Limin Xu
Limin Xu has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Heng Wu
Guangdong University of Technology
3 shared publications Alhasan Fuseni
Saudi Aramco
2 shared publications- Hui Guo
Jiangxi Academy of Sciences
2 shared publications Lianglun Cheng
2 shared publications- Ming Han
Saudi Aramco
2 shared publications - Yuwen Qin
Guangdong University of Technology
2 shared publications
Latest Publications
- 8 August 2026
- Published by SAGE Publications in Journal of Composite Materials
A micro-CT-based “orientation–clustering–stiffness–damage” coupling framework for carbon-fiber/epoxy: From single-fiber scale to component-level failure prediction
A four-order “orientation-clustering-stiffness-damage” coupling framework is proposed for 28–30 vol% carbon-fiber/epoxy short-fiber composites (7 μm nominal fiber diameter, 3–5 mm chopped length), enabling accurate cross-scale failure prediction spanning from 60 μm single-fiber interfacial debonding regions up to 300 μm component-level representative volume elements that cover the full statistical distribution of fiber orientation and spatial arrangement. Twenty-one 30 × 30 × 30 mm 3 cubic specimens were in-situ imaged under quasi-static loading via synchrotron radiation Micro-CT at 0.5 μm voxel spacing, delivering approximately 1 μm effective spatial resolution after standard modulation transfer function deconvolution and ring-artifact suppression processing. The tomographic finite-element analysis workflow was fully synchronized to a pre-calibrated six-channel acoustic-emission array with 120 dB gain and 100 kHz–1 MHz bandwidth, where 15 specimens were exclusively used for multi-parameter model calibration through a genetic algorithm optimization loop, while the remaining six completely independent specimens were adopted for rigorous blind validation under uniaxial tension, biaxial compression and in-plane shear loading conditions. This framework achieves a tensile modulus prediction error below 5% and over 92% acoustic-emission hit event agreement on the fully unseen validation dataset, which significantly outperforms conventional Mori-Tanaka mean-field homogenization and periodic representative-volume-element homogenization methods by reducing prediction deviation by more than 40%. By embedding high-order orientation tensors, statistical fiber clustering spectral descriptors and gradient-sensitive non-local damage variables into a single physically interpretable constitutive kernel, the framework delivers an experimentally calibratable, highly scalable and transferable modeling paradigm, holding great practical application potential for composite process reverse design in aerospace and automotive lightweighting industries.
- 8 August 2026
- Published by SAGE Publications in Journal of Composite Materials
A micro-CT-based “orientation–clustering–stiffness–damage” coupling framework for carbon-fiber/epoxy: From single-fiber scale to component-level failure prediction
A four-order “orientation-clustering-stiffness-damage” coupling framework is proposed for 28–30 vol% carbon-fiber/epoxy short-fiber composites (7 μm nominal fiber diameter, 3–5 mm chopped length), enabling accurate cross-scale failure prediction spanning from 60 μm single-fiber interfacial debonding regions up to 300 μm component-level representative volume elements that cover the full statistical distribution of fiber orientation and spatial arrangement. Twenty-one 30 × 30 × 30 mm 3 cubic specimens were in-situ imaged under quasi-static loading via synchrotron radiation Micro-CT at 0.5 μm voxel spacing, delivering approximately 1 μm effective spatial resolution after standard modulation transfer function deconvolution and ring-artifact suppression processing. The tomographic finite-element analysis workflow was fully synchronized to a pre-calibrated six-channel acoustic-emission array with 120 dB gain and 100 kHz–1 MHz bandwidth, where 15 specimens were exclusively used for multi-parameter model calibration through a genetic algorithm optimization loop, while the remaining six completely independent specimens were adopted for rigorous blind validation under uniaxial tension, biaxial compression and in-plane shear loading conditions. This framework achieves a tensile modulus prediction error below 5% and over 92% acoustic-emission hit event agreement on the fully unseen validation dataset, which significantly outperforms conventional Mori-Tanaka mean-field homogenization and periodic representative-volume-element homogenization methods by reducing prediction deviation by more than 40%. By embedding high-order orientation tensors, statistical fiber clustering spectral descriptors and gradient-sensitive non-local damage variables into a single physically interpretable constitutive kernel, the framework delivers an experimentally calibratable, highly scalable and transferable modeling paradigm, holding great practical application potential for composite process reverse design in aerospace and automotive lightweighting industries.
