Jiří Čapek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiří Čapek has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Petr Zeman
University of West Bohemia
9 shared publications - Radomir Cerstvy
University of West Bohemia
7 shared publications - Tomáš Kozák
University of West Bohemia in Pilsen
7 shared publications - Stanislav Haviar
Department of Physics and NTIS—European Centre of Excellence, University of West Bohemia in Pilsen 2 , Univerzitní 8, Pilsen 301 00
6 shared publications - Kalyani Shaji5 shared publications
- Nirmal Kumar
Department of Physics and NTIS-European Centre of Excellence, University of West Bohemia, Univerzitni 8, 301 00 Pilsen, Czech Republic
5 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (11) , 115013
Deposition rate and energy to substrate in chopped and standard HiPIMS: identifying optimal pulse parameters
High-power impulse magnetron sputtering (HiPIMS) delivers higher ionisation of the target material at the expense of lower deposition rates than conventional magnetron sputtering. A fine optimisation of the deposition conditions is crucial for specific applications. Chopped or multi-pulse HiPIMS (segmenting pulses into shorter micropulses) has been proposed to enhance the degree of ionisation of the film-forming flux fraction while maintaining the deposition rate. This study investigates how micropulse length and the delay time between segments influence energy flux, deposition rate, and the ionised flux fraction (IFF) in both chopped and standard HiPIMS (s-HiPIMS). These quantities are evaluated by passive thermal probe, biasable QCM and mass spectrometer measurements at the substrate position. Deposition-averaged and pulse-averaged power is kept constant for all conditions to facilitate meaningful comparison. Results indicate that chopping the HiPIMS pulse consistently leads to higher energy flux and total deposition rate compared to s-HiPIMS at the same total pulse length, primarily due to increased ion flux. In chopped HiPIMS, increasing the delay time between micropulses beyond 30 μ s simultaneously improved the deposition rate and the IFF. In comparison, s-HiPIMS, operated at higher frequencies and shorter pulse lengths, demonstrated similar performance with even higher total energy fluxes, but this can be attributed to a higher fraction of process-gas ions in the flux to the substrate, rather than to an increased IFF of the film-forming species.
- 1 November 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (11) , 115013
Open AccessDeposition rate and energy to substrate in chopped and standard HiPIMS: identifying optimal pulse parameters
High-power impulse magnetron sputtering (HiPIMS) delivers higher ionisation of the target material at the expense of lower deposition rates than conventional magnetron sputtering. A fine optimisation of the deposition conditions is crucial for specific applications. Chopped or multi-pulse HiPIMS (segmenting pulses into shorter micropulses) has been proposed to enhance the degree of ionisation of the film-forming flux fraction while maintaining the deposition rate. This study investigates how micropulse length and the delay time between segments influence energy flux, deposition rate, and the ionised flux fraction (IFF) in both chopped and standard HiPIMS (s-HiPIMS). These quantities are evaluated by passive thermal probe, biasable QCM and mass spectrometer measurements at the substrate position. Deposition-averaged and pulse-averaged power is kept constant for all conditions to facilitate meaningful comparison. Results indicate that chopping the HiPIMS pulse consistently leads to higher energy flux and total deposition rate compared to s-HiPIMS at the same total pulse length, primarily due to increased ion flux. In chopped HiPIMS, increasing the delay time between micropulses beyond 30 μ s simultaneously improved the deposition rate and the IFF. In comparison, s-HiPIMS, operated at higher frequencies and shorter pulse lengths, demonstrated similar performance with even higher total energy fluxes, but this can be attributed to a higher fraction of process-gas ions in the flux to the substrate, rather than to an increased IFF of the film-forming species.
