Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Helder Nunes has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of AlTiB Grain Refinement and AlSr Modification in Fe-Contaminated Secondary AlSi7Mg0.3 Alloys

    by Helder Nunes, Manuel F. Vieira, Ana Reis, Omid Emadinia

    Fe contamination is a major limitation in the upcycling of secondary Al-Si casting alloys. Inevitable Fe contamination during recycling processes, such as automotive shredding, promotes the formation of brittle Fe-rich intermetallic compounds that severely compromise ductility. In this work, the effectiveness and limitations of conventional industrial melt treatments AlTi5B1 grain refinement and AlSr5 modification were systematically evaluated. The synergistic effects of these additions on the microstructure evolution and mechanical properties of AlSi7Mg0.3 alloys with increasing Fe contents (0.1, 1.3 and 3.8 wt.%) were assessed. A Taguchi experimental design was applied to assess each individual treatment and combined influence on the size, morphology, and distribution of Fe-rich intermetallic phases. Quantitative image analysis, supported by ANOVA, revealed that optimized additions (3 wt.% AlTi5B1 and 0.5 wt.% AlSr5) effectively reduce the size of Fe-rich intermetallics and promote the formation of less detrimental α-AlFeSi phases at high Fe levels. However, these microstructural modifications were insufficient to prevent severe embrittlement. Tensile properties, particularly ductility, remained low, and fracture behavior was dominated by the high-volume fraction of brittle intermetallic phases. The results demonstrate that while conventional grain refinement and modification treatments can partially mitigate Fe-related degradation, they are insufficient for the upcycling of highly Fe-contaminated secondary aluminum alloys within a circular economy framework. Graphical Abstract

  • Open Access

    Optimising WC-25Co Feedstock and Parameters for Laser-Directed Energy Deposition

    by Helder Nunes, José Nhanga, Luís Regueiras, Ana Reis, Manuel F. Vieira, Bruno Guimarães, Daniel Figueiredo, Cristina Fernandes, Omid Emadinia

    Laser-Directed Energy Deposition (L-DED) is an additive manufacturing technique used for producing and repairing components, mainly for coating applications, depositing metal matrix composites such as cemented carbides, composed of hard metal carbides and a metallic binder. In this sense, this study evaluated the preparation of a ready-to-press WC-25Co powder as a reliable feedstock for L-DED process. This powder required pre-heat treatment studies to prevent fragmentation during powder feeding, due to the absence of metallurgical bonding between WC and Co particles. In the current study, the Taguchi methodology was used, varying laser power, powder feed rate, and scanning speed to reach an optimised deposition window. The best bead morphology resulted from 2400 W laser power, 11 mm/s scanning speed, and 9 g/min feed rate. Moreover, defects such as porosity and cracking were mitigated by applying a remelting strategy of 2400 W and 9 mm/s. Therefore, a perfect deposition is obtained using the optimised processing parameters. Microstructural analysis of the optimised deposited line revealed a fine structure, comprising columnar and equiaxed dendrites of complex carbides. The average hardness of the deposited WC-25Co powder on a AISI 1045 steel was 854 ± 37 HV0.2. These results demonstrate the potential of L-DED for processing high-performance cemented carbide coatings.

  • Open Access

    Excessive Fe Contamination in Secondary Al Alloys: Microstructure, Porosity, and Corrosion Behaviour

    by Helder Nunes, Rui Madureira, Manuel F. Vieira, Ana Reis, Omid Emadinia

    The characterisation of aluminium casting alloys with iron concentrations exceeding current standards is essential, as upcycling has recently become a significant concern in achieving a more circular economy. Secondary aluminium casting alloys often exhibit insufficient mechanical properties for load-bearing automotive applications due to contamination with iron, mainly due to alloy mixing or remnants from end-of-life products during downcycling. This trend is anticipated to soon lead to a surplus of scrap. This study aims to fully understand the microstructural changes, intermetallic phase morphologies, and defect formation in AlSiMg alloy highly contaminated with Fe that exists in Al scraps and is detrimental for upcycling purposes. The investigation examined the AlSi7Mg0.3 alloy with Fe concentrations ranging from 0.1 to 3.8 wt.% Fe, employing thermodynamic simulations, hardness testing, quantitative image analysis, and corrosion tests. Among these alloys, the AlSi7Mg0.3-3.8Fe, containing the highest level of contamination, exhibited the most complex microstructure. This microstructure is characterised by the presence of two distinct Fe-rich intermetallic phases with diverse shapes and sizes: petal-like α′-Al8Fe2Si, long and thick β-Al4.5FeSi plaques, and very thin β-Al4.5FeSi needles. The significant growth in these phases with higher Fe concentration resulted in increases in hardness (15 HBW), porosity (1.39%), and corrosion rate (approximately 12 times).