- 18 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (6) , 11076
FACTNet: a frequency-domain-informed transformer for mmWave image computational super-resolution in the spatial frequency domain
Millimeter-wave (mmWave) imaging is a vital security screening technology, prized for its non-ionizing and penetrative capabilities. However, its efficacy is fundamentally limited by the physical principle of diffraction, which acts as a low-pass filter, irreversibly attenuating the high-frequency spatial details essential for identifying concealed objects. Prevailing deep learning-based computational super-resolution methods, operating predominantly in the spatial domain, struggle to counteract this frequency-specific information loss and thus often fail to restore fine textures and sharp edges. Inspired by this physical insight, we propose the frequency-aware cross-attention transformer network (FACTNet), an architecture designed to directly confront this challenge in the frequency domain. Its core innovation, the frequency-domain transformation module (FDTM), empowers the network to learn an adaptive filter in the Fourier domain, explicitly amplifying the high-frequency spectral components suppressed during image acquisition. Evaluations on our custom mmWave security dataset demonstrate that FACTNet achieves state-of-the-art performance, yielding reconstructions with superior visual fidelity, enhanced detail, and fewer artifacts. Our work establishes that aligning a network’s computational domain with the physical nature of image degradation provides a more effective and principled pathway to solving computational super-resolution reconstruction problems.
- 18 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (6) , 11076
FACTNet: a frequency-domain-informed transformer for mmWave image computational super-resolution in the spatial frequency domain
Millimeter-wave (mmWave) imaging is a vital security screening technology, prized for its non-ionizing and penetrative capabilities. However, its efficacy is fundamentally limited by the physical principle of diffraction, which acts as a low-pass filter, irreversibly attenuating the high-frequency spatial details essential for identifying concealed objects. Prevailing deep learning-based computational super-resolution methods, operating predominantly in the spatial domain, struggle to counteract this frequency-specific information loss and thus often fail to restore fine textures and sharp edges. Inspired by this physical insight, we propose the frequency-aware cross-attention transformer network (FACTNet), an architecture designed to directly confront this challenge in the frequency domain. Its core innovation, the frequency-domain transformation module (FDTM), empowers the network to learn an adaptive filter in the Fourier domain, explicitly amplifying the high-frequency spectral components suppressed during image acquisition. Evaluations on our custom mmWave security dataset demonstrate that FACTNet achieves state-of-the-art performance, yielding reconstructions with superior visual fidelity, enhanced detail, and fewer artifacts. Our work establishes that aligning a network’s computational domain with the physical nature of image degradation provides a more effective and principled pathway to solving computational super-resolution reconstruction problems.
- 3 April 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (7) , 16237-16252
Multi-scale super-resolution reconstruction of terahertz images for postal security inspection
Millimeter-wave and terahertz imaging systems have been used for security checks of human bodies, small postal packages, and industrial nondestructive evaluation. The image resolution is one of the key factors affecting the accuracy of contraband detection and inner defect analysis. We propose a super-resolution reconstruction algorithm based on multi-scale channel attention (MS-CA) residual network to enhance the terahertz images, which are acquired through a homemade real-time terahertz imaging system for postal security inspection. The generalized residual block was introduced and transformed as the basic feature extraction unit, and the channel attention descriptor was inserted in the pooling layer to achieve the channel attention training for the 2D feature map. The fractional matching relationship of pixel coordinates between the HR image and the LR image in the upscale module can achieve reconstruction at any continuous scale. Comparison with traditional deep-learning based algorithms shows that our algorithm outperforms with the highest peak power signal-to-noise ratio (PSNR) and structural similarity index (SSIM) while reconstructing terahertz images at any scale factor.