- Open Access
- 23 May 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 305
Highly photoactive Cu2O films with enhanced crystallinity for PEC water splitting
- 23 May 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 305
Open AccessHighly photoactive Cu2O films with enhanced crystallinity for PEC water splitting
- Open Access
- 28 February 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 221
Corrosion-resistant and conductive Ti–Nb–O coatings tailored for ultra-low Pt-loaded BPPs and PTLs in PEM electrolyzers
- 28 February 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 221
Open AccessCorrosion-resistant and conductive Ti–Nb–O coatings tailored for ultra-low Pt-loaded BPPs and PTLs in PEM electrolyzers
- Open Access
- 14 February 2026
- Published by Elsevier in SSRN Electronic Journal
Highly photoactive Cu2O films with enhanced crystallinity for PEC water splitting
This study explores the deposition of single-phase Cu2O films using magnetron sputtering techniques, with a focus on comparing Direct Current Magnetron Sputtering (DCMS) and High-Power Impulse Magnetron Sputtering (HiPIMS). The HiPIMS technique demonstrated several advantages over DCMS, including more straightforward deposition, improved crystallinity, and higher photocurrent density, jph, during linear sweep voltammetry measurements. As a result, films prepared by HiPIMS became the focus of further optimization. The effects of key deposition parameters – such as substrate temperature, oxygen partial pressure, film thickness, and post-deposition annealing – on the structural and photoelectrochemical properties of Cu2O films were systematically investigated. The optimized films exhibited a fully densified microstructure, high crystallinity, and enhanced jph values. The highest jph of −3 mA/cm2 at 0.03 V vs. RHE was achieved for a 5-µm thick film deposited at an oxygen partial pressure of 0.42 Pa and a substrate temperature of 500 °C, followed by post-annealing at 600 °C in a vacuum. This represents the highest jph value reported to date for a bare Cu2O photocathodes. These results highlight the potential of HiPIMS-deposited Cu2O films for efficient photoelectrochemical water splitting.
- 14 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessHighly photoactive Cu2O films with enhanced crystallinity for PEC water splitting
This study explores the deposition of single-phase Cu2O films using magnetron sputtering techniques, with a focus on comparing Direct Current Magnetron Sputtering (DCMS) and High-Power Impulse Magnetron Sputtering (HiPIMS). The HiPIMS technique demonstrated several advantages over DCMS, including more straightforward deposition, improved crystallinity, and higher photocurrent density, jph, during linear sweep voltammetry measurements. As a result, films prepared by HiPIMS became the focus of further optimization. The effects of key deposition parameters – such as substrate temperature, oxygen partial pressure, film thickness, and post-deposition annealing – on the structural and photoelectrochemical properties of Cu2O films were systematically investigated. The optimized films exhibited a fully densified microstructure, high crystallinity, and enhanced jph values. The highest jph of −3 mA/cm2 at 0.03 V vs. RHE was achieved for a 5-µm thick film deposited at an oxygen partial pressure of 0.42 Pa and a substrate temperature of 500 °C, followed by post-annealing at 600 °C in a vacuum. This represents the highest jph value reported to date for a bare Cu2O photocathodes. These results highlight the potential of HiPIMS-deposited Cu2O films for efficient photoelectrochemical water splitting.
- Open Access
- 6 November 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 30
WO3/CuWO4 nanocomposite thin films for humidity resilient acetone gas sensing
- 6 November 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 30
Open AccessWO3/CuWO4 nanocomposite thin films for humidity resilient acetone gas sensing
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (59) , 2782
Tailoring Microstructure and Composition of Composite CuO/WO3 Nanoparticle-Based Thin Films for Enhanced H2 Gas Sensing