  • Open Access

    Adding Value to Secondary Aluminum Casting Alloys: A Review on Trends and Achievements

    by Helder Nunes, Omid Emadinia, Rui Soares, Manuel F. Vieira, Ana Reis

    Aluminum is a critical element of the circular economy as it can be recycled several times. Moreover, Al recycling is a more economically and environmentally efficient procedure than the primary Al production from ores. Secondary aluminum alloys are mostly used in casting applications since it is possible to accommodate their chemical composition through secondary manufacturing processes. However, the quality of the alloys may be considerably altered during the different steps of the recycling process. Inadequate waste sorting might result in excessive contamination. Iron is the most dangerous contaminant because it causes brittle and fragile intermetallic phases, which significantly impacts the mechanical characteristics of alloys. In addition, the microstructure of the alloy changes significantly after multiple cycles of remelting. These issues lead to the downcycling of aluminum, i.e., in other words, the reduction in the overall quality of the alloys. Thus, it has been shown that a number of procedures, including ultrasonic melt treatment and microalloying with rare earths, can somewhat alter the shape of the Fe-rich phases in order to reduce the shortcomings of downcycling. However, a solid mechanical characterization is still missing in order to improve the Fe-rich phase alteration.


  • Infiltration of aluminum in 3D‐printed metallic inserts

    by Helder Nunes, Omid Emadinia, José Costa, Rui Madureira, Rui Soares, José Silva, Inês Frada, Vitor Anjos, Filomena Viana, Manuel Vieira, et al.

    Aluminum structural composites through the infiltration process can be performed by vacuum, centrifugal, or squeeze casting, involving the infiltration of molten Al into fibers, particles, foams, or even porous preforms. This methodology creates hybrid structures of two distinct metal alloys that can be used to locally strengthen components or even to improve the properties of bulk materials, such as ultimate tensile strength and thermal conductivity. New approaches involve the infiltration of liquid Al into a three‐dimensional (3D)‐printed structure of the more rigid metal, such as steel, that the Al matrix. In the current study, stainless steel and copper inserts were produced by fused filament fabrication techniques with various geometries. Moreover, some 3D inserts were electrochemically coated with pure copper to enhance the wettability of the steel insert by Al. Then, the infiltration of these inserts was evaluated by gravity casting, centrifugal casting, and low‐pressure sand casting (LPSC). Evaluations involved microstructural characterization using optical microscopy and SEM for interface analysis. It is revealed that centrifugal casting is highly reliable to infiltrate the inserts with Al, filling detailed cavities in depth. The copper coating aided in the creation of intimate interfaces. The infiltration at the insert's surfaces, curved‐like topography, is obtained through LPSC though it is affected by the direction in respect of material flow.


  • Open Access

    Additively Manufactured Ti-6Al-4V: Effects of Heat-Treatment

    by Helder Nunes, José M. Costa, Filomena Viana, Manuel F. Vieira

    Due to its superior specific strength, corrosion resistance, and biocompatibility, Ti-6Al-4V alloy is the most frequently used titanium alloy, with a wide range of applications in numerous industries


  • Open Access

    Sedimentation in the A356-Al2O3 Stirred Cast

    by Omid Emadinia, Rui Madureira, Rui Soares, Helder Nunes, Inês Frada, Vitor Anjos, Carlos Silva Ribeiro, Rui Neto, Ana Reis, Manuel Vieira

    The production of aluminium metal matrix composites (AlMMCs) is noteworthy for obtaining enhanced mechanical and/or physical properties such as a high strength-to-weight ratio, high stiffness, high wear resistance, and higher thermal conductivity or modified coefficient of thermal expansion