- 3 April 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (7) , 16237-16252
Multi-scale super-resolution reconstruction of terahertz images for postal security inspection
Millimeter-wave and terahertz imaging systems have been used for security checks of human bodies, small postal packages, and industrial nondestructive evaluation. The image resolution is one of the key factors affecting the accuracy of contraband detection and inner defect analysis. We propose a super-resolution reconstruction algorithm based on multi-scale channel attention (MS-CA) residual network to enhance the terahertz images, which are acquired through a homemade real-time terahertz imaging system for postal security inspection. The generalized residual block was introduced and transformed as the basic feature extraction unit, and the channel attention descriptor was inserted in the pooling layer to achieve the channel attention training for the 2D feature map. The fractional matching relationship of pixel coordinates between the HR image and the LR image in the upscale module can achieve reconstruction at any continuous scale. Comparison with traditional deep-learning based algorithms shows that our algorithm outperforms with the highest peak power signal-to-noise ratio (PSNR) and structural similarity index (SSIM) while reconstructing terahertz images at any scale factor.
- 12 June 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (18) , 4868-4873
Contraband detection of millimeter wave image for postal security checks using a spatial transformer-feature fusion network
The image resolution and contraband object detection accuracy are the two key factors for security checks based on millimeter wave imaging techniques. In this paper, a homemade real-time millimeter imaging system for small package security inspection is used to obtain about 400 raw images of envelopes containing multi-contraband objects like guns and knives. After pre-processing, spatial transformer-feature fusion (ST-FF) adapted single-shot multi-box detector (SSD) networks are used to detect the contraband objects of postal packages. The experiments reveal that the spatial-transformed-feature fusion deep learning networks demonstrate better mean average precision (mAP) performance than traditional single networks in detecting contraband objects of different scales, orientations, and distortions, and prove the great potential for security checks based on millimeter wave imaging.
- 12 June 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (18) , 4868-4873
Contraband detection of millimeter wave image for postal security checks using a spatial transformer-feature fusion network
The image resolution and contraband object detection accuracy are the two key factors for security checks based on millimeter wave imaging techniques. In this paper, a homemade real-time millimeter imaging system for small package security inspection is used to obtain about 400 raw images of envelopes containing multi-contraband objects like guns and knives. After pre-processing, spatial transformer-feature fusion (ST-FF) adapted single-shot multi-box detector (SSD) networks are used to detect the contraband objects of postal packages. The experiments reveal that the spatial-transformed-feature fusion deep learning networks demonstrate better mean average precision (mAP) performance than traditional single networks in detecting contraband objects of different scales, orientations, and distortions, and prove the great potential for security checks based on millimeter wave imaging.
- Open Access
- 10 May 2024
- Published by MDPI AG in Biosensors
- Vol. 14 (5) , 240
Highly Sensitive Qualitative and Quantitative Identification of Cashmere and Wool Based on Terahertz Electromagnetically Induced Transparent Metasurface Biosensor
Cashmere and wool are both natural animal fibers used in the textile industry, but cashmere is of superior quality, is rarer, and more precious. It is therefore important to distinguish the two fibers accurately and effectively. However, challenges due to their similar appearance, morphology, and physical and chemical properties remain. Herein, a terahertz electromagnetic inductive transparency (EIT) metasurface biosensor is introduced for qualitative and quantitative identification of cashmere and wool. The periodic unit structure of the metasurface consists of four rotationally symmetric resonators and two cross−arranged metal secants to form toroidal dipoles and electric dipoles, respectively, so that its effective sensing area can be greatly improved by 1075% compared to the traditional dipole mode, and the sensitivity will be up to 342 GHz/RIU. The amplitude and frequency shift changes of the terahertz transmission spectra caused by the different refractive indices of cashmere/wool can achieve highly sensitive label−free qualitative and quantitative identification of both. The experimental results show that the terahertz metasurface biosensor can work at a concentration of 0.02 mg/mL. It provides a new way to achieve high sensitivity, precision, and trace detection of cashmere/wool, and would be a valuable application for the cashmere industry.