The conductometric gas sensors operate by modulating the electrical conductivity of the sensing material through adsorption-desorption reactions between the target gas and the sensor surface. Metal oxide semiconductors (MOS) are conductometric materials highly sensitive to oxidizing and reducing gases. In addition, composite MOS-based materials may further benefit from formed heterojunctions potentially significantly improving the sensitivity. Our focus is to develop advanced hydrogen-gas sensing materials composed of a mixture of p-type CuO and n-type WO3 nanoparticles (NPs) with optimized microstructure of the film and volumetric ratio of CuO to WO3 NPs in the film for enhanced H2 gas sensing. The NP-based thin films were synthesized using a magnetron-based gas aggregation source in Ar+O2 gas mixture. First, effect of thermal annealing on the microstructure (i.e., NPs diameter, formed necks, porosity) of the films was studied since gas sensing materials are usually operated at elevated temperatures (up to 400 °C). The CuO, WO3 and their composite (1:1 volumetric ratio) samples were annealed at temperatures in the range 200 - 400 °C in synthetic air and subsequently thoroughly investigated using various charaterisation techniques such as SEM, XRD, XPS, and Raman spectroscopy. Significant changes in particle size were observed in the case of CuO-based material, while WO3-based and composite materials exhibited minor microstructural changes, even at elevated temperatures. Notably, at 400°C, the composite crystallized into a novel phase. Second, the volumetric ratio of CuO to WO3 NPs in the films was optimized to maximize the response of the material. We demonstrate that a synergetic effect is reached when an optimum number of p–n heterojunctions is established in the material providing enhanced response of the composite film compared to the films formed by single-material NPs. This study highlights the crucial role of thermal treatment in influencing NP microstructure, offering insights into stabilizing and tuning NP-based thin films for enhanced gas sensing. Additionally, the optimized ratio of CuO and WO3 NPs within the composite improved H2 sensing performance by promoting optimal p–n heterojunction formation, demonstrating that precise compositional control can significantly boost the sensitivity of nanostructured systems.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (59) , 2782
Tailoring Microstructure and Composition of Composite CuO/WO3 Nanoparticle-Based Thin Films for Enhanced H2 Gas Sensing
The conductometric gas sensors operate by modulating the electrical conductivity of the sensing material through adsorption-desorption reactions between the target gas and the sensor surface. Metal oxide semiconductors (MOS) are conductometric materials highly sensitive to oxidizing and reducing gases. In addition, composite MOS-based materials may further benefit from formed heterojunctions potentially significantly improving the sensitivity. Our focus is to develop advanced hydrogen-gas sensing materials composed of a mixture of p-type CuO and n-type WO3 nanoparticles (NPs) with optimized microstructure of the film and volumetric ratio of CuO to WO3 NPs in the film for enhanced H2 gas sensing. The NP-based thin films were synthesized using a magnetron-based gas aggregation source in Ar+O2 gas mixture. First, effect of thermal annealing on the microstructure (i.e., NPs diameter, formed necks, porosity) of the films was studied since gas sensing materials are usually operated at elevated temperatures (up to 400 °C). The CuO, WO3 and their composite (1:1 volumetric ratio) samples were annealed at temperatures in the range 200 - 400 °C in synthetic air and subsequently thoroughly investigated using various charaterisation techniques such as SEM, XRD, XPS, and Raman spectroscopy. Significant changes in particle size were observed in the case of CuO-based material, while WO3-based and composite materials exhibited minor microstructural changes, even at elevated temperatures. Notably, at 400°C, the composite crystallized into a novel phase. Second, the volumetric ratio of CuO to WO3 NPs in the films was optimized to maximize the response of the material. We demonstrate that a synergetic effect is reached when an optimum number of p–n heterojunctions is established in the material providing enhanced response of the composite film compared to the films formed by single-material NPs. This study highlights the crucial role of thermal treatment in influencing NP microstructure, offering insights into stabilizing and tuning NP-based thin films for enhanced gas sensing. Additionally, the optimized ratio of CuO and WO3 NPs within the composite improved H2 sensing performance by promoting optimal p–n heterojunction formation, demonstrating that precise compositional control can significantly boost the sensitivity of nanostructured systems.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (38) , 1907
Corrosion-Resistant and Electrically Conductive Ti-Nb-O-Based Coatings for Metal Bipolar Plates and Porous Transport Layers in PEM Electrolyzers
