Rui-Guo Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rui-Guo Yan has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Wenjing Wang
Beijing Jiaotong University
4 shared publications - Xi-Shu Wang
Department of Engineering Mechanics, School of Aerospace Engineering, Tsinghua University, Beijing 100084, China
4 shared publications Wei Shan
3 shared publicationsRan Ding
2 shared publicationsWen-Jing Wang
2 shared publicationsAn Liu
Department of Engineering Mechanics Tsinghua University Beijing China
1 shared publication
Latest Publications
- 20 September 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 215
Dynamic-stress-based fatigue damage evaluation of bogie frames using a two-stage state-space reconstruction model
- 20 September 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 215
Dynamic-stress-based fatigue damage evaluation of bogie frames using a two-stage state-space reconstruction model
- 18 September 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (12) , 5563-5581
Bandwidth‐Corrected Dirlik Method for Vibration Fatigue Damage Assessment of Critical Structures in High‐Speed Trains
Frequency‐domain methods enable efficient vibration fatigue assessment of high‐speed train structures under stationary Gaussian assumptions, but their accuracy remains sensitive to the bandwidth characteristics of the stress power spectral density. Based on field‐test stress measurements, stationary Gaussian stress segments were extracted, and the corresponding time‐domain rainflow‐counting damage was calculated as the benchmark for evaluating frequency‐domain prediction accuracy. A practical 5RMS stress‐amplitude boundary was proposed as an engineering upper integration bound for fatigue‐damage calculation. A bandwidth‐corrected Dirlik method was further developed by introducing a bandwidth‐dependent correction coefficient into the original formulation. The resulting method retains the probabilistic structure and computational efficiency of the original Dirlik model, while improving bandwidth adaptability and reducing the maximum prediction error from approximately 50% to below 10%. Validation using representative train‐structure stress responses confirms the applicability of the proposed method to stationary Gaussian and PSD‐based fatigue assessment scenarios.
- 18 September 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (12) , 5563-5581
Bandwidth‐Corrected Dirlik Method for Vibration Fatigue Damage Assessment of Critical Structures in High‐Speed Trains
Frequency‐domain methods enable efficient vibration fatigue assessment of high‐speed train structures under stationary Gaussian assumptions, but their accuracy remains sensitive to the bandwidth characteristics of the stress power spectral density. Based on field‐test stress measurements, stationary Gaussian stress segments were extracted, and the corresponding time‐domain rainflow‐counting damage was calculated as the benchmark for evaluating frequency‐domain prediction accuracy. A practical 5RMS stress‐amplitude boundary was proposed as an engineering upper integration bound for fatigue‐damage calculation. A bandwidth‐corrected Dirlik method was further developed by introducing a bandwidth‐dependent correction coefficient into the original formulation. The resulting method retains the probabilistic structure and computational efficiency of the original Dirlik model, while improving bandwidth adaptability and reducing the maximum prediction error from approximately 50% to below 10%. Validation using representative train‐structure stress responses confirms the applicability of the proposed method to stationary Gaussian and PSD‐based fatigue assessment scenarios.
- 30 July 2025
- Published by Elsevier in Measurement
- Vol. 257
Assessment of stress identification for high-speed railway axle based on acceleration signals
- 30 July 2025
- Published by Elsevier in Measurement
- Vol. 257
Assessment of stress identification for high-speed railway axle based on acceleration signals
- 27 February 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (6) , 2495-2505
Evaluation of Small Fatigue Crack Growth Rates in HIP FGH96 Superalloy Under Microstructural Influences
The effects of different evaluation methods and microstructural characteristics on the surface small fatigue crack growth rate of HIP FGH96 superalloy were quantitatively investigated using SEM in situ and other testing technologies. The results indicate that the effect of projected length a1 and physical length a2 on the small fatigue crack growth rate can be ignored, even if there are some deflection angles in small crack growth path. However, clear distinctions emerge when evaluating the small fatigue crack growth rate near the crack growth threshold under mixed‐mode (Mode I/II) conditions, where the influence is quantitatively assessed using the maximum tangential stress criterion. Furthermore, differences between various evaluation methods of small fatigue crack growth rates and several important damage tolerance design parameters, such as ΔKth, aeq, or σw, were quantitatively predicted based on Weibull distribution analysis.