- 10 May 2024
- Published by MDPI AG in Biosensors
- Vol. 14 (5) , 240
Open AccessHighly Sensitive Qualitative and Quantitative Identification of Cashmere and Wool Based on Terahertz Electromagnetically Induced Transparent Metasurface Biosensor
Cashmere and wool are both natural animal fibers used in the textile industry, but cashmere is of superior quality, is rarer, and more precious. It is therefore important to distinguish the two fibers accurately and effectively. However, challenges due to their similar appearance, morphology, and physical and chemical properties remain. Herein, a terahertz electromagnetic inductive transparency (EIT) metasurface biosensor is introduced for qualitative and quantitative identification of cashmere and wool. The periodic unit structure of the metasurface consists of four rotationally symmetric resonators and two cross−arranged metal secants to form toroidal dipoles and electric dipoles, respectively, so that its effective sensing area can be greatly improved by 1075% compared to the traditional dipole mode, and the sensitivity will be up to 342 GHz/RIU. The amplitude and frequency shift changes of the terahertz transmission spectra caused by the different refractive indices of cashmere/wool can achieve highly sensitive label−free qualitative and quantitative identification of both. The experimental results show that the terahertz metasurface biosensor can work at a concentration of 0.02 mg/mL. It provides a new way to achieve high sensitivity, precision, and trace detection of cashmere/wool, and would be a valuable application for the cashmere industry.
- 24 November 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 177, 107929
Mixed modes crack propagation of orthogonal woven-layer in carbon/aramid/epoxy laminates
- 24 November 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 177, 107929
Mixed modes crack propagation of orthogonal woven-layer in carbon/aramid/epoxy laminates
- Open Access
Efficient Frozen Gaussian Sampling Algorithms for Nonadiabatic Quantum Dynamics at Metal Surfaces
In this article, we propose a Frozen Gaussian Sampling (FGS) algorithm for simulating nonadiabatic quantum dynamics at metal surfaces with a continuous spectrum. This method consists of a Monte-Carlo algorithm for sampling the initial wave packets on the phase space and a surface-hopping type stochastic time propagation scheme for the wave packets. We prove that to reach a certain accuracy threshold, the sample size required is independent of both the semiclassical parameter $\varepsilon$ and the number of metal orbitals $N$, which makes it one of the most promising methods to study the nonadiabatic dynamics. The algorithm and its convergence properties are also validated numerically. Furthermore, we carry out numerical experiments including exploring the nuclei dynamics, electron transfer and finite-temperature effects, and demonstrate that our method captures the physics which can not be captured by classical surface hopping trajectories.Open AccessEfficient Frozen Gaussian Sampling Algorithms for Nonadiabatic Quantum Dynamics at Metal Surfaces
In this article, we propose a Frozen Gaussian Sampling (FGS) algorithm for simulating nonadiabatic quantum dynamics at metal surfaces with a continuous spectrum. This method consists of a Monte-Carlo algorithm for sampling the initial wave packets on the phase space and a surface-hopping type stochastic time propagation scheme for the wave packets. We prove that to reach a certain accuracy threshold, the sample size required is independent of both the semiclassical parameter $\varepsilon$ and the number of metal orbitals $N$, which makes it one of the most promising methods to study the nonadiabatic dynamics. The algorithm and its convergence properties are also validated numerically. Furthermore, we carry out numerical experiments including exploring the nuclei dynamics, electron transfer and finite-temperature effects, and demonstrate that our method captures the physics which can not be captured by classical surface hopping trajectories. - 19 May 2022
- Published by Optica Publishing Group in Applied Optics
- Vol. 61 (15) , 4567-4570
Quantifying the shape effect of plasmonic gold nanoparticles on photoacoustic conversion efficiency
Gold nanoparticles with strong localized plasmonic effects have found wide applications in photoacoustic imaging, which are ascribed to their unique microscopic mechanism of converting photons to ultrasound. In this report, we quantitatively model the time-resolved temperature field, thermal expansion, and pressure distribution based on the finite element analysis method, and two-dimensional gold nanoparticles spanning from the triangle, square, pentagon, and hexagon to the circle have been systematically studied. Results show that the shape of gold nanoparticles has a nontrivial effect on photoacoustic conversion efficiency, and the square-shaped gold structure exhibits the best performance. Our findings could shed light on the shape design of high-performance photoacoustic agents in the future.
- 19 May 2022
- Published by Optica Publishing Group in Applied Optics
- Vol. 61 (15) , 4567-4570
Quantifying the shape effect of plasmonic gold nanoparticles on photoacoustic conversion efficiency
Gold nanoparticles with strong localized plasmonic effects have found wide applications in photoacoustic imaging, which are ascribed to their unique microscopic mechanism of converting photons to ultrasound. In this report, we quantitatively model the time-resolved temperature field, thermal expansion, and pressure distribution based on the finite element analysis method, and two-dimensional gold nanoparticles spanning from the triangle, square, pentagon, and hexagon to the circle have been systematically studied. Results show that the shape of gold nanoparticles has a nontrivial effect on photoacoustic conversion efficiency, and the square-shaped gold structure exhibits the best performance. Our findings could shed light on the shape design of high-performance photoacoustic agents in the future.