The growing demand for flexible energy storage solutions has significantly accelerated the development of Proton Exchange Membrane Electrolysis (PEMEL) in recent years. Compared to conventional alkaline electrolysis with similar efficiency, PEMEL offers several key advantages, including dynamic operational characteristics, high power density, and the production of high-purity hydrogen. These attributes make PEMEL highly attractive for integration into renewable energy storage systems, such as those relying on solar and wind power. The critical components of PEM electrolyzer stacks are the bipolar plates (BPPs) and porous transport layers (PTLs), accounting for the main fraction of the total weight and cost. These components must possess excellent electrical conductivity, exceptional corrosion resistance, and a low interface contact resistance (ICR). The primary challenges arise from non-conductive oxide formation that increases ICR, hydrogen embrittlement of titanium, and the out-diffusion of metal ions from stainless steel, which can degrade the catalyst and electrolyte membrane. While the U.S. Department of Energy (DOE) targets corrosion current densities of < 1 µA/cm² and ICR of < 10 mΩ·cm² for bipolar plates in fuel cells, these values, though not directly applicable to PEM electrolyzers, provide useful benchmarks. These challenges can be addressed through the application of corrosion-resistant and electrically conductive coatings. This study investigates the use of Ti-Nb-O-based coatings prepared via reactive high-power impulse magnetron sputtering (HiPIMS) on SS316L sheet substrates. Reactive HiPIMS, an advanced and progressive deposition technique, enables the production of high-quality oxide coatings by utilizing the significant ionization of sputtered particles in the discharge plasma, which promotes densification and high crystallinity at low substrate temperatures. Prior to deposition, plasma etching with HiPIMS-generated argon and metal ions, accelerated by an applied bias voltage, was employed to remove the substrate’s native oxide layer. Coatings were deposited using an unbalanced magnetron equipped with a water-cooled planar target in an ultra-high vacuum chamber, with an argon-oxygen gas mixture at 1 Pa argon pressure. Precise control of oxygen partial pressure using a PID regulator, combined with fine Nb/Ti ratio adjustments, enabled the deposition of coatings with tailored stoichiometries for optimal electrical conductivity and corrosion resistance. The ICR between the test plate and a gas diffusion layer was measured under compaction pressures ranging from 0.3 to 2.0 MPa. The electrical resistivity of the coatings was assessed using a four-point probe system. Electrochemical measurements were conducted in a H₂SO₄ electrolyte solution (pH 5.0, fluorine ion concentration 5 ppm, temperature 60°C) to simulate the PEM electrolyzer environment. Accelerated corrosion tests were performed under extreme anodic conditions using potentiostatic polarization at 2 V vs. SHE. Corrosion behavior was further evaluated through open circuit potential, corrosion current, Tafel slopes, polarization resistance derived from potentiodynamic polarization curves (0 – 2 V vs. SHE), and electrochemical impedance spectroscopy (EIS). The Ti-Nb-O coatings demonstrated exceptional corrosion resistance, with corrosion current densities as low as ~ 0.01 µA/cm² measured after accelerated corrosion testing. Although the as-deposited coatings with optimized elemental composition achieved an ICR of <10 mΩ·cm², the accelerated corrosion test, using exaggerated potentials, significantly increased the ICR to several hundred mΩ·cm². Conventionally, a platinum (Pt) top layer, ranging from the higher tens to several hundred nanometers, is applied to maintain low ICR and improve corrosion resistance, albeit at a substantial cost. In this study, we also investigate the potential of Ti-Nb-O coatings to reduce the thickness of the Pt layer. Remarkably, applying only 5 nm of Pt atop the Ti-Nb-O coatings resulted in an ICR of < 20 mΩ·cm² after accelerated corrosion testing. This represents a reduction in Pt thickness by one to two orders of magnitude compared to conventional approaches. The combination of substantial Pt loading reduction and excellent corrosion resistance makes Ti-Nb-O coatings a highly promising solution for extending the lifetime and reducing the cost of PEM electrolyzers.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (38) , 1907
Corrosion-Resistant and Electrically Conductive Ti-Nb-O-Based Coatings for Metal Bipolar Plates and Porous Transport Layers in PEM Electrolyzers
