Walid Mohamed Youssef
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Walid Mohamed Youssef has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
A. E. M. Hussein
Nuclear Materials Authority, Cairo, Egypt
2 shared publicationsM. H. Taha
Nuclear Materials Authority, Cairo, Egypt
2 shared publicationsA. E. M. Hussien
Nuclear Materials Authority, P.O. Box 530 Maadi, Cairo, Egypt
1 shared publicationA. S. Shalan
Nuclear Materials Authority, El-Maadi, Egypt
1 shared publicationAhmed M. Masoud
Nuclear Materials Authority, El Maadi, Cairo, Egypt
1 shared publicationEntesar M. El Gammal
Nuclear Materials Authority, El Maddi, Cairo, Egypt
1 shared publication
Latest Publications
- Open Access
- 29 October 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (47) , 34526-34536
Recovery of uranium using epoxy-modified phosphorus pentasulfide as an efficient adsorbent for uranium extraction from aquatic environments
Epoxy-modified phosphorus pentasulfide (EPMPS) formulation was developed for the supported recovery of uranium from aquatic environments. The selected components of the prepared formulation were tailored to produce a rigid foamed polymeric material that was rich in phosphorus, nitrogen, sulfur and oxygen atoms, thus increasing chelating bonding possibilities with uranium. FT-IR and SEM were applied to physically characterize the resulting sorbent. At an equilibrium time of 30 min, the phase ratio S/L of 1 g L−1, pH 3 and initial uranium concentration of 50 mg L−1 yielded an adsorption efficiency for uranium of 90%. An 85% elution of uranium from loaded EPMPS was achieved with 1 h shaking and a phase ratio (S/A) of 0.5 g/25 mL of 0.1 M CH3COONa. Sorption isotherm designs were exploited to analyze the findings from the experiments. Uranium had an adsorption capability of about 78.7 mg g−1. According to the results of uranium adsorption, when applied to an actual sample, EPMPS is a suitable substrate for uranium adsorption from nitrate media.
- 29 October 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (47) , 34526-34536
Open AccessRecovery of uranium using epoxy-modified phosphorus pentasulfide as an efficient adsorbent for uranium extraction from aquatic environments
Epoxy-modified phosphorus pentasulfide (EPMPS) formulation was developed for the supported recovery of uranium from aquatic environments. The selected components of the prepared formulation were tailored to produce a rigid foamed polymeric material that was rich in phosphorus, nitrogen, sulfur and oxygen atoms, thus increasing chelating bonding possibilities with uranium. FT-IR and SEM were applied to physically characterize the resulting sorbent. At an equilibrium time of 30 min, the phase ratio S/L of 1 g L−1, pH 3 and initial uranium concentration of 50 mg L−1 yielded an adsorption efficiency for uranium of 90%. An 85% elution of uranium from loaded EPMPS was achieved with 1 h shaking and a phase ratio (S/A) of 0.5 g/25 mL of 0.1 M CH3COONa. Sorption isotherm designs were exploited to analyze the findings from the experiments. Uranium had an adsorption capability of about 78.7 mg g−1. According to the results of uranium adsorption, when applied to an actual sample, EPMPS is a suitable substrate for uranium adsorption from nitrate media.
- 1 October 2024
- Published by Pleiades Publishing Ltd in Radiochemistry
- Vol. 66 (5) , 624-632
Studying the Performance of Aminotrimethylenephosphonic Acid for the Removal of Iron with Subsequent Recovery of Uranium from Sulfate Leach Liquor
This study examined the effectiveness of using aminotrimethylenephosphonic acid (ATMP) as a chelating agent to remove iron from Abu Zeneima sulfate leach liquor (AZSLL) and recover uranium as a result. Key parameters including pH, ATMP to sample volume ratio, contact time, and temperature were systematically examined to find the ideal conditions for iron removal. The findings revealed a remarkable selectivity in iron removal by precipitation with 0.05 M aminotrimethylenephosphonic acid (ATMP) per 10 mL of the sample: 90% of iron was precipitated, which is equivalent to approximately 20.5 mg, without adversely impacting uranium content. The iron amputation provided a favorable opportunity for the subsequent recovery of uranium, employing trioctylamine (TOA) as the extracting agent. TOA dissolved in benzene demonstrated efficiency in uranium recovery. The effect of the type of stripping solution, organic/aqueous phase volume ratio, contact time, and temperature on the uranium stripping was examined. Under the optimized conditions, with a maximum stripping efficiency of 98%, the uranium concentration in the resulting solution reached 451.58 mg/L.