- 21 March 2022
- Published by Society of Petroleum Engineers (SPE)
New Synergistic Surfactant Mixtures for Improving Oil Production in Carbonate Reservoirs
The paper presents the development of new surfactant formulations composed of various low-cost and low-performance surfactants to make them high performance products for high temperature and high salinity carbonate reservoirs. The objective of this study is to optimize the surfactant chemistry by mixing different kinds of surfactants (ionic, nonionic, and amphoteric), which results in significant synergistic effects in interfacial properties to improve oil production at the given harsh conditions. The optimal mixing surfactant ratios were determined according to the brine-surfactant compatibility, microemulsion phase behavior, and the interfacial tension (IFT) between oil and surfactant solutions in high salinity brine and at 90˚C. Comprehensive performance of the surfactants was evaluated, including adsorption of the surfactants onto the carbonate rocks and the long-term stability at 95˚C. The coreflooding displacement experiments were performed using carbonate core plugs at 95˚C to evaluate the potential of the optimal mixing surfactants in improving oil production. Three formulations composed of two types of low-cost surfactants were developed in this study. The mixing surfactants were chosen based on moderate electrostatic interaction among the surfactants. It appeared the synergistic effect between the mixing surfactants was enhanced with increasing temperature. Although the IFT of the individual surfactants with crude oil was in the range of 100mN/m, a significant IFT reduction in the magnitude of 10−2 - 10−3 mN/m was observed by mixing the surfactants. A salinity scan showed that the IFT values maintained a value of 10−2 mN/m in a wide salinity range, which demonstrated the robustness of the surfactants mixtures. In microemulsion phase behavior studies, these mixed surfactant solutions in the presence of crude oil exhibited Winsor Type III emulsions. The static adsorptions of the mixed surfactants were lower than the individual surfactant adsorption. All this indicated the feasibility of these formulations for their applications in the harsh reservoir conditions. The results of coreflooding displacement tests demonstrated significant oil production improvement beyond water flooding. This work provides an efficient way to get surfactant formulations by mixing low-performance and low cost surfactants to obtain high performance in improving oil production under the harsh conditions.
- 21 March 2022
- Published by Society of Petroleum Engineers (SPE)
New Synergistic Surfactant Mixtures for Improving Oil Production in Carbonate Reservoirs
The paper presents the development of new surfactant formulations composed of various low-cost and low-performance surfactants to make them high performance products for high temperature and high salinity carbonate reservoirs. The objective of this study is to optimize the surfactant chemistry by mixing different kinds of surfactants (ionic, nonionic, and amphoteric), which results in significant synergistic effects in interfacial properties to improve oil production at the given harsh conditions. The optimal mixing surfactant ratios were determined according to the brine-surfactant compatibility, microemulsion phase behavior, and the interfacial tension (IFT) between oil and surfactant solutions in high salinity brine and at 90˚C. Comprehensive performance of the surfactants was evaluated, including adsorption of the surfactants onto the carbonate rocks and the long-term stability at 95˚C. The coreflooding displacement experiments were performed using carbonate core plugs at 95˚C to evaluate the potential of the optimal mixing surfactants in improving oil production. Three formulations composed of two types of low-cost surfactants were developed in this study. The mixing surfactants were chosen based on moderate electrostatic interaction among the surfactants. It appeared the synergistic effect between the mixing surfactants was enhanced with increasing temperature. Although the IFT of the individual surfactants with crude oil was in the range of 100mN/m, a significant IFT reduction in the magnitude of 10−2 - 10−3 mN/m was observed by mixing the surfactants. A salinity scan showed that the IFT values maintained a value of 10−2 mN/m in a wide salinity range, which demonstrated the robustness of the surfactants mixtures. In microemulsion phase behavior studies, these mixed surfactant solutions in the presence of crude oil exhibited Winsor Type III emulsions. The static adsorptions of the mixed surfactants were lower than the individual surfactant adsorption. All this indicated the feasibility of these formulations for their applications in the harsh reservoir conditions. The results of coreflooding displacement tests demonstrated significant oil production improvement beyond water flooding. This work provides an efficient way to get surfactant formulations by mixing low-performance and low cost surfactants to obtain high performance in improving oil production under the harsh conditions.