The growing demand for flexible energy storage solutions has significantly accelerated the development of Proton Exchange Membrane Electrolysis (PEMEL) in recent years. Compared to conventional alkaline electrolysis with similar efficiency, PEMEL offers several key advantages, including dynamic operational characteristics, high power density, and the production of high-purity hydrogen. These attributes make PEMEL highly attractive for integration into renewable energy storage systems, such as those relying on solar and wind power. The critical components of PEM electrolyzer stacks are the bipolar plates (BPPs) and porous transport layers (PTLs), accounting for the main fraction of the total weight and cost. These components must possess excellent electrical conductivity, exceptional corrosion resistance, and a low interface contact resistance (ICR). The primary challenges arise from non-conductive oxide formation that increases ICR, hydrogen embrittlement of titanium, and the out-diffusion of metal ions from stainless steel, which can degrade the catalyst and electrolyte membrane. While the U.S. Department of Energy (DOE) targets corrosion current densities of < 1 µA/cm² and ICR of < 10 mΩ·cm² for bipolar plates in fuel cells, these values, though not directly applicable to PEM electrolyzers, provide useful benchmarks. These challenges can be addressed through the application of corrosion-resistant and electrically conductive coatings. This study investigates the use of Ti-Nb-O-based coatings prepared via reactive high-power impulse magnetron sputtering (HiPIMS) on SS316L sheet substrates. Reactive HiPIMS, an advanced and progressive deposition technique, enables the production of high-quality oxide coatings by utilizing the significant ionization of sputtered particles in the discharge plasma, which promotes densification and high crystallinity at low substrate temperatures. Prior to deposition, plasma etching with HiPIMS-generated argon and metal ions, accelerated by an applied bias voltage, was employed to remove the substrate’s native oxide layer. Coatings were deposited using an unbalanced magnetron equipped with a water-cooled planar target in an ultra-high vacuum chamber, with an argon-oxygen gas mixture at 1 Pa argon pressure. Precise control of oxygen partial pressure using a PID regulator, combined with fine Nb/Ti ratio adjustments, enabled the deposition of coatings with tailored stoichiometries for optimal electrical conductivity and corrosion resistance. The ICR between the test plate and a gas diffusion layer was measured under compaction pressures ranging from 0.3 to 2.0 MPa. The electrical resistivity of the coatings was assessed using a four-point probe system. Electrochemical measurements were conducted in a H₂SO₄ electrolyte solution (pH 5.0, fluorine ion concentration 5 ppm, temperature 60°C) to simulate the PEM electrolyzer environment. Accelerated corrosion tests were performed under extreme anodic conditions using potentiostatic polarization at 2 V vs. SHE. Corrosion behavior was further evaluated through open circuit potential, corrosion current, Tafel slopes, polarization resistance derived from potentiodynamic polarization curves (0 – 2 V vs. SHE), and electrochemical impedance spectroscopy (EIS). The Ti-Nb-O coatings demonstrated exceptional corrosion resistance, with corrosion current densities as low as ~ 0.01 µA/cm² measured after accelerated corrosion testing. Although the as-deposited coatings with optimized elemental composition achieved an ICR of <10 mΩ·cm², the accelerated corrosion test, using exaggerated potentials, significantly increased the ICR to several hundred mΩ·cm². Conventionally, a platinum (Pt) top layer, ranging from the higher tens to several hundred nanometers, is applied to maintain low ICR and improve corrosion resistance, albeit at a substantial cost. In this study, we also investigate the potential of Ti-Nb-O coatings to reduce the thickness of the Pt layer. Remarkably, applying only 5 nm of Pt atop the Ti-Nb-O coatings resulted in an ICR of < 20 mΩ·cm² after accelerated corrosion testing. This represents a reduction in Pt thickness by one to two orders of magnitude compared to conventional approaches. The combination of substantial Pt loading reduction and excellent corrosion resistance makes Ti-Nb-O coatings a highly promising solution for extending the lifetime and reducing the cost of PEM electrolyzers.
- Open Access
- 4 June 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 28
Thermally-induced microstructural evolution in nanoparticle-based CuO, WO 3 and CuO–WO 3 thin films for hydrogen gas sensing
- 4 June 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 28
Open AccessThermally-induced microstructural evolution in nanoparticle-based CuO, WO 3 and CuO–WO 3 thin films for hydrogen gas sensing
- Open Access
- 14 April 2025
- Published by Elsevier in Materials & Design
- Vol. 253
Unveiling effects of Zr alloying on structure and properties of nanocrystalline Cu-Zr films
- 14 April 2025
- Published by Elsevier in Materials & Design
- Vol. 253
Open AccessUnveiling effects of Zr alloying on structure and properties of nanocrystalline Cu-Zr films
- Open Access
- 10 March 2025
- Published by Elsevier in Scripta Materialia
- Vol. 262
New polymorph γ-CuWO4 inspired by γ-CuMoO4: Experimental identification and theoretical verification
- 10 March 2025
- Published by Elsevier in Scripta Materialia
- Vol. 262
Open AccessNew polymorph γ-CuWO4 inspired by γ-CuMoO4: Experimental identification and theoretical verification