- 27 February 2025
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 48 (6) , 2495-2505
Evaluation of Small Fatigue Crack Growth Rates in HIP FGH96 Superalloy Under Microstructural Influences
The effects of different evaluation methods and microstructural characteristics on the surface small fatigue crack growth rate of HIP FGH96 superalloy were quantitatively investigated using SEM in situ and other testing technologies. The results indicate that the effect of projected length a1 and physical length a2 on the small fatigue crack growth rate can be ignored, even if there are some deflection angles in small crack growth path. However, clear distinctions emerge when evaluating the small fatigue crack growth rate near the crack growth threshold under mixed‐mode (Mode I/II) conditions, where the influence is quantitatively assessed using the maximum tangential stress criterion. Furthermore, differences between various evaluation methods of small fatigue crack growth rates and several important damage tolerance design parameters, such as ΔKth, aeq, or σw, were quantitatively predicted based on Weibull distribution analysis.
- 11 October 2024
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 134
Research on size effects in fracture properties and residual life prediction for high-speed train axles
- 11 October 2024
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 134
Research on size effects in fracture properties and residual life prediction for high-speed train axles
- 20 November 2023
- Published by Elsevier in Measurement
- Vol. 224
Study on the method of establishing the probability of detection curve for ultrasonic detection on railway hollow axle cracks
- 20 November 2023
- Published by Elsevier in Measurement
- Vol. 224
Study on the method of establishing the probability of detection curve for ultrasonic detection on railway hollow axle cracks
- 27 September 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (12) , 4649-4662
Research on monitoring method for crack depth of railway hollow axle during bench test
Hollow axles are critical safety components for high‐speed trains, and the operational safety of the axle is ensured by combining infinite life design and damage tolerance analysis based on ultrasonic testing. The establishment of the ultrasonic inspection interval requires the axle bench test, but it has been a challenge to obtain the initial crack at a determined depth. This paper proposes a method for predicting the transverse crack depth of axles by combining a full‐scale axle bench test with simulation analysis. The monitoring of crack depth is achieved by measuring the cracks on the axle surface. The crack propagation test was conducted to validate the prediction method with good results. The test results demonstrate the potential of crack monitoring methods in axle crack monitoring and provide new ideas for axle safety monitoring.
- 27 September 2023
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 46 (12) , 4649-4662
Research on monitoring method for crack depth of railway hollow axle during bench test
Hollow axles are critical safety components for high‐speed trains, and the operational safety of the axle is ensured by combining infinite life design and damage tolerance analysis based on ultrasonic testing. The establishment of the ultrasonic inspection interval requires the axle bench test, but it has been a challenge to obtain the initial crack at a determined depth. This paper proposes a method for predicting the transverse crack depth of axles by combining a full‐scale axle bench test with simulation analysis. The monitoring of crack depth is achieved by measuring the cracks on the axle surface. The crack propagation test was conducted to validate the prediction method with good results. The test results demonstrate the potential of crack monitoring methods in axle crack monitoring and provide new ideas for axle safety monitoring.
- 12 May 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (7) , 2072-2085
Influence of wheel out‐of‐roundness on the remaining life of railway wheels under mixed‐mode fatigue loading
As a common condition in train operation, the out‐of‐roundness (OOR) of wheels may have a great influence on the life of cracked wheels. In this study, the I–II mixed‐mode crack growth rate of different angles was tested, finite element analysis was carried out by using the test results, and the influence of different wheel roundness conditions on the life of cracked wheels was revealed. The results show that the mode II stress intensity factor of mixed‐mode cracks is the main driving force for crack propagation in the process of wheel rim crack growth. With an increase in the wheel scar length and the order of the wheel polygon, the crack propagation life decreases significantly.
- 12 May 2022
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 45 (7) , 2072-2085
Influence of wheel out‐of‐roundness on the remaining life of railway wheels under mixed‐mode fatigue loading
As a common condition in train operation, the out‐of‐roundness (OOR) of wheels may have a great influence on the life of cracked wheels. In this study, the I–II mixed‐mode crack growth rate of different angles was tested, finite element analysis was carried out by using the test results, and the influence of different wheel roundness conditions on the life of cracked wheels was revealed. The results show that the mode II stress intensity factor of mixed‐mode cracks is the main driving force for crack propagation in the process of wheel rim crack growth. With an increase in the wheel scar length and the order of the wheel polygon, the crack propagation life decreases significantly.