- 13 October 2019
- Published by Society of Petroleum Engineers (SPE)
Study on Oppositely Charged Polymer and Surfactant Mixture for Enhancing Oil Production
Polymer-surfactant mixtures in aqueous solutions present unique rheological and interfacial properties that promote their applications in chemical flooding. The objective of this study is to investigate the interaction between anionic polyacrylamides and cationic surfactants in different temperature and salinity conditions and the potential application of the polymer-surfactant mixtures in carbonate reservoirs. Cationic surfactants were selected owing to low adsorption on carbonate rocks. Compatibility tests of polymer-surfactant mixtures were conducted in brine with different salinities to study the interaction between anionic polymers and cationic surfactants in the presence of salts. The effect of cationic surfactants on polymer viscosity at different temperatures was investigated. The compatibility of the mixtures of the cationic surfactants and the anionic polymers was significantly improved in high salinity injection water (with a total dissolved solid of 57,670 mg/L), compared with the compatibility in deionized water. This is attributed to the shielding of polymer and surfactant charges by the salts, which diminishes the electrostatic interaction between the chemicals. Rheological measurements indicated that the polymer viscosity increased in the presence of the cationic surfactant CAS-S or CAS-B. This effect was decreased at 90˚C. Other cationic surfactant CAS-1 or CAS-3 slightly increased the polymer viscosity at 25˚C and significantly decreased the viscosity at 90˚C. These observations can be explained based on the surfactants self-assembly. At room temperature, CAS-1 and CAS-3 form spherical micelles while CAS-S and CAS-B form wormlike micelles. The entanglement of the polymers with wormlike micelles explains the observed viscosity enhancement. At 90˚C, wormlike micelles became shorter which weakens this viscosity enhancement effect. In conclusion, the charges and self-assembly structures of surfactants play an important role in the performance of polymer-surfactant mixtures that should be taken into account in the design of optimal formulations. This work provides the insight of interaction between anionic polymers and cationic surfactants with different self-assembly structures for the potential application in improving oil production.
- 13 October 2019
- Published by Society of Petroleum Engineers (SPE)
Study on Oppositely Charged Polymer and Surfactant Mixture for Enhancing Oil Production
Polymer-surfactant mixtures in aqueous solutions present unique rheological and interfacial properties that promote their applications in chemical flooding. The objective of this study is to investigate the interaction between anionic polyacrylamides and cationic surfactants in different temperature and salinity conditions and the potential application of the polymer-surfactant mixtures in carbonate reservoirs. Cationic surfactants were selected owing to low adsorption on carbonate rocks. Compatibility tests of polymer-surfactant mixtures were conducted in brine with different salinities to study the interaction between anionic polymers and cationic surfactants in the presence of salts. The effect of cationic surfactants on polymer viscosity at different temperatures was investigated. The compatibility of the mixtures of the cationic surfactants and the anionic polymers was significantly improved in high salinity injection water (with a total dissolved solid of 57,670 mg/L), compared with the compatibility in deionized water. This is attributed to the shielding of polymer and surfactant charges by the salts, which diminishes the electrostatic interaction between the chemicals. Rheological measurements indicated that the polymer viscosity increased in the presence of the cationic surfactant CAS-S or CAS-B. This effect was decreased at 90˚C. Other cationic surfactant CAS-1 or CAS-3 slightly increased the polymer viscosity at 25˚C and significantly decreased the viscosity at 90˚C. These observations can be explained based on the surfactants self-assembly. At room temperature, CAS-1 and CAS-3 form spherical micelles while CAS-S and CAS-B form wormlike micelles. The entanglement of the polymers with wormlike micelles explains the observed viscosity enhancement. At 90˚C, wormlike micelles became shorter which weakens this viscosity enhancement effect. In conclusion, the charges and self-assembly structures of surfactants play an important role in the performance of polymer-surfactant mixtures that should be taken into account in the design of optimal formulations. This work provides the insight of interaction between anionic polymers and cationic surfactants with different self-assembly structures for the potential application in improving oil production.