will become the substrate material of the flexible display, requirements of the flexible substrate in the surface quality and performance are very strict. Chemical mechanical polishing (CMP) is one of the most appropriate technologies to achieve the surface processing of ultra-thin stainless-steel flexible display substrate with ultra-smooth and damage-free. In this paper, the design of CMP slurry of 304 stainless steel on the hydrogen peroxide-oxalic acid type was proposed. Through experiment and analysis, the basic ingredients of CMP slurry was obtained. The research results showed that the hydrogen peroxide can increase the hydrophilicity of the stainless steel surface, and the Fenton type Haber-Weiss reaction can occur on the surface of the fresh metal substrate of stainless steel. The trivalent iron ions generated by the Fenton type reaction combined with oxygen to generate iron oxide and promoted the removal of the surface material. Under acidic conditions, the oxalic acid can decrease the stability of the oxide film on the stainless steel surface, promote the diffusion of oxygen into the metal interface, improve the oxygen reduction reaction, and increase the material removal rate. The results will provide an important reference for the next researching the CMP slurry of 304 stainless steel.