- 1 October 2024
- Published by Pleiades Publishing Ltd in Radiochemistry
- Vol. 66 (5) , 624-632
Studying the Performance of Aminotrimethylenephosphonic Acid for the Removal of Iron with Subsequent Recovery of Uranium from Sulfate Leach Liquor
This study examined the effectiveness of using aminotrimethylenephosphonic acid (ATMP) as a chelating agent to remove iron from Abu Zeneima sulfate leach liquor (AZSLL) and recover uranium as a result. Key parameters including pH, ATMP to sample volume ratio, contact time, and temperature were systematically examined to find the ideal conditions for iron removal. The findings revealed a remarkable selectivity in iron removal by precipitation with 0.05 M aminotrimethylenephosphonic acid (ATMP) per 10 mL of the sample: 90% of iron was precipitated, which is equivalent to approximately 20.5 mg, without adversely impacting uranium content. The iron amputation provided a favorable opportunity for the subsequent recovery of uranium, employing trioctylamine (TOA) as the extracting agent. TOA dissolved in benzene demonstrated efficiency in uranium recovery. The effect of the type of stripping solution, organic/aqueous phase volume ratio, contact time, and temperature on the uranium stripping was examined. Under the optimized conditions, with a maximum stripping efficiency of 98%, the uranium concentration in the resulting solution reached 451.58 mg/L.
- Open Access
- 4 April 2024
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 333 (4) , 1975-1989
Uranium (VI) sorption from aqueous solution using commercial anion exchange resins; kinetics, isotherm, and thermodynamic investigations
Commercial strong anion exchange resins provided by Purolite, namely MTA4801PF, and MTA4601PFSO4, were utilized for extracting uranium from sulfate leach liquor. The study focused on investigating the kinetics, isotherms, and thermodynamics of the sorption process. Both resins demonstrated similar kinetics and isotherm performance, with sorption capacities of approximately 66 and 71 mg g−1respectively. The sorption process was proven to be endothermic, feasible, and spontaneous, and U(VI) desorption of around 95% was achieved using 0.5 M sulfuric acid. Commercial resins showed excellent sorption performance when applied to sulfate leach liquor of Egyptian ores despite the complexity of the solution.
- 4 April 2024
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 333 (4) , 1975-1989
Open AccessUranium (VI) sorption from aqueous solution using commercial anion exchange resins; kinetics, isotherm, and thermodynamic investigations
Commercial strong anion exchange resins provided by Purolite, namely MTA4801PF, and MTA4601PFSO4, were utilized for extracting uranium from sulfate leach liquor. The study focused on investigating the kinetics, isotherms, and thermodynamics of the sorption process. Both resins demonstrated similar kinetics and isotherm performance, with sorption capacities of approximately 66 and 71 mg g−1respectively. The sorption process was proven to be endothermic, feasible, and spontaneous, and U(VI) desorption of around 95% was achieved using 0.5 M sulfuric acid. Commercial resins showed excellent sorption performance when applied to sulfate leach liquor of Egyptian ores despite the complexity of the solution.
- 18 October 2022
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 104 (17) , 5927-5946
Solid–liquid extraction of uranium from aqueous solution using Marathon C as a strong cation exchanger resin: kinetic, and isotherm studies
In this study, Adsorption characteristics of uranium from nitrate media onto a commercially accessible strong cation exchange resin, Marathon C, were investigated. The characteristics of Marathon C, before and after adsorption of uranium, were determined using scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The influence of the different parameters, which may affect the process of uranium adsorption process from synthetic solutions and applying on real sample from uranium purification unit, had been tracked. Specifically, impacts of initial uranium concentration (40–300 mg/L), PH (1–8), phase ratio (0.2–1.2 g/L), contact time (2–360 min.) and temperature (& 25–50°C) on uranium removal, were studied. In addition, the sorption kinetics and equilibrium parameters were assessed. At the optimum conditions, the adsorption capacity of uranium at PH 4, 1 g Marathon C/L and 120 min were found to be nearly 131.58 mg g−1 at room temperature (& 25°C). The kinetics and isotherm studies could show that the uranium adsorption onto Marathon C is following the models of pseudo-second-order and Langmuir isotherm, respectively. The thermodynamic parameters had indicated that the adsorption of uranium is an exothermic and spontaneous process (∆H = −64.27 ± 0.01, ∆G = −22.57 ± 0.02). The detected results of uranium adsorption could reveal that Marathon C is a suitable material for adsorption of uranium from nitrate media and applying on real sample from uranium purification unit.
- 18 October 2022
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 104 (17) , 5927-5946
Solid–liquid extraction of uranium from aqueous solution using Marathon C as a strong cation exchanger resin: kinetic, and isotherm studies
In this study, Adsorption characteristics of uranium from nitrate media onto a commercially accessible strong cation exchange resin, Marathon C, were investigated. The characteristics of Marathon C, before and after adsorption of uranium, were determined using scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The influence of the different parameters, which may affect the process of uranium adsorption process from synthetic solutions and applying on real sample from uranium purification unit, had been tracked. Specifically, impacts of initial uranium concentration (40–300 mg/L), PH (1–8), phase ratio (0.2–1.2 g/L), contact time (2–360 min.) and temperature (& 25–50°C) on uranium removal, were studied. In addition, the sorption kinetics and equilibrium parameters were assessed. At the optimum conditions, the adsorption capacity of uranium at PH 4, 1 g Marathon C/L and 120 min were found to be nearly 131.58 mg g−1 at room temperature (& 25°C). The kinetics and isotherm studies could show that the uranium adsorption onto Marathon C is following the models of pseudo-second-order and Langmuir isotherm, respectively. The thermodynamic parameters had indicated that the adsorption of uranium is an exothermic and spontaneous process (∆H = −64.27 ± 0.01, ∆G = −22.57 ± 0.02). The detected results of uranium adsorption could reveal that Marathon C is a suitable material for adsorption of uranium from nitrate media and applying on real sample from uranium purification unit.
- 23 May 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Inorganic Chemistry
- Vol. 67 (7) , 1058-1068
Uranium(VI) Sorption from Liquid Waste Solution Using Functionalized Polyurethane Polymer: Kinetic and Isotherm Characterizations
The removal of hazardous metal ions from liquid waste effluents is very important for water as well as environmental security. In this regard, this article discusses the adsorption of hexavalent uranium U(VI) from aqueous solutions onto polyether type polyurethane foam in detail (PUF). SEM and FTIR measurements were used to characterize PUF prior to and after U(VI) adsorption, and batch-type experiments were used to investigate the effect of various parameters on adsorption efficiency, including pH, metal-ion concentration, temperature, and contact time. The sorption experimental data have been described well with pseudo-second-order kinetic mathematical equations. The Langmuir isotherm model accurately described the equilibrium process which declare that the uranium sorption is monolayer and homogeneous process. The sorption capacity of conventional polyurethane foam was 26.3 mg g–1. Nitric acid (0.1 M) has been applied effectively for the desorption of U(VI) from the loaded sorbent. PUF material exhibit stable performance for five cycles of sorption/ desorption processes. The displayed results demonstrate that PUF may be used as a proper material for uranium sorption from real matrix samples.
- 23 May 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Inorganic Chemistry
- Vol. 67 (7) , 1058-1068
Uranium(VI) Sorption from Liquid Waste Solution Using Functionalized Polyurethane Polymer: Kinetic and Isotherm Characterizations
The removal of hazardous metal ions from liquid waste effluents is very important for water as well as environmental security. In this regard, this article discusses the adsorption of hexavalent uranium U(VI) from aqueous solutions onto polyether type polyurethane foam in detail (PUF). SEM and FTIR measurements were used to characterize PUF prior to and after U(VI) adsorption, and batch-type experiments were used to investigate the effect of various parameters on adsorption efficiency, including pH, metal-ion concentration, temperature, and contact time. The sorption experimental data have been described well with pseudo-second-order kinetic mathematical equations. The Langmuir isotherm model accurately described the equilibrium process which declare that the uranium sorption is monolayer and homogeneous process. The sorption capacity of conventional polyurethane foam was 26.3 mg g–1. Nitric acid (0.1 M) has been applied effectively for the desorption of U(VI) from the loaded sorbent. PUF material exhibit stable performance for five cycles of sorption/ desorption processes. The displayed results demonstrate that PUF may be used as a proper material for uranium sorption from real matrix samples.
- 1 April 2022
- Published by Pleiades Publishing Ltd in Radiochemistry
- Vol. 64 (2) , 244-256
Wall Rock Alteration, Uranium Mineralization, and Potentiality of Uranium and Iron Dissolution from Mineralized Abu Rusheid Gneiss Rock, South Eastern Desert, Egypt
Ferrugination, sericitization, desulfitization, chloritization, and kaolinitization of hydrothermal origin are the main wall rock alterations occurring within the NNW shear zones at Abu Rusheid area. The secondary uranium minerals occur as hair-like radiated spots and thin micaceous flakes with canary and yellow color, which are deposited along the small cracks and microfractures of altered gneiss and lamprophyre dyke and coat surfaces of hematitized rock. The radiometric measurements proved that the uranium content increases from sericitized gneiss (average 317.9 ppm) to ferruginated gneiss (average 863.1 ppm) and then to altered lamprophyre dyke (average 1352.7 ppm). The latter is the most radioactive zone along the NNW shear zones and is considered as a good trap for the uranium leached from the host rock due to the high ability of iron oxides and clays to adsorb radioactive elements from their solutions. Therefore, the present work focuses on the uranium leaching from Abu Rusheid area using sulfuric acid. The effect of sulfuric acid concentration, liquid/solid ratio, contact time, and leaching temperature on the leaching efficiency has been investigated. The data obtained show that about 74.0% of uranium can be leached successfully under the following conditions: sulfuric acid concentration 4 M, liquid/solid ratio 10 mL/g, room temperature, 6.0 h. The leaching kinetics is well interpreted with shrinking core model with control by diffusion through a porous product layer. The diffusion-controlled process is characterized by the activation energy of 6.3 kJ mol–1.
- 1 April 2022
- Published by Pleiades Publishing Ltd in Radiochemistry
- Vol. 64 (2) , 244-256
Wall Rock Alteration, Uranium Mineralization, and Potentiality of Uranium and Iron Dissolution from Mineralized Abu Rusheid Gneiss Rock, South Eastern Desert, Egypt
Ferrugination, sericitization, desulfitization, chloritization, and kaolinitization of hydrothermal origin are the main wall rock alterations occurring within the NNW shear zones at Abu Rusheid area. The secondary uranium minerals occur as hair-like radiated spots and thin micaceous flakes with canary and yellow color, which are deposited along the small cracks and microfractures of altered gneiss and lamprophyre dyke and coat surfaces of hematitized rock. The radiometric measurements proved that the uranium content increases from sericitized gneiss (average 317.9 ppm) to ferruginated gneiss (average 863.1 ppm) and then to altered lamprophyre dyke (average 1352.7 ppm). The latter is the most radioactive zone along the NNW shear zones and is considered as a good trap for the uranium leached from the host rock due to the high ability of iron oxides and clays to adsorb radioactive elements from their solutions. Therefore, the present work focuses on the uranium leaching from Abu Rusheid area using sulfuric acid. The effect of sulfuric acid concentration, liquid/solid ratio, contact time, and leaching temperature on the leaching efficiency has been investigated. The data obtained show that about 74.0% of uranium can be leached successfully under the following conditions: sulfuric acid concentration 4 M, liquid/solid ratio 10 mL/g, room temperature, 6.0 h. The leaching kinetics is well interpreted with shrinking core model with control by diffusion through a porous product layer. The diffusion-controlled process is characterized by the activation energy of 6.3 kJ mol–1.
- Open Access
- 1 January 2020
- Published by Egyptian Knowledge Bank in Journal of Basic and Environmental Sciences
- Vol. 7 (1) , 1-12
Characterization and Application of Olive Stones Activated Carbon for Uranium (VI) Sorption from Wet-process phosphoric acid: Kinetic, equilibrium and thermodynamic studies
In this work, uranium adsorption from Egyptian phosphoric acid onto chemical modified Olive Stones has beenstudied by two methods (H3PO4 and ZnCl2) at 800ºC was used to carbonized. The relevant factors affecting uraniumadsorption onto our Olive Stones Activated Carbon adsorbent were studied. These factors involved phosphoric acidconcentration, the contact time, adsorbent weight, initial uranium concentration and the temperature were investigated.The theoretical capacity of Olive Stones Activated Carbon adsorbent is about (47.8, 46.08) mg/g for O.S-H3PO4, O.SZnCl2 respectively. The optimum adsorption conditions were choiced in two methods and P2O5 ineffective by theseconditions. The sorption process of uranium U(VI) follow Langmuir isotherm model with pseudo-second ordermechanism and exothermic nature and spontaneous process according to studying (enthalpy change, entropy change andGibbs free energy change). More Than 80 % of the loaded uranium amount on the Olive Stones Activated Carbonadsorbent has been eluted using 0.1 M HNO3 as an efficient eluent.
- 1 January 2020
- Published by Egyptian Knowledge Bank in Journal of Basic and Environmental Sciences
- Vol. 7 (1) , 1-12
Open AccessCharacterization and Application of Olive Stones Activated Carbon for Uranium (VI) Sorption from Wet-process phosphoric acid: Kinetic, equilibrium and thermodynamic studies
In this work, uranium adsorption from Egyptian phosphoric acid onto chemical modified Olive Stones has beenstudied by two methods (H3PO4 and ZnCl2) at 800ºC was used to carbonized. The relevant factors affecting uraniumadsorption onto our Olive Stones Activated Carbon adsorbent were studied. These factors involved phosphoric acidconcentration, the contact time, adsorbent weight, initial uranium concentration and the temperature were investigated.The theoretical capacity of Olive Stones Activated Carbon adsorbent is about (47.8, 46.08) mg/g for O.S-H3PO4, O.SZnCl2 respectively. The optimum adsorption conditions were choiced in two methods and P2O5 ineffective by theseconditions. The sorption process of uranium U(VI) follow Langmuir isotherm model with pseudo-second ordermechanism and exothermic nature and spontaneous process according to studying (enthalpy change, entropy change andGibbs free energy change). More Than 80 % of the loaded uranium amount on the Olive Stones Activated Carbonadsorbent has been eluted using 0.1 M HNO3 as an efficient eluent.