Siddharth Yadav
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Siddharth Yadav has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Jayant Kumar Singh
Department of Metallurgical Engineering, Indian Institute of Technology (BHU), Varanasi, India
2 shared publicationsManish Deo
Department of Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, India
2 shared publicationsRabindra Prasad
Department of Mechanical Engineering, Amity University, Gwalior, India
2 shared publicationsSantosh Kumar
Department of Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, India
2 shared publicationsSatya Prakash Tewari
Department of Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, India
2 shared publicationsSubhash Chandra Ram
Department of Mechanical Engineering, Tulas Institute Dhoolkot Near Selaqui, Dehradun, India
2 shared publications
Latest Publications
- 12 August 2025
- Published by Springer Nature
- p. 237-259
Recent Trends in Natural Fiber Reinforced HDPE Composites: Progress and Challenges
- 12 August 2025
- Published by Springer Nature
- p. 237-259
Recent Trends in Natural Fiber Reinforced HDPE Composites: Progress and Challenges
- Open Access
- 25 July 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (8) , 325
An Investigation on the Effect of Mango Seed and Pongamia Oil-Based Cutting Fluids on Surface Morphology During Turning of AISI 304 Steel
In today’s industrial applications, cutting fluids have attained prime importance due to their all-round features, including increase of tool life by lubrication of the tool at the tool–workpiece interface. This study compares the effects of mango seed oil and pongamia oil on cutting force and surface morphology during the turning of AISI 304 steel. The design of experiments was applied using Taguchi’s method with an L9 array of experiments. During the experiment, it was discovered that mango seed and pongamia-based cutting fluid exhibited the lowest contact angles of 22.1° and 24.4°, respectively, at a 97:3 volumetric concentration of deionized water and eco-friendly oil. The use of mango seed oil as a cutting fluid with MQL (Minimum Quantity Lubrication) resulted in the lowest surface roughness of 0.809 µm, compared to 0.921 µm with pongamia-based cutting fluid. The cutting force was reduced by a maximum of 28.68% using mango seed-based cutting fluid, compared to pongamia-based cutting fluid. ANOVA analysis revealed that feed rate had the maximum influence on the optimization of output parameters for mango seed cutting fluid. For pongamia-based cutting fluid, feed rate had the maximum influence on cutting force, while the depth of cut had the strongest influence on surface roughness.
- 25 July 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (8) , 325
Open AccessAn Investigation on the Effect of Mango Seed and Pongamia Oil-Based Cutting Fluids on Surface Morphology During Turning of AISI 304 Steel
In today’s industrial applications, cutting fluids have attained prime importance due to their all-round features, including increase of tool life by lubrication of the tool at the tool–workpiece interface. This study compares the effects of mango seed oil and pongamia oil on cutting force and surface morphology during the turning of AISI 304 steel. The design of experiments was applied using Taguchi’s method with an L9 array of experiments. During the experiment, it was discovered that mango seed and pongamia-based cutting fluid exhibited the lowest contact angles of 22.1° and 24.4°, respectively, at a 97:3 volumetric concentration of deionized water and eco-friendly oil. The use of mango seed oil as a cutting fluid with MQL (Minimum Quantity Lubrication) resulted in the lowest surface roughness of 0.809 µm, compared to 0.921 µm with pongamia-based cutting fluid. The cutting force was reduced by a maximum of 28.68% using mango seed-based cutting fluid, compared to pongamia-based cutting fluid. ANOVA analysis revealed that feed rate had the maximum influence on the optimization of output parameters for mango seed cutting fluid. For pongamia-based cutting fluid, feed rate had the maximum influence on cutting force, while the depth of cut had the strongest influence on surface roughness.
- 14 July 2022
- Published by Springer Nature in Silicon
- Vol. 15 (1) , 229-241
Influence of High Amplitude Mould Vibration on the Morphology of Silicon in the Al-Si Alloy (A308)
- 14 July 2022
- Published by Springer Nature in Silicon
- Vol. 15 (1) , 229-241
Influence of High Amplitude Mould Vibration on the Morphology of Silicon in the Al-Si Alloy (A308)
- 12 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (3) , 710-718
Influence of high-intensity horizontal mould vibration on the density, grain refinement and mechanical characteristics of a die cast aluminium alloy (LM21)
The present investigation analysed the effect of mould vibration using an indigenous vibrating setup on the physical, metallurgical and mechanical properties of die cast A308 alloy. The alloy was vibrated at a constant amplitude of 31µm at 75, 100, 125 and 150 Hz. The work aims to generate more nucleation sites during melt solidification by fragmenting dendrites and Si particles. To examine the changes in metallurgical characteristics, α-Al, secondary dendritic arm spacing, length, width and aspect ratio of eutectic Si particles were studied using optical microscopy, scanning electron microscopy and X-ray diffraction analysis. It was observed that the size of α-Al, secondary dendritic arm spacing, length, width and aspect ratio of eutectic Si particles were decreased by 47%, 53%, 65%, 12% and 61%, respectively. Whereas, the shape factor and density of the alloy were enhanced by 25% and 1.62% compared to stationary cast samples because of mechanical vibration treatment at an optimum frequency of 100 Hz. Mechanical testing findings demonstrated a 13%, 20%, 15% and 20% increase in the parameters such as yield strength, ultimate tensile strength, percentage elongation and microhardness at 100 Hz when compared to the stationary cast sample. Grain refinement, uniformity of structure, improvement in the morphology of metallurgical characteristics, decreased porosities and subsequent increase in density were all factors that contributed to the improvement. Tensile test samples with scanning electron microscopy fractography demonstrated transgranular brittle fracture and a few ductile rips.
- 12 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 237 (3) , 710-718
Influence of high-intensity horizontal mould vibration on the density, grain refinement and mechanical characteristics of a die cast aluminium alloy (LM21)
The present investigation analysed the effect of mould vibration using an indigenous vibrating setup on the physical, metallurgical and mechanical properties of die cast A308 alloy. The alloy was vibrated at a constant amplitude of 31µm at 75, 100, 125 and 150 Hz. The work aims to generate more nucleation sites during melt solidification by fragmenting dendrites and Si particles. To examine the changes in metallurgical characteristics, α-Al, secondary dendritic arm spacing, length, width and aspect ratio of eutectic Si particles were studied using optical microscopy, scanning electron microscopy and X-ray diffraction analysis. It was observed that the size of α-Al, secondary dendritic arm spacing, length, width and aspect ratio of eutectic Si particles were decreased by 47%, 53%, 65%, 12% and 61%, respectively. Whereas, the shape factor and density of the alloy were enhanced by 25% and 1.62% compared to stationary cast samples because of mechanical vibration treatment at an optimum frequency of 100 Hz. Mechanical testing findings demonstrated a 13%, 20%, 15% and 20% increase in the parameters such as yield strength, ultimate tensile strength, percentage elongation and microhardness at 100 Hz when compared to the stationary cast sample. Grain refinement, uniformity of structure, improvement in the morphology of metallurgical characteristics, decreased porosities and subsequent increase in density were all factors that contributed to the improvement. Tensile test samples with scanning electron microscopy fractography demonstrated transgranular brittle fracture and a few ductile rips.
- 23 May 2022
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 29 (6) , 1206-1215
Effects of mechanical vibration on the physical, metallurgical and mechanical properties of cast A308 (LM21) aluminum alloy
- 23 May 2022
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 29 (6) , 1206-1215
Effects of mechanical vibration on the physical, metallurgical and mechanical properties of cast A308 (LM21) aluminum alloy