Ilyas Ablakatov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ilyas Ablakatov has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Berdiyar Baiserikov
National Center for Space Research and Technology, Almaty, Kazakhstan
3 shared publications - Laura Mustafa
JSC “National Center of Space Research and Technology”, Almaty 050010, Kazakhstan
3 shared publications - Marat Ismailov
National Center for Space Research and Technology, Almaty, Kazakhstan
3 shared publications - Ablaikhan Baigonov
National Center for Space Research and Technology, Almaty, Kazakhstan
2 shared publications - Abussaid Yermekov
JSC “National Center of Space Research and Technology”, Almaty 050010, Kazakhstan
1 shared publication - Arman Kulbekov
JSC “National Center of Space Research and Technology”, Almaty 050010, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 8 June 2026
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 17 (1) , 32-39
INVESTIGATION OF THE EFFECT OF REACTIVE DILUENTS ON THE MECHANICAL PROPERTIES OF EPOXY BINDERS
The effect of various types of curing agents and reactive diluents on the rheological and mechanical properties of epoxy binders was investigated. “Etal Inject-T” and “Larit L-285” epoxy resins were used as matrices. “Etal Inject-T”, iso-MTHPA, dicyandiamide (DICY), and diaminodiphenylsulfone (DDS) were used as curing agents. The effect of reactive diluents – glycerol triglycidyl ether, pentaerythritol tetraglycidyl ether, and butyl glycidyl ether – was also studied. Maximum strength characteristics were achieved using DDS curing agent at 25%. For the “Etal Inject-T” system, compressive strength values of 140 MPa were obtained. It was shown that the addition of pentaerythritol tetraglycidyl ether at 10% simultaneously reduces the viscosity of the epoxy composition from 400 mPa·s to 280 mPa·s and increases compressive strength from 140 MPa to 155 MPa. The results demonstrate the high effectiveness of multifunctional glycidyl ethers for controlling the structure and mechanical properties of epoxy binders. Keywords: epoxy resins, reactive diluents, curing agents, mechanical properties, viscosity, epoxy compositions.
- 8 June 2026
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 17 (1) , 32-39
Open AccessINVESTIGATION OF THE EFFECT OF REACTIVE DILUENTS ON THE MECHANICAL PROPERTIES OF EPOXY BINDERS
The effect of various types of curing agents and reactive diluents on the rheological and mechanical properties of epoxy binders was investigated. “Etal Inject-T” and “Larit L-285” epoxy resins were used as matrices. “Etal Inject-T”, iso-MTHPA, dicyandiamide (DICY), and diaminodiphenylsulfone (DDS) were used as curing agents. The effect of reactive diluents – glycerol triglycidyl ether, pentaerythritol tetraglycidyl ether, and butyl glycidyl ether – was also studied. Maximum strength characteristics were achieved using DDS curing agent at 25%. For the “Etal Inject-T” system, compressive strength values of 140 MPa were obtained. It was shown that the addition of pentaerythritol tetraglycidyl ether at 10% simultaneously reduces the viscosity of the epoxy composition from 400 mPa·s to 280 mPa·s and increases compressive strength from 140 MPa to 155 MPa. The results demonstrate the high effectiveness of multifunctional glycidyl ethers for controlling the structure and mechanical properties of epoxy binders. Keywords: epoxy resins, reactive diluents, curing agents, mechanical properties, viscosity, epoxy compositions.
- Open Access
- 29 April 2026
- Published by Elsevier in SSRN Electronic Journal
Thermomechanical Analysis of Materials for the Nozzle Assembly of a Liquid Rocket Engine
This study presents a numerical investigation of the thermophysical and mechanical characteristics of a liquid rocket engine nozzle assembly with regenerative cooling. The simulations were performed using Ansys Discovery, Ansys Steady-State Thermal, and Ansys Mechanical software packages. Various combinations of structural materials (copper, aluminum, and steel) were analyzed, along with the influence of the convective heat transfer coefficient on the thermal state of the structure. It was found that increasing the coolant heat transfer coefficient up to 1.2 W/mm²·K significantly reduces the temperature of the inner layer, thereby ensuring acceptable operating conditions. Based on the results obtained, a nozzle design was developed featuring an inner layer made of a CuCrZr alloy and an outer shell made of 30KhGSA steel with a regenerative cooling system. The proposed design ensures stable operation at temperatures up to 3000 K and internal pressures up to 6 MPa with a safety factor of at least 1.5. The proposed approach provides a practical framework for the design and material selection of high-performance rocket engine nozzle assemblies.
- 29 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermomechanical Analysis of Materials for the Nozzle Assembly of a Liquid Rocket Engine
This study presents a numerical investigation of the thermophysical and mechanical characteristics of a liquid rocket engine nozzle assembly with regenerative cooling. The simulations were performed using Ansys Discovery, Ansys Steady-State Thermal, and Ansys Mechanical software packages. Various combinations of structural materials (copper, aluminum, and steel) were analyzed, along with the influence of the convective heat transfer coefficient on the thermal state of the structure. It was found that increasing the coolant heat transfer coefficient up to 1.2 W/mm²·K significantly reduces the temperature of the inner layer, thereby ensuring acceptable operating conditions. Based on the results obtained, a nozzle design was developed featuring an inner layer made of a CuCrZr alloy and an outer shell made of 30KhGSA steel with a regenerative cooling system. The proposed design ensures stable operation at temperatures up to 3000 K and internal pressures up to 6 MPa with a safety factor of at least 1.5. The proposed approach provides a practical framework for the design and material selection of high-performance rocket engine nozzle assemblies.
- Open Access
- 11 November 2024
- Published by Pandawa Institute in Journal of Multidisciplinary Applied Natural Science
- Vol. 5 (1) , 130-140
The Effect of Modifiers on the Strength and Impact Toughness of Carbon Fiber Reinforced Plastics
This study utilized epoxy resin, three types of fabric (carbon fiber, glass fiber, and Kevlar), and two plasticizers – tricresyl phosphate (TCP) and oleic acid (OA) – to enhance the impact toughness of carbon fiber-reinforced plastics (CFRP). The polymer matrix used in the experiments was a hot-cured epoxy compound "Etal Inject-T" consisting of two components: A – epoxy resin and B – hardener, in a mass ratio of 100:49.9. For the fabrication of CFRP plates, both manual and vacuum molding techniques were employed. Combined reinforcement of carbon fiber was achieved using one of two types of fabrics: Ortex 360 glass fiber or Kevlar. Accordingly, two compositions were prepared for the experiments: carbon fiber/glass fiber and carbon fiber/Kevlar. Layer stacking in each composition was performed at ratios of 10:10 and 14:6, consisting of 20 layers in total. The greatest strengthening effect for CFRP in the case of carbon fiber/glass fiber was observed with a layer ratio of 14:6 and matrix modification using 10% TCP plasticizer. The strength of the CFRP increased from 425 to 451 MPa, and the impact toughness (α) improved from 192 to 280 kJ/m². A key feature of this technology is the achievement of high-performance dual-purpose CFRP. This enables the reduction of CFRP structures in aerospace applications by 3 to 5 times, while simultaneously enhancing resistance to impact loads.
- 11 November 2024
- Published by Pandawa Institute in Journal of Multidisciplinary Applied Natural Science
- Vol. 5 (1) , 130-140
Open AccessThe Effect of Modifiers on the Strength and Impact Toughness of Carbon Fiber Reinforced Plastics
This study utilized epoxy resin, three types of fabric (carbon fiber, glass fiber, and Kevlar), and two plasticizers – tricresyl phosphate (TCP) and oleic acid (OA) – to enhance the impact toughness of carbon fiber-reinforced plastics (CFRP). The polymer matrix used in the experiments was a hot-cured epoxy compound "Etal Inject-T" consisting of two components: A – epoxy resin and B – hardener, in a mass ratio of 100:49.9. For the fabrication of CFRP plates, both manual and vacuum molding techniques were employed. Combined reinforcement of carbon fiber was achieved using one of two types of fabrics: Ortex 360 glass fiber or Kevlar. Accordingly, two compositions were prepared for the experiments: carbon fiber/glass fiber and carbon fiber/Kevlar. Layer stacking in each composition was performed at ratios of 10:10 and 14:6, consisting of 20 layers in total. The greatest strengthening effect for CFRP in the case of carbon fiber/glass fiber was observed with a layer ratio of 14:6 and matrix modification using 10% TCP plasticizer. The strength of the CFRP increased from 425 to 451 MPa, and the impact toughness (α) improved from 192 to 280 kJ/m². A key feature of this technology is the achievement of high-performance dual-purpose CFRP. This enables the reduction of CFRP structures in aerospace applications by 3 to 5 times, while simultaneously enhancing resistance to impact loads.
- 23 May 2022
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 323 (4) , 5-14
Aluminum-lithium alloys: types, properties, application, and production technologies. Overview
The article provides a brief overview of the aluminum industry development in Kazakhstan and the possibility of obtaining high-strength structural aluminum-lithium alloys. The country's enterprises produce aluminum of technical purity and aluminum alloys of low and medium strength of 6060, 6063, 6463, 6082, AK5M2, ADS-12, AD-31, AD-35, which are available materials for the construction industry. In Kazakhstan, there is progressive development of mechanical engineering which requires stronger alloys of 300-400 MPa, and for special engineering (defense, aerospace, and other advanced industries) - strengths above 415 MPa. High-strength structural aluminum alloys are based on Al-Cu-Mg, Al-Zn-Mg-Cu, Al-Li systems. Among these systems, relatively new Al-Li alloys are of great interest, having a great potential for further improvement of characteristics. The Al-Li system alloys with record-high specific strengths, corrosion-resistant, and good welded joints are widely used in the aerospace industry, where they are used for the production of power elements and housings. The article provides an overview of the known aluminum-lithium alloys, as well as the main technological stages of their production.
- 23 May 2022
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 323 (4) , 5-14
Aluminum-lithium alloys: types, properties, application, and production technologies. Overview
The article provides a brief overview of the aluminum industry development in Kazakhstan and the possibility of obtaining high-strength structural aluminum-lithium alloys. The country's enterprises produce aluminum of technical purity and aluminum alloys of low and medium strength of 6060, 6063, 6463, 6082, AK5M2, ADS-12, AD-31, AD-35, which are available materials for the construction industry. In Kazakhstan, there is progressive development of mechanical engineering which requires stronger alloys of 300-400 MPa, and for special engineering (defense, aerospace, and other advanced industries) - strengths above 415 MPa. High-strength structural aluminum alloys are based on Al-Cu-Mg, Al-Zn-Mg-Cu, Al-Li systems. Among these systems, relatively new Al-Li alloys are of great interest, having a great potential for further improvement of characteristics. The Al-Li system alloys with record-high specific strengths, corrosion-resistant, and good welded joints are widely used in the aerospace industry, where they are used for the production of power elements and housings. The article provides an overview of the known aluminum-lithium alloys, as well as the main technological stages